b. A generating station supply two consumer I and 2 as follow: Time (Hours) Consumer 1 (kW) Consumer 2 (kW) midnight 4 a.m 50 100 4 a.m-6 p.m 180 6 p.m-8 p.m 0 8 p.m-10 p.m 10-midnight 300 250 120 0 500 Draw the daily load curve and find (i) load factor (ii) diversity factor (iii) plant use factor. 150

b. A generating station supply two consumer I and 2 as follow: Time (Hours) Consumer 1 (kW) Consumer 2 (kW) midnight 4 a.m 50 100 4 a.m-6 p.m 180 6 p.m-8 p.m 0 8 p.m-10 p.m 10-midnight 300 250 120 0 500 Draw the daily load curve and find (i) load factor (ii) diversity factor (iii) plant use factor. 150

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.16P: A single-phase, 120V(rms),60Hz source supplies power to a series R-L circuit consisting of R=10 and...

See similar textbooks

Similar questions

Please help with the solution.
Two generators are supplying a load. Both the generators have a no-load frequency of61.5 Hz and the slope sp of 1 MW/HZ. If they are supplying a real load of 2.0 MW at 0.8 pflagging, what would be the system frequency and power sharing between two generators?What measures can be taken to make the frequency 60 HZ. If an additional 1.0 MW load isconnected to the existing one what would the system frequency be.
The voltage regulation of an alternator having 0.75 leading p.f. load, no-load induced e.m.f. of 2400V and rated terminal voltage of 3000V is............... percent. *
Please help me
A generating station is to supply four regions of load whose peak loads are 10 MW, 5 MW, 8 MW and 7 MW. The diversity factor at the station is 2 and the average annual load factor is 60%. Calculate the the maximum demand on the station in MW.
two generators supplying a load. Generator I has a no-load frequency of 62.5 Hz and a slope Sp1 of I MW/Hz. Generator 2 has a no-load frequency of 62.0 Hz and a slope sp2 of I MW/Hz. The two generators are supplying a real load totaling 2.5 MW at 0.8 PF lagging. (a) At what frequency is this system operating, and how much power is supplied by each of the two generators? (b) Suppose an additional I-MW load were attached to this power system. What would the new system frequency be, and how much power would Gl and G2 supply now? Generator 1 VT V2 Generator 2 VTí KVAR KVAR
A non-sinusoidal quasi-square wave voltage v(t) is applied to a nonlinear load, resulting in a non-sinusoidal current i(t). The voltage and current waveforms are shown below. Assume any values of your choice for Vp (≤ 200 V) and Ip (≥ 5 A). 1. calculate the average power and net power factor of the load. 2. The total load harmonic distrotion (THD) of the load current, assuming the smallest frquency term as fundamental.
Two parallel loads are connected to a 120 volt rms, 60 Hz power line. One load absorbs 10 k watts at 0.8 power factor lagging. The second load absorbs 4 k watts at 0.9 power factor leading. Determine the real (watts) and reactive (VARS) power of the combined load.
A 500 MVA synchronous machine has H, = 5.6 MJ/MVA and a 1200 MVA machine has H₂ = 2.0 MJ/MVA. The two machines operate in parallel in a power station. What is the equivalent. H constant for the two, relative to a 100 MVA base?
A single-phase, 120V(rms),60Hz source supplies power to a series R-L circuit consisting of R=10 and L=40mH. (a) Determine the power factor of the circuit and state whether it is lagging or leading. (b) Determine the real and reactive power absorbed by the load. (c) Calculate the peak magnetic energy Wint stored in the inductor by using the expression Wint=L(Irms)2 and check whether the reactive power Q=Wint is satisfied. (Note: The instantaneous magnetic energy storage fluctuates between zero and the peak energy. This energy must be sent twice each cycle to the load from the source by means of reactive power flows.)
Consider two interconnected voltage sources connected by a line of impedance Z=jX, as shown in Figure 2.27. (a) Obtain expressions for P12 and Q12. (b) Determine the maximum power transfer and the condition for it to
For a power station the yearly load duration curve is a straight line from 50,000 to 4000 kw. To meet the load three turbogenerators are installed. The capacity of two generators is 20,000 kw each and the 3rd is rated at 7,000 kw. a. Draw the annual load duration curve b. Determine the following the Energy generated per year, Load factor and Annual Capacity factor.