Q3- Three concrete beams were selected for flexural strength test. Results from tests areshown in table below. If the flexural strength of the concrete is 1505 KPa, determine theload needed for failure in each test using four points loading. Show the detailedcalculations and loading system sketches.S.NWidth, mmDepth, mmSpan, mm(Width +18 (Depth +0.5x18 (Span +181149.2148.4471143.3146.84663137.6137.1450

Answered: Image /qna-images/answer/4d276613-b488-4d92-a0cc-7eaf2f84b937.jpg

23- Three concrete beams were selected for flexural strength test. Results from tests are hown in table below. If the flexural strength of the concrete is 1505 KPa, determine the pad needed for failure in each test using four points loading. Show the detailed alculations and loading system sketches. S.N Width, mm Depth, mm Span, mm (Width +18 (Depth +0.5x18 (Span +18 149.2 148.4 471 143.3 146.8 466 3 137.6 137.1 450

23- Three concrete beams were selected for flexural strength test. Results from tests are hown in table below. If the flexural strength of the concrete is 1505 KPa, determine the pad needed for failure in each test using four points loading. Show the detailed alculations and loading system sketches. S.N Width, mm Depth, mm Span, mm (Width +18 (Depth +0.5x18 (Span +18 149.2 148.4 471 143.3 146.8 466 3 137.6 137.1 450

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Plz, solve this problem in all its parts. Reinforced Concrete Design-1 Follow ACI Code (American Concrete Institute) Last two digits of Registraion Number: 95 A simply supported beam having span length of 24′ and cross-section of 15" × 21"is subjected to an ultimate load of ?? k/ft. Taking ?c = 3??? and ?y = 60???, a) Calculate the amount of reinforcement required for a given beam section to fail under balanced condition.b) Determine the magnitude of strain developed in the tension steel at the ultimate stage if the magnitude of ?? = (?/10) k/ft. Where ? = Last two digits of Registration Number
1. Which of the following is the compressive strength of concrete if β1=0.65. a) 60 MPa b) 21 MPa c) 21 MPa 2. The minimum depth of a cantilever beam having unsupported length of 3.5 m and reinforced with rebars of fy=276 MPa is a) 357.5 mm b) 450.5 mm c) 347.5 mm
Help me please. Thankyou
The T-section shown is subjected to a design ultimate moment of M = 180kN.m. Find the required area of reinforcement given a 10% redistribution of moments was applied in determining The Moment. please give explanations with the steps and diagrams
Hope your help concrete design (CE410) thanks
300 mm 2D16 mm 3D20 mm For the reinforced concrete beam shown, calculate the bending stresses (fc, fs,and fs') in the concrete and reinforcement for a service-load bending moment of 115 kN-m. Assume normal-weight concrete with fc'=28 MPC and Grade 60 reinforcement (fy=415 MPa). Assume a cracked section ww 009 d'= 50 mm d= 546 mm
A flexure strength tests were performed on a concrete beam having a cross section of 0.15x0.15m and a span of 0.45m. If the total load at failure was 37.5kN, calculate the ff:a. The flexure strength of the concrete if center-point was applied.b. The flexure strength of the concrete if third-point was applied.c. Which of the two flexural tests is recommended in determining the flexure strength of the concrete and why?
7) Using air entrained concrete is best for interior slabs? T or F 8) Structural steel strength under compression is equal to strength under tension? T or F 9) It is not necessary to place control joints in concrete? Tor F
The loadsshown on the beam with a cross section at midspan as shown, are service (unfactored)loads. The concrete used is a normal weight concrete with compressive strength of 4000 psi.The yield strength of the reinforcement is 60,000psi. For the midspan section shown, computeφMn and show that it exceeds Mu
A hollow concrete masonry unit has an actual dimension of 150mm x 200mm x 400mm(W x H x L). The unit was tested in a compression machine with the following result.Failure load = 1,200 kNNet volume = 4,400,000 mm3Determine: a) the gross area compressive strength.b) the net area compressive strength.
For pretensioned axially tensioned member, how to calculate the effective prestress established in the concrete? How to calculate the destressing load, cracking load and ultimate load, respectively, in the loading stage? Write the calculation equations.
In order to evaluate the suitability of nonpotable water available at the job site for mixing concrete, six standard mortar cubes were made using that water and six others using potable water. The cubes were tested for compressive strength after 7 days of curing and produced the loads to failure (in kN) shown in Table P6.21. a. Based on these results only, would you accept that water for mixing concrete according to ASTM C94? b. According to ASTM C94, are there other tests to be performed to evaluate the suitability of that water? Discuss briefly. TABLE P6.21 Cubes Made with Cubes Made with Potable Water Nonpotable Water 64.6 73.5 70.4 74.8 63.0 79.7 71.6 69.8 70.6 83.7 64.0 74.4