(B) Calculate the amount of reinforcement for the concrete basement of water tank shown using ACI and BS approaches if 1- Min reinforcement is required 2- Use flexural steel ratio = 0.032 Reinforced Concrete Basement Well Compact Soll -700mm->>

(B) Calculate the amount of reinforcement for the concrete basement of water tank shown using ACI and BS approaches if 1- Min reinforcement is required 2- Use flexural steel ratio = 0.032 Reinforced Concrete Basement Well Compact Soll -700mm->>

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter9: Composite Construction

Section: Chapter Questions

Problem 9.3.1P

See similar textbooks

Related questions

Q: What is the shear force to be carried by the reinforcements of a beam subjected to axial tension if…

Q: What is the threshold torsion (kN-m) of a rectangular beam with a width of 403 mm and an over-all…

A: Given Data: The width of a rectangular beam is b=403 mm. The overall-depth of a rectangular beam is…

Q: Question 1 Design a square shape reinforced concrete colunn to withstand the following dead and live…

A: Square Column: This is the most commonly used in the construction of buildings. It is very easy to…

Q: For parallel non prestressed reinforcement in a horizontal layer, clear spacing shall be at least…

A: For parallel non-prestressed reinforcement in a horizontal layer, clear spacing shall be at least…

Q: Problem 1: Calculate Mn and check the minimum steel limit f'c = 4 ksi, fy = 60 ksi. 2.5" 25" 6-#9…

A: Analysis of T-beamf'c=4 ksify = 60 ksi

Q: Table 5: Compressive strength Grade of Specimen Maximum load (kN) concrete 7 days 14 days 28 days…

A: Compressive strength =maximum loadarea Average/ Mean compressive strength=sum of compressive…

Q: For pretensioned axially tensioned member, how to calculate the effective prestress established in…

A: 1. The stress remaining in the concrete due to prestressing after the loss of prestress.2. Loss of…

Q: Calculate the target mean compressive strength at 28 days curing, for M20 grade concrete, as per IS…

A: Given- M20 grade of concrete, Standard deviation- σ=4 N/mm2

Q: Q3- Three concrete beams were selected for flexural strength test. Results from tests are shown in…

A: NOTE - Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the…

Q: 1) Examples of standard steel shapes include? a) Brick, CMU, concrete block b) Z-ties, corrugated…

Q: If for a Class T beam the concrete strength at transfer and before losses is 4000 psi, and the…

A: To calculate the allowable compressive stress at transfer and before losses for Class T beam.…

Q: Item 2 A. Calculate the stress in the concrete at the top and bottom extreme fibers under a positive…

A: Given data, A ) M= 78 kip B) f'c = 3200 psi l = 26 ft

Q: A half-block concrete masonry unit is tested for compressive strength. Theoutside dimensions of the…

A: Given:- Outer size of specimen = 190 mmm * 190mm * 190mm Wall thickness = 25mm Maximum load = 225kN…

Q: If the compressive strength of the concrete is 4 ksi and the yield strength of steel is 60 ksi, the…

Q: 1. What component of concrete that has affect its strength largely? Explain. 2. If you have to…

A: Note- Hi! Thank you for the question, As per the honor code, we are allowed to answer three…

Q: A normal-weight concrete has an average compressive strength of 20 MPa. What is the estimated…

A: Given data: Average compressive strength of concrete is 20 MPa. Determine the flexure strength=?

Q: 1. Which of the following is the compressive strength of concrete if β1=0.65. a) 60 MPa

A: compressive strength of concrete= 21Mpa

Q: A rectangular beam with a width of 8 in., an effective depth of 1ð in., and a total depth of 12 in.…

A: Given:- b=8 in h=12 in d=10in f'c=6000 psi fu=140ksi Eg=7800000psi To find:- nominal flexural…

Q: 1.) Given the following properties of a rectangular concrete beam: b = 280mm, d = 480 mm, f'c = 21…

Q: A simply supported beam shown in figure 1, carries an uniform service (unfactored) superimposed…

A: Given: fc'=3500 psify=60000 psi

Q: a. The flexure strength of the concrete if center-point was applied. b. The flexure strength of the…

A: A)The flexure strength of the concrete if center-point was applied. Given data, b=0.15 m d=0.15 m…

Q: A 450 diameter concrete spiral column is to be desigmed to support a factored axial load of 3200 kN.…

Q: A rectangular beam with a width of (9536/1150)-in,and effective depth of (9536/900)in is Reinforced…

A: The shear force is a surface-sensitive force. The reaction that is induced in a structural element…

Q: AT-beam behaves as a rectangular beam of a width equal to its fange if its neutral axis OA. Remains…

A: Using stress diagram

Q: . A split-tension test was conducted on a concrete cylinder with a 150 mm diameter and 300 mm…

Q: Determine the values of a, c, and E, for the beam shown in the figure. fy = 415 MPa and f = 23.7 MPa…

A: Determine the values of a, c, and tensile strain for the beam

Q: Considering the nominal shear stress on concrete is fy = 0.83 MPa. Calculate the allowable max…

Q: A post-tensioned prestressed concrete beam is to carry an intermittent live load of 1000 lb/ft and…

A: Given:- intermittent live load=1000 lb/ft superimposed dead load=500 lb/ft f'c=6000 psi To find:-…

Q: What is the value of the Whitney stress block parameter, β1β1, for 6000 psi concrete?

A: To find :- Whitney stress blovk parameter B1 for 6000 psi concrete

Q: A half-block concrete masonry unit is tested for compressive strength. Theoutside dimensions of the…

Q: Given Data: Concrete dimensions Area of steel 625 560 f = 30 MPa 3HD25 f, = 420 MPa %3D A, = 2457…

A: Given -

Q: AT beam has a concrete and steel strengths of 28 MPa and 420 MPa. The live load is (3830 + last 3…

Concept explainers

Design criteria for structural loading

The different loads such as loads due to self-weight (dead load) and external loads such as live load, wind loads, seismic load, snow load, and other loads and load combinations that influence the design of a building are called structural loading. The nature of the applied load differs from changes in the location, design, and type of materials used. The design criteria require that structures must be designed and constructed to be able to withstand all load types that are expected to act upon the structure and render its usage for the designated purpose. The structural members such as beams, slabs, columns, and foundations help the structure to withstand the applied load. There are different institutes such as ASCE and ACI that provide building design codes to assure minimum safety requirements and quality of the structures.

Question

(B) Calculate the amount of
reinforcement for the concrete
Roihfordad Conerete Basemont
basement of water tank shown using
ACI and BS approaches if
Well Compact Soll
1- Min reinforcement is required
2- Use flexural steel ratio = 0.032
wwo0L->

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given:

Step 2: ACI method:

Step 3: BS method:

Solution

Step by step

Solved in 4 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Pls I need a complete solution ✅ using Bond Stress development length hook and splicing of reinforced In RCD. THANK U...
Give me right solution
A simply supported beam (Span = 25 ) has a seetion as shown below with normal-weichs concrete compressive strength fc- 4000 psi (normal weight, and steel reinforcement,fy=40,000 psi 1- find the modulus of rupture of the concrete per ACI318-10 2- find gross section properties to calculate the crracking bending moment (Mcr) 3-check whether the cross section is over -or under -reinforced 4-caclculate the nominal flexural strength of the cross section (Mn)
A beam having a width of 500 mm and a total depth of 800mm is reinforced with 6-32mm dia bars Compressive strength of concrete is 28 MPa and yield strength of reinforcing bars is 420MPaa) depth of the compression blockb) strain in the tension reinforcementc) moment reduction factor
Answer Options Correct Q.No Question/Statement Answer A Select the grade of concrete required for 1 М5 M50 M15 М80 airport runways. The load which has fixed size and location is 2 called as Environmental All answers Dead load Live load Load are wrong Top surface of the tensile Bottom The clear cover of the RCC beam is taken as Centre of surface of the Bottom of the gravity of the tensile steel vertical distance from the base of the beam to steel tensile steel beam the reinforcement reinforcement 4 Stocky column generally fails by_ Compression Tension Buckling Deflection In a one way slab the main reinforcement is provided along All answers Both long and short span Long span Short span are wrong All answers Flat slab is placed above Drop panels Column Column head are correct The maximum percentage of reinforcement in 7 RCC short column, based on practical 0.8% 4% 6% 2% difficulties is For reinforced concrete wall D4B When to columns are far, select the type of foundation Trapezoidal…
Number 1 (parts i, ii, iii) please :)
i need the answer quickly
A 450 diameter concrete spiral column is to be desigmed to support a factored axial load of 3200 kN. Clear bar covering is 40 mm and the aggregate size is 25 mm. Use the 2010 NSCP with fc= 28 MPa, fy = 415 MPa, fyt = 415 MPa. Limit the gross steel percentage to 2%. Find the following a) The mumber of pcs of 28 mm diameter bars for the longitudinal reinforcements. b) The spacing of the 10 mm diameter spiral reinforcements in mm. c) Which of the following mostly nearly gives the clear spacing of the main longitudinal reinforcements in mm.
2. Tensile strength of concrete is about: (20-35)% of compressive strength (45-70)% of compressive strength None of the above. Tension controlled section Balanced section Compression-controlled section 4- The reduction factor (0) is equal to 0.9 if the: Es 2 Ety + 0.003 Es S Ety + 0.003 Es Ety 5- The design method which use the factored loads is - Working stress method - Ultimate design Method - None of above 6- If p< Po therefore the section is - Under reinforced - Over reinforced - None of above
Given a beam section b angle D = 450mm * 950mm M*=1500kNm, f_{c}' = 32MPa f_{5y} = 500MPa and the maximum aggregate size=20mm. Design and detail the section. Use N28 bars for the main reinforcement and R10 bars for stirrups. Exposure classifi-cation A2 applies. Please don't hand writing
Determine the cracking moment (KN/M) and compressive stress felt by concrete (MPa). Show your solutions
The material of the bcam given below is C35-45- B50OC and it is good quality concrete. The cobcreie cover is gIYCD as 50 mm. Thc dimensions of the bcam are gven as be820 mm. bw:350mm.t130 m, b 700 mm. Tbe sbear force (Vd)is S50 EN and stirrup calcelations will be done in the span region othe beam. Ir 338 stirupis used to mcet the shear force, what is the maximum stimup spacing (cm) in span region? (s=2) 11 15 D13 017 Boş bırak Sonraki> Kapat