A balanced Y-connected load having an impedance of 96-j28 22 per phase is connected in parallel with a balanced A-connected load having an impedance of 144 +j42 2 per phase. The paralleled loads are fed from a line having an impedance of j1.5 Q2 per phase. The RMS value of the line-to-neutral voltage of the Y-connected input is 240V. a) Calculate the magnitude of the current in the line feeding the loads b) Draw the phasor diagram for input three-phase line voltages, and the line currents

A balanced Y-connected load having an impedance of 96-j28 22 per phase is connected in parallel with a balanced A-connected load having an impedance of 144 +j42 2 per phase. The paralleled loads are fed from a line having an impedance of j1.5 Q2 per phase. The RMS value of the line-to-neutral voltage of the Y-connected input is 240V. a) Calculate the magnitude of the current in the line feeding the loads b) Draw the phasor diagram for input three-phase line voltages, and the line currents

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.19P: Consider a single-phase load with an applied voltage v(t)=150cos(t+10)volts and load current...

See similar textbooks

Similar questions

Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor, and a 4 capacitor. (a) Draw the circuit diagram. (b) Compute the series impedance. (C) Determine the current I delivered by the source. Is the current lagging or leading the source voltage? What is the power factor of this circuit?
The instantaneous power absorbed by the load in a single-phase ac circuit, for a general R LC load under sinusoidal-steady-state excitation. is (a) Nonzero constant (b) Zero (c) Containing double-frequency components
A single-phase source has a terminal voltage V=1200volts and a currentI=1530, which leaves the positive terminal of the source. Determine the real and reactive power and state whether the source is delivering or absorbing each.
Consider a single-phase load with an applied voltage v(t)=150cos(t+10)volts and load current i(t)=5cos(t+50)A. (a) Determine the power triangle. (b) Find the power factor and specify whether it is lagging or leading. (c) Calculate the reactive power supplied by capacitors in parallel with the load that correct the power factor to 0.9 lagging.
Clear and correct or dislike
The circuit shows an unbalanced electrical installation powered by a positive sequence symmetrical three-phase network of 380 V compound voltage. The loads are single phase. Load 1 absorbs an active power of 950 W with f.d.p. 0.5 inductive. Load 2 absorbs an active power of 1,140 W with f.d.p. Unit. Load 3 absorbs from the network an active power of 760 W with f.d.p. 0.5 capacitive. Taking the network voltage URN as the phase reference, calculate: a) complex expressions of the line currents IR. Is. and IT
The circuit shows an unbalanced electrical installation powered by a positive sequence symmetrical three- phase network of 380 V compound voltage. The loads are single phase. Load 1 absorbs an active power of 950 W with f.d.p. 0.5 inductive. Load 2 absorbs an active power of 1,140 W with f.d.p. Unit. Load 3 absorbs from the network an active power of 760 W with f.d.p. 0.5 capacitive. Taking the network voltage URN as the phase reference, calculate: a) complex expressions of the line currents IR. Is. and IT RO- SO TO IR Is IT U₁-380 V CARGA 1 P₁ =950 W cos p1=0,5 ind. CARGA 2 P₂=1.140 W cos p₂=1 CARGA 3 P3=760 W cos p3=0,5 cap.
8. The total power supplied to a balance delta load is found in the same way as for a balance wye load. True False Either Neither 12. A load of 20 + j35 ohms is connected across a 220 V, 60 Hz supply. Find the reactive power of the load in var. 595 2420 1042 1382 13. A type of DC source where the characteristic output voltage has perfect unidirectional waveform and is based on electrochemical principle. Generator Inverter Converter Battery 14. Calculate the Rf of a circuit whose impedance is 20+j35 and current of 2A. 0.86 0.91 0.50 0.71 15. What capacitor shall be installed in parallel with a circuit to achieve a unity power factor if the reactive power of a circuit is 200VARS and the voltage is 100V. 80.45 microfarad 53.05 microfarad It's already in unity 62.45 microfarad
Question 6 20020°V L rms In the circuit in the figure; L load draws 15 kVA with lagging power factor 0.6. • The load L 2 draws 6 kVA with a leading power factor of 0.8. According to this; What is the value of the reactive power for the loadL ? 1 9000 O -3600 O 2700 O 12000 O 4800 O 4500 No new data has been saved. The latest contact is at16I01
Slove this question according to figure 04. Find the Thevenin equivalent circuit looking from the terminals a-b as shown in Figure 04. In Figure 04, assume that the load is purely resistive (RL), determine the value of the load resistor RL across terminals a-b for maximum average-power transfer, and calculate the RMS value of the load current when RL is connected between terminals a-b. Calculate the complex power drawn by the load when RL is connected between terminals a-b.
Do aprr c ,d and e
If a A-connected load has a balanced impedance ZA 94 - 17° 2 and a voltage = = / VBC = 265 82° V rms, what is the magnitude of the current Ia (in A rms)? C V cn Van a Answer: n Von b Ia Ib 20 B IAB IBC ZA ZA ICA C