A generation station of 3 MW supply a two region A & B .The loadvariation of these regions is as follow:Region A(Time)Frommidnightfrom4a.m toFrom10a.m toFrom5p.m toto 4a.m10a.m5p.m7p.mFrom7p.m tomidnightLoad(kw)800500NO load300100Region B(Time)FromFromFromFromFrommidnight6a.m to2p.m to4p.m to9p.m toLoad(kw)to 6a.m3002p.m4p.m9p.mmidnight600No load8001100With neglect transmission line losses.Find the load factor, diversity factor, reserve capacity,plant use factor.

Answered: Image /qna-images/answer/c3cad707-34f4-4fc8-be1d-ab2b00c99554.jpg

Answered: A generation station of 3 MW supply a…

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.61P

See similar textbooks

Similar questions

Please and thank you
A generator operating at 50 Hz delivers 1 p.u. power to an infinite bus through a transmission circuit in which resistance is ignored. A fault takes place reducing the maximum power transferable to 0.5 p.u. Where as before the fault, this power was 2.5 p.u. and after the clearance of the fault, it is 2 p.u. The value of 8 is max
An ac resistance is higher than a dc resistance. True False
The rms value of v(t)=Vmaxcos(t+) is given by a. Vmax b. Vmax/2 c. 2Vmax d. 2Vmax
A single-phase, 120V(rms),60Hz source supplies power to a series R-L circuit consisting of R=10 and L=40mH. (a) Determine the power factor of the circuit and state whether it is lagging or leading. (b) Determine the real and reactive power absorbed by the load. (c) Calculate the peak magnetic energy Wint stored in the inductor by using the expression Wint=L(Irms)2 and check whether the reactive power Q=Wint is satisfied. (Note: The instantaneous magnetic energy storage fluctuates between zero and the peak energy. This energy must be sent twice each cycle to the load from the source by means of reactive power flows.)
The temperature of a noninductive heater unit is controlled by a reactor. The heater unit and the reactor are connected in series across a 250 V, 60 Hz source. The voltage across the heater unit is 200 V. The voltage across the reactor is 100 V. The current in the circuit is 10 A. Determine: the power factor of the series circuit. the power factor of the reactor. the impedance of the reactor. the effective resistance of the reactor. the inductive reactance of the reactor
4) Therenin's Equinlena Circuit and Marimum Poer truns fer Thiorem a) For the Circuit derive the given in the figure, therenin's eq uivalence Circuit acrass the branch witn the loud impedanu. b) Culculate to deliver the volue of the load Impedanca makimum power to the load, c) caleula te the Power dissipa ted through the loud, 72
3- Please I want answer of this Electrical Principles question. Thanks
Calculate the rms values of load voltage and current for the circuit shown below. Please show work
Q4. The source current in the circuit shown is in Figure 3a) What impedance should be connected across terminals a,b for maximum average powertransfer?b) What is the average power transferred to the impedance in (a)?c) Assume that the load is restricted to pure resistance. What size resistor connected across a,bwill result in the maximum average power transferred?d) What is the average power transferred to the resistor in (c)?v
Please answer question in image with details on how to do it. Thank you.
Q3/A de shunt generator has a full load output of 10KW at terminal voltage of 220V. The sum of mechanical and core losses is 500W. Calculate the input power to the shaft and then determine the efficincy. Where Ra=0.602 and the Rf-16092 (30 mark)

SEE MORE QUESTIONS

Recommended textbooks for you

Power System Analysis and Design (MindTap Course …

Electrical Engineering

ISBN:

9781305632134

Author:

J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:

Cengage Learning