A power station has to meet the following demand:Group A: 200 kW between 8 A.M. and 6 P.M.Group B: 100 kW between 6 A.M and 10 A.M.Group C: 50 kW between 6 A.M. and 10 A.M.Group D: 100 kW between 10 AM and 6 PM. and then between 6 P.M. and 6 A.M.Plot the daily load curve and determine (i) diversity factor (ii) units generated per day(iii) load factor.

Answered: Image /qna-images/answer/534c0459-496d-4548-8854-fa3b092cffbc.jpg

Answered: A power station has to meet the…

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.7P

See similar textbooks

Similar questions

A generator operating at 50 Hz delivers 1 p.u. power to an infinite bus through a transmission circuit in which resistance is ignored. A fault takes place reducing the maximum power transferable to 0.5 p.u. Where as before the fault, this power was 2.5 p.u. and after the clearance of the fault, it is 2 p.u. The value of 8 is max
step down chopper has Vs = 230 V and R = 10 0. For a duty cycle of 0.4, the power taken by the chopper is 2097 Watts. Find the chopper efficiency. Take the voltage drop across the chopper switch as 2 V. a) 98 % b) 89.96 % c) 99.14 % d) 96.54 %
A generating station is to supply four regions of load whose peak loads are10 MW, 5 MW, 8 MW and 7 MW. The diversity factor at the station is 1-5 and the average annual load factor is 60%. Then the installed capacity is (25 to26)MW. O (24 to25)MW. O (23 to24)MW. O
A 500 MVA synchronous machine has H, = 5.6 MJ/MVA and a 1200 MVA machine has H₂ = 2.0 MJ/MVA. The two machines operate in parallel in a power station. What is the equivalent. H constant for the two, relative to a 100 MVA base?
Two generators are supplying a load. Both the generators have a no-load frequency of61.5 Hz and the slope sp of 1 MW/HZ. If they are supplying a real load of 2.0 MW at 0.8 pflagging, what would be the system frequency and power sharing between two generators?What measures can be taken to make the frequency 60 HZ. If an additional 1.0 MW load isconnected to the existing one what would the system frequency be.
Show your detailed soln
A generation station of 3 MW supply a two region A & B .The load variation of these regions is as follow: Region A (Time) From midnight from 4a.m to From 10a.m to From 5p.m to to 4a.m 10a.m 5p.m 7p.m From 7p.m to midnight Load(kw) 800 500 NO load 300 100 Region B (Time) From From From From From midnight 6a.m to 2p.m to 4p.m to 9p.m to Load(kw) to 6a.m 300 2p.m 4p.m 9p.m midnight 600 No load 800 1100 With neglect transmission line losses. Find the load factor, diversity factor, reserve capacity,plant use factor.
Where did it come from?
Answer it i will thumbs up Dont copy paste..
Consider the switching waveforms shown below, operating with a duty-cycle of 30%. Which statements correctly describe the switching circuit, load and circuit operation? (Multiple answers possible, but wrong answers will deduct marks) Voltage across load Voltage (V) 000 120 0000 100 80 60 40 20 30 Time (us) The load must be predominantly resistive. The average current in the load is 1.0A. The RMS current in the load is approximately 1.414A. The load must be predominantly inductive. The resistive part of the load is 200ohms. The average current in the load is 0.6A. O The resistive part of the load is 50ohms. 0 0 10 20 40 50 60 Current (A) 2 5 0.5 0 0 10 Current through load 20 W 30 Time (us) 40 50 60
%VAI ۲,۷ K/s 9:- Zain 4.5G+ A step down de chopper is connected to an R-52 and L. 10 mH. The de supply voltage is 100 V. The chopper is switching at a frequency of 1 kHz with a duty cycle of 50%. Determine the load current, Jo and the peak to peak ripple current as an absolute value and as percentage of de value. ☐ О Δ
The peak load on a 50 MW power station is 39 MW. It supplies power through for transformers whose connected loads are 17, 12,9 and 10 MW. The maximum demands on these transformers are 15, 10, 8 and 9 MW respectively. The annual load factor is 50% and the plant is operating for 65% of the period in a year. 102. The average load on the station is (A) 50000 kW (C) 39000 kW (B) 19500 kW (D) 48000 kW. 103. The energy supplied per year is (A) 438 x 106 kWh (C) 170.82 x 106 kWh (B) 341.64 x 106 kWh (D) 420.48 x 106 kWh.

SEE MORE QUESTIONS

Recommended textbooks for you

Power System Analysis and Design (MindTap Course …

Electrical Engineering

ISBN:

9781305632134

Author:

J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:

Cengage Learning