Concept explainers
Using the rules for parallel circuits and Ohm’slaw, solve for the missing values.
Want to see the full answer?
Check out a sample textbook solutionChapter 7 Solutions
Delmar's Standard Textbook Of Electricity
- 3.18 In a single-phase half-wave ac-dc converter, the average value of the load current is 1.78 A. If the converter is operated from a 240 V, 50 Hz supply and if the average value of the output voltage is 27% of the maximum possible value, calculate the following, assume the load to be resistive. (a) Load resistance (b) Firing angle (c) Average output voltage (d) The rms load voltage (e) The rms load current (f) DC power (g) AC power (h) Rectifier efficiency (i) Form factor (j) Ripple factorarrow_forwardTo find the Fourier series for the periodic function f(x) = 2 -2 when π < x < 0 - when 0 < x < πarrow_forwardDon't use ai to answer I will report you answerarrow_forward
- Don't use ai to answer I will report you answerarrow_forwardDisassemmble In another way f(t) = [sin(200πt) - cos(300πt)]2arrow_forward☑ 口 ☐ : Homework help starts here! Home | bartleby → https://www.bartleby.com Answered: Decompose using relationships 3 S(+) = 50 sin 3 (500πiz) | bartleby ASK AN EXPERT √ MATH SOLVER Decompose using relationships 3 S(+) = 50 sin 3 (500... Steps "Disassemble in another way." f(+)= 50 Sin³ (500+) Step 1 To decompose f(t)=50 Sin³ (500x+), use trigonometric indentity for Sin³ (e) Sin³ (0)- 3 Sin (e)-Sin (30) 4 Step2: Apply indentity to f(t). f(+)= 50 Sin³ (500+) = 50. 3 Sin (500+) - Sin (3*500π+) = 50. = = 12.5 4 3 Sin (500+)-Sin (1500+) 4 [3 Sin (580x+)-Sin (1500x+)] 37.5 Sin (500+)-12.5 Sin (1500π+) final decomposed form is, PM 05:2 19/12/2024 દ ))^ C W E × م اكتب هنا للبحثarrow_forward
- 6) The principal of DIT hire you to design PBAX with 120 phones. Assuming the number of call is 3/hour/line, the average call duration is 4 minutes, and 55% of all call are made external via a T-1 trunk (24 channels) to the PSTN. Determine carried traffic and channel usage.arrow_forwardNeed a solufor number 2arrow_forwardDecompose using relationships 3 S(+) = 50 sin ³ (500πiz)arrow_forward
- A linear electrical load draws I₁ A at a 0.72 lagging power factor. 11 = 153 When a capacitor is connected, the line current dropped to 122 A and the power factor improved to 0.98 lagging. Supply frequency is 50 Hz. a. Let the current drawn from the source before and after introduction of the capacitor be 1₁ and 12 respectively. Take the source voltage as the reference and express 11 and 12 as vector quantities in polar form. b. Obtain the capacitor current, Ic = I2 − I₁, graphically as well as using complex number manipulation. Compare the results. c. Express the waveforms of the source current before (i₁(t)) and after (i2(t)) introduction of the capacitor in the form Im sin(2лft + 0). Hand sketch them on the same graph. Clearly label your plots. d. Analytically solve i₂ (t) - i₁ (t) using the theories of trigonometry to obtain the capacitor current in the form, ic (t) = 1cm sin(2´ft + 0c). Compare the result with the result in Part b.arrow_forwardI need a solution from an expert without artificial intelligence. Choose the correct answer 1. The convolution of two signals in time domain is equivalent to (addition, subtraction, multiplication, division). 2. The Fourier transform of non-periodic signal is random). 3. In ASK). in frequency domain signal. (discrete, continuous, digital, the pulse location is proportional to the amplitude of the signal. (PAM, PWM, PPM 4. In TDM the input signals must have (the same maximum frequency, the same sampling frequency, the same bit rate, the same amplitude). 5. The Delta Modulation is equivalent to (1-bit DPCM, 2-bit DPCM, n-bit PCM, PSK). bandwidth when compared to the NRZ 6. In baseband digital transmission, the RZ signal has signal. (less, greater, equal, not related). 7. In Differential Manchester code, the shapes of "1" and "0" are, each other, next bit dependent, not related to each other). (the same, opposite to 8. In multi-level digital carrier system R, is _ R₁. (equal to, less…arrow_forwardI need a solution from an expert without artificial intelligence. Choose the correct answer: 1. In AMI code, the shapes of "1" and "O" are, bit dependent, not related to each other). 2. In FDM the guard band is used to decrease, maintain, not related to). 3. Higher number of levels in PCM produces (the same, opposite to each other, next the overlap between FDM signals. (increase, (higher quantization error, less number of bits per sample, lower quantization error, the same number of bits per sample). 4. If the maximum shift in frequency is 70 kHz and the minimum deviation in frequency of the actual signal is 109.93 MHz, what is the carrier frequency? (110 MHz, 110 kHz, 107 kHz, 102 MHz) Fc 5. TDM of signals requires them to have the same amplitude, sampling frequency, energy). 6. In standard AM, the last step in the transmitter is subtracting, multiplying, dividing). . In digital carrier systems, PSK). (maximum frequency, maximum the carrier signal. (adding, has higher bandwidth. (ASK,…arrow_forward
- Delmar's Standard Textbook Of ElectricityElectrical EngineeringISBN:9781337900348Author:Stephen L. HermanPublisher:Cengage Learning