The voltage divider was set up with two 1 , 0 0 0 � resistors, then the function generator was set to produce an open - circuit voltage of 2 � � � at 1 0 kHz . The oscilloscope was set to trigger on the rising edge of the Channel 1 waveform at a trigger level of + 0 . 5 V to produce the waveform shown in Figure 5 . Figure 5 . Waveform for which the voltage equation of time was computed. The equation of this voltage waveform is � ( � ) = complete the equation Please find the equation of the voltage wave form

The voltage divider was set up with two 1 , 0 0 0 � resistors, then the function generator was set to produce an open - circuit voltage of 2 � � � at 1 0 kHz . The oscilloscope was set to trigger on the rising edge of the Channel 1 waveform at a trigger level of + 0 . 5 V to produce the waveform shown in Figure 5 . Figure 5 . Waveform for which the voltage equation of time was computed. The equation of this voltage waveform is � ( � ) = complete the equation Please find the equation of the voltage wave form

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter21: Resistive-capacitive Series Circuits

Section: Chapter Questions

Problem 7RQ: An RC series circuit is connected to a 120-V, 60-Hz power source. The resistor is 25 and has a...

See similar textbooks

Similar questions

If the charging resistor was twice as large as the discharging resistor in Figure 4, theamplitudes of the charging and discharging waveforms would be ________.a. The sameb. Different
Suppose you are asked to generate the waveforms as shown in figure 1, continuous over time, using the 555 timer. Assume that period of all the waveforms are 4ms. Draw the clear circuit diagram required for the generation of each of these waveforms and calculate the values of resistors and capacitors to be used.
lease draw the same sine wave that would be displayed on different time per division and volts per division settings on the oscilloscope. the time per division is displayed at the center bottom of the each screen and the volts per division is displayed on the bottom left of the screen. The wave you will be drawing will be a sine wave with frequency of 1000 Hz and an amplitude of 3 V. The wave you will be drawing will have the equation: 3sin(2π⋅1000t)
VI. Homework: 1. Sketch the output waveforms expected when a sine wave (100 Hz, 15V) is applied to cach of the circuits shown in the figure. Specify important voltage levels and time scales. The input is on the left and the output is on the right. 10 ka 立 IN4735 6.0 V IN4007 IN4007 10 ka V IN4007 10 kn IN4007 A IN4007 SOV 3.0V T 30
Please answer correctly and I will upvote. Thank you.
Identify which measurement this oscilloscope time difference reading is useful for. Oscilloscope-XSC1 Time 250.000 us 1.261 ms Channel_A 169.064 V 168.513 V -550. 584 mV Channel_B 89. 282 V 95.005 V 5.722 V Reverse T2-T1 1.011 ms Save Ext. trigger Timebase Scale: 200 us/Div : Scale: 100 V/Div X pos. (Div): 0 Channel A Channel B Scale: 100 V/Div Y pos. (Div): 0 Trigger Edge: F Level: 0 A B Ext Y pos. (Div): 0 V Y/T Add B/A A/B AC DC AC DC Single Normal O period O none of the above O phase shift
The initial rate of current rise in an RL circuit is 300 amp per sec when 120 volts is suddenly impressed. What is the inductance of the circuit?
QUESTION Two signal measured using oscilloscope as shown in Figure 1. From the result shown in ocilloscope detemine the peak to peak voltage and the phase difference between two waveforms. Oscilloscope XSC1 VOLTS DIV TIME/DIV ms 5 10 50 20 20 50 10 mv 20 Figure 1
Identify which measurement this oscilloscope time difference reading is useful for. Ociloscope-XSC1 Channel_A 169.064 V 168.513 V Channel_B 89.282 V 95.005 V Time Reverse 250.000 us 1.261 ms 1.011 ms T2 T2-T1 -550. 584 mV 5.722 V Save Ext. trigger Channel A Timebase Scale: ko0 us/Div X pos. (Div): 0 Y/T Add B/A A/B Channel B Trigger Scale: 100 V/Div Y pos. (Div): 0 AC0 DC 100 V/Div f 2 AB Ext Scale: Edge: | Y pos.(Div): 0 AC 0 DC Level: V Single Normal Auto None
looking for assistance
An RC series circuit is connected to a 120-V, 60-Hz power source. The resistor is 25 and has a voltage drop of 65 volts. What is the capacitance of the capacitor?
Draw the charging and discharging waveform if the switch changed position precisely when the capacitor reached 5 time constants when charging and discharging.