Modern control engineering 4th edition: I would like to understand the detailed method for solving this equation. Thank you in advance for your answer. R(s)G₁Hyst1+H+G-IGGH+G_Gif(H₁G3+G2G3)1+H2G2 H1G3H3+G2G3H3G₁C(s)R(s)=1+G(1+H2G2 H1G3H3+G2G3H31C(s)R(s)=(H1G3+G2G3)(H1G3G1 G2G3G1)1+H2G2+H1G3H3+G2G3H3+H1G3G1+G2G3G1C(s)

Answered: R(s) G₁ Hyst 1+H+G-IGGH+G_Gif…

R(s) G₁ Hyst 1+H+G-IGGH+G_Gif (H₁G3+G2G3) 1+H2G2 H1G3H3+G2G3H3 G₁ C(s) R(s) = 1+G( 1+H2G2 H1G3H3+G2G3H31 C(s) R(s) = (H1G3+G2G3) (H1G3G1 G2G3G1) 1+H2G2+H1G3H3+G2G3H3+H1G3G1+G2G3G1 C(s)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

a. It is necessary for control system to meet certain specifications as far as its performance is concerned. Explain the methods (at least three) that can be employed to improve the time response of a control system. uinment that buuiro
Please solve it quickly
Which one is not a true statement a. Feedback can bring oscillations in response b. Open loop systems are generally stable c. Automatic Control Systems are generally stable in nature d. Care required to design a stable closed loop system
explain analog control and digital control. What are the main differences between them? give an example from daily for each of them.
-- A force sensor system is given in figure. The force squezes a spring (with K=100N/mm) through a massless piston which is connected to wiper of 500-Ohm linear potentiometer with sensitivity of 8 Ohm/mm. The potentiometer input (supply) voltage is 1Voc and the output is propotional to force via sensing setup. The spring displacement (y) is measured from its initial (F=0) positon. The force measurement is displayed on a computer screen. -Ireut Valtege- 6 +5)*100] to www sing Centect (b) The force applied to spring is changes from [{ 6 +10)*400] Newtons. Design required amplifier circuit(s) for scaing the force range voltage output to 0 to 5V., . Outpet varege
Re design the system below into Closed-loop control of the speed of a turntable. Draw the block diagram model. Battery Speed Turntable www DC DC motor amplifier (a) Control device Actuator Process (a) Open-loop (without feedback) control of the speed of a turntable. (b) Block diagram model. Desired speed (voltage) Amplifier DC motor Turntable Actual speed (b) To obtain disk rotation, we will select a DC motor as the actuator because it provides a speed proportional to the applied motor voltage. For the input voltage to the motor, we will select an amplifier that can provide the required power. The open-loop system (without feedback) is shown in (a). This system uses a battery source to provide a voltage that is proportional to the desired speed. This voltage is amplified and applied to the motor. The block diagram of the open-loop sys- tem identifying control device, actuator, and process is shown in (b). Speed setting
Please solve all parts otherwise down vote
In swimming pools and water tanks, the water level needs to be controlled. To manage the water level, a water level controller device is used. The aim of water level controller is to adjust water flow and improve the functioning. For the water level closed loop system shown in figure Q4, analyze the following basic components of the system: (1) Controlled variable (ii) Reference variable (ii) Comparison element (iv) Error signal (v) Control unit Hollow ball Lever Water input Pivot
Manufacturing a motor for electric scooter. What is the tolerance in manufacturing a motor for electric scooter?(The precision required in motor manufacturing)
List and explain elaborately 10 limitations and 10 advantages you currently foresee in the field of mechatronics.
It is aimed to implement an automatic test system to be used in a laboratory environment in order to perform comprehensive functional tests to be used in the development and verification stages of an avionic control unit. To meet below needs, a programmable/automatic test equipment/system is required. REQUIREMENTS OF THE PRODUCT TO BE TESTED The features expected from the test system (TS) to be designed are listed below: V TS will be able to supply 28Vdc 5A power to the Product to be Tested. V TS must be able to separately read 2 analog output signals coming from the Product to be Tested. The output characteristics of the analog channels of the Product to be Tested are described below: • 3.3V Amplitude • 1.65V Offset • 250kHz sine wave V TS will be able to operate by generating pulse or continuous square wave signals to 8 digital inputs of the Product to be Tested. The amplitude voltage level is 12V. The smallest pulse width duration is 1 ms. V TS will be able to send messages over the…
Q3) Specify "yes" or "No" for the following: Yes No A- HVAC is abbreviation of heat, ventilation and air conditioning system. Yes No B- A controller is direct- acting when an increase in the level of sensor signal results in decrease in the level of controller output. Yes No C- Bellow is pressure sensing element. Yes No D- Hygroscopic materials can't change its size in response to change in humidity. Yes No E- Control relays are designed to carry low-level of temperature.