37. Sensors are used to monitor the pressure and the temperature of a chemical solution stored in avat. The circuitry for each sensor produces a HIGH voltage when a specified maximum valueis exceeded. An alarm requiring a LOW voltage input must be activated when either the pres-sure or the temperature is excessive. Design a circuit for this application?

Answered: Image /qna-images/answer/57aace0e-93f3-4a5a-9d92-8a42376fd9fe.jpg

Answered: 37. Sensors are used to monitor the…

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter29: Dc Generators

Section: Chapter Questions

Problem 20RQ

See similar textbooks

Similar questions

A voltage regulator is a device that maintains a fix what?
I have an O Gauge track and would like to convert it into a “sensored” track. Additionally, I would like to connect that track to an ESP-WROOM-32 board that should flash an LED whenever the track detects a non-moving train. Please list all the components (and how many of each) needed. Also, what’s the procedure for connecting the components?
The process shown in Figure 1 is to be used to control the level of water in a storage tank by turning a discharge pump on or off. The modes of operation for which programming is required are as follows: Pump running Low level High level ON/OFF High sensor switch MANAUTO Low sensor switch Pump motor Figure 1: The process used to control the level of water in the storage tank OFF Position -The water pump will stop if it is running and will not start if it is stopped. Manual Mode -The pump will start if the water in the tank is at any level except low. Automatic Mode -If the level of water in the tank reaches a high point, the water pump will start so that water can be removed from the tank, thus lowering the level. When the water level reaches a low point, the pump will stop. Status Indicating Lights -Water pump running light (green) - Low water level status light (red) - High water level status light (yellow) Provide the allocation list and the ladder logic program for the above…
Q/ This means clarifying and indicating with I needd adrawind, anhotation and explanation of a picture Power Stage B IM A conduction Analog Interface Circuit To the gates. 介 Firing Circuit Micro-Controller Circuit C (A) fring angle (B) 30 firing angle (C) 90 firing angle (D) 120° fring angle Figure 7 Electronic Soft Starting & Effect of Firing Angle on Output Voltage
Draw a simple pulse detector (positive-edge) diagram and explain how it works.
15 - Which of the following is not one of the advantages of the inductive proximity sensor over the limit switch? A) It is small in size.B) They can be used in potentially explosive places.C) They make contact perception.D) It has no moving parts.E) There is no contact problem.
Question 9
How do you erase an EPROM if you've never done it before?
I have a wooden toy train that runs on wooden tracks. I would like to place two ESP-WROOM-32 Boards on top of the train. Broadcast communication (which involves radio frequency, not Wi-Fi) would help communicate about the train's lateness to five other wooden trains on the same track. Local communication would help communicate to the train station about the train's lateness. I would also need radio frequency Tx-Rx Modules for discharging and undergoing the signal, and repeaters just in case the signal loses power due to long-distance traveling. My wooden train should be automated. It should run at 4 inches per second, keep a minimum distance of 30 seconds away from the other wooden trains, and make a 17-second-long stop every 500 seconds. What's the procedure to connect the components? What's the Arduino code (C++) for this project?
How do microchips play a vital role in various electronic devices and applications?
6. Draw a comparator circuit to turn on an LED when the input voltage exceed 5 volts.
Which of the following statements is true for an SCR. O A. It is an on-only controllable switch, which is turned on by a gating signal and cannot be turned off externally; only system conditions can turn off the device once it is on O B. None of the other choices are correct O C. It is a controllable switch, which is turned on by applying a gating signal and is turned off when the gating is removed O D. It is an off-only controllable switch, which is turned off by a gating signal as needed O E. It is an on-off controllable switch, which is turned on and off by a gating signal as needed

SEE MORE QUESTIONS

Recommended textbooks for you

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS