A reinforced concrete tie has a square cross section of 8 in. × 8 in. and is reinforced with 8 # 5 steel reinforcing bars Grade 60. If the concrete has a 28-day compressive strength of 4000 psi , calculate the cracking and factored tensile forces that can be supported by the tie.

A reinforced concrete tie has a square cross section of 8 in. × 8 in. and is reinforced with 8 # 5 steel reinforcing bars Grade 60. If the concrete has a 28-day compressive strength of 4000 psi , calculate the cracking and factored tensile forces that can be supported by the tie.

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter11: Fracture And Fatigue

Section: Chapter Questions

Problem 11.4P

See similar textbooks

Related questions

Q: Why is reinforcing steel used in concrete? Discuss the typical properties ofreinforcing steel.

A: Reinforced concrete is used in concrete to make the structure very strong, and also to increase its…

Q: How to get the value of compressive strength of concrete f'c, given the nominal shear stress on…

A: given nominal shear stress on concrete-fv=0.88 MPato find-compressive strength of concrete f'c

Q: Calculate the tensile steel stress of 5-20-mm-dia rebars in a concrete beam 270 mm by 410 mm at…

Q: A symmetrical cross-section of a reinforced concrete shown has a value of f'c = 26.27 MPa and fy =…

A: Given data f'c = 26.27mpa fy = 414 mpa The As value was not given. so lets assume as 3bars of 32mm…

Q: A. Write a detailed note on stress-strain characteristics of reinforced concrete and steel. B.…

A: A) The tensile strength of concrete as compared to compressive strength is very weak, it can only…

Q: The maximum applied load on a cylindrical concrete specimen of diameter 150 mm and length 300 mm…

A: Given data- Diameter of the specimen D=150 mmLength L=300 mmLoad P=157 kNTo Find-The split tensile…

Q: o Why the tensilę strengths of concrete are of the order of 10 and 15%of the compressive'strength.

Q: Calculate the tensile steel strain of 5-16mm-diameter rebars in a concrete beam 240 mm by 420mm at…

Q: 7.8 Design the concrete mix according to the following conditions: Design Environment Building frame…

A: Required design strength of the concrete mix = 27.6 MPaStandard deviation of compressive strength =…

Q: The bond strength for M20 concrete as per IS 456: 2000 is 1.2 N/mm2. For reinforcing steel of grade…

Q: Q- The maximum applied load on a cylindrical concrete specimen of diameter 150 mm and length 300 mm…

Q: Problem 1: Transformed Moment of Inertia and Elastic Deflection Given: The center of the top and…

A: If any structure consists of more than one shape and is made up of more than one material then it is…

Q: A 3 m concrete column 300 mm in diameter is reinforced with 5 - 15M steel rods (reinforcing bars).…

A: Given: Diameter of the column D=300 mmarea of column A=π4×D2=π4×3002=70685.83 mm2Area of the…

Q: 2. Based on stress-stain relationship of concrete for nonlinear structural analysis, please provide…

Q: Compressive strength test is a mechanical test measuring the maximum amount of compressive load a…

A: The above Question is about Compressive strength determination using CTM ( compressive testing…

Q: Consider the following strengths of concrete: 1. Cube strength 2. Cylinder strength 3. Split-tensile…

Q: Column AB is made from high strength pre-cast concrete and reinforced with four in diameter A-36…

A: Given : To Find : Pmax = ?

Q: According to Section 10.2.3 of AC, the maximum usable strain at extreme concrete compression fiber…

A: According to Section 10.2.3 of AC, the maximum usable(ultimate) strain at extreme concrete…

Q: 2. The side of a concrete cube is: 15 cm The load at the time of breaking the cube: P kN. Calculate…

Q: c) Find the stresses in the concrete and the reinforcement for the following applied moments: (i) -…

A: Given:b=300 mmh=520 mmEc=30 GPaEs=200 GPad=460 mmAs=1470 mm2 Modular ratio has to be determined.…

Q: . A split-tension test was conducted on a concrete cylinder with a 150 mm diameter and 300 mm…

Q: Item 1 A. Compute the bending stress in the extreme compression fiber of the beam in the figure for…

Q: Maximum strain in concrete taken for design is 0.0040 while strain in deformed bar is calculated…

Q: What is the value of the Whitney stress block parameter, β1β1, for 6000 psi concrete?

A: To find :- Whitney stress blovk parameter B1 for 6000 psi concrete

Q: What is the dimension b and d of the specimen in mm?

A: given= a concrete specimen with equal sides having a span of 600mm and carrying a load of 100kn.…

Q: Q.11 The bond strength for M20 concrete as per IS 456: 2000 is 1.2 N/mm2. For reinforcing steel of…

A: Given data- Grade of concrete M20Bond strength τbd=1.2 N/mm2Grade of steel Fe 360To Find-The…

Q: The grains of wood in the board make an angle of 20° with the horizontal as shown. The board is…

A: Given- P=300 KN σy=0τxy=0

Q: A. Calculate the stress in the concrete at the top and bottom extreme fibers under a positive…

Concept explainers

Design criteria for structural loading

The different loads such as loads due to self-weight (dead load) and external loads such as live load, wind loads, seismic load, snow load, and other loads and load combinations that influence the design of a building are called structural loading. The nature of the applied load differs from changes in the location, design, and type of materials used. The design criteria require that structures must be designed and constructed to be able to withstand all load types that are expected to act upon the structure and render its usage for the designated purpose. The structural members such as beams, slabs, columns, and foundations help the structure to withstand the applied load. There are different institutes such as ASCE and ACI that provide building design codes to assure minimum safety requirements and quality of the structures.

Question

Expert Solution

Step 1

Given data:

Step 2

Calculate the area of steel and gross area:

Step 3

Calculate P_n:

Trending now

This is a popular solution!

Step by step

Solved in 5 steps with 5 images

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The square cross section of a reinforced concrete tie is 8 in. x 8 in., and it is reinforced with 8 # 5 steel reinforcing bars Grade 60. Calculate the cracking and calculated tensile stresses that the tie can withstand if the concrete has a 28-day compressive strength of 4000 psi.
Which strain and stress profiles shown in the figure below best represent a reinforced concrete section subjected to flexure at the ultimate limit state?
The boards for a concrete form are to be bent into a circular shape having an inside radius of 10 m. What maximum thickness can be used for the boards if the normal stress is not to exceed 7 MPa? Assume that the modulus of elasticity of the wood is 12 GPa.
Q- The maximum applied load on a cylindrical concrete specimen of diameter 150 mm and length 300 mm tested as per the split tensile strength test guidelines of IS 5816:1999 is 157 kN. The split tensile strength (in MPa, round off to one decimal place) of the specimen is?
NO 1 Please solve and answer correctly, give the complete solutions.
Determine the tensile steel ratio of a singly reinforced concrete beam for the following conditions using concrete strength f'c = 21 MPa and steel yield strength fy = 420 MPa a.) if the tensile strain is es = fy/Es upon crushing of concrete at a strain of 0.003 b.) if the tensioe strain is set as 0.009 upon crushing of concrete at strain of 0.003 c.) minimum as required by NSCP 2015
9. If the value of the fc' of concrete is 30 MPa, and the actual stress of the concrete subjected to a force is 12 MPa, at what stage is the concrete at?
The flexural tensile strength of M25 grade of concrete, in N/mm², as per IS:456-2000 is A 0.5 B 5 C 2.25 D 3.5
CASE:A rectangular beam has the dimensions (see Fig.1) b = 15 in.,h = 30 in., and d = 27.37 in. and is reinforced with three No.9 bars. The concrete compressive strength fc' is 4000 psi, and the tensile strength in bending (modulus of rupture) is 475 psi. The yield point of the steel fy is 60,000 psi, the stress-strain curves of the materials being those of Fig.2. Determine the stresses caused by a bending moment M = 45 ft-kips.Question1:Check this case, would the concrete of the beam crack? Please calculate the strengths of those two materials in this beam.Question2:Suppose the beam under this case is subject to a bending moment M = 110 ft-kips (rather than45ft-kips as previously). Calculate the relevant properties and stresses.Question3:Determine the nominal moment Mn at which the beam of this case will fail. Question4:Have a comparison of the calculation results with those of three questions.
The concrete in the core of a spiral column is sub- jected to a uniform confining stress o, of 680 psi. What will the compressive strength o be? The un- confined uniaxial compressive strength is 5000 psi.
Stress and strain analysis
Reinforced concrete