FLEXURAL ANALYSIS CONCRETE UNCRACKED Problem: Calculate the uniform load (in addition to the beam weight) which will cause the section to begin to crack if they are used for 28 ft simple span. f'. = 4000 psi , the modulus of rupture f, = 7.5,/f",, and reinforced concrete weight is 150 lb/ft³. 15" 18" 2 #8 3" 12".

FLEXURAL ANALYSIS CONCRETE UNCRACKED Problem: Calculate the uniform load (in addition to the beam weight) which will cause the section to begin to crack if they are used for 28 ft simple span. f'. = 4000 psi , the modulus of rupture f, = 7.5,/f",, and reinforced concrete weight is 150 lb/ft³. 15" 18" 2 #8 3" 12".

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

a-Design the concrete column to carry the applied load Concrete allowable strength: 35 MPa P= 900 kN Column dimension needs to be 300 mm X B Material reduction factor 0.75 - Load factor 1.5 B mm 300
Design Problem 1 & 2 Determine the cracking moment for the prestressed beam section shown if f'c = 35 MPa. Use a modular rupture of fr Assume normal weight concrete. = 0.621√ f'c C = 100 mm b₁ = 350 mm D = 125 mm d = 440 mm h = 500mm b₂ = 200 mm Figure 1.0 Cc 60 mm C-150 mm h, 250 mm b₁ = 250 mm b. =350 mm Figure 2.0 d 630 mm h = 700mm Ce 70 mm
A rectangular beam has the dimensions (see Figure) b = 12 in., h - 20 in, and d 17 in. and is reinforced with three No. 9 (No. 29) bars so that As - 3.00 in. The concrete compressive strength fe is 4000 psi, and the tensile strength In bending (modulus of rupture) is 475 psi. The yield point of the steel f, is 60,000 psi. Determine the concrete compression stress at the top fiber caused by a bending moment M- 10 ft-kips. 9- 6.78 in, I= 4067 in, Es= 29000000, E = 3600000 17 in. 20 in. 3 #9 bars (A, - 3.00 in.?) 3 in. -12 in- Select one: a. 390 psi b. 1390 psi c. 200 psi d. 250 psi
Considering the nominal shear stress on concrete is f = 0.83 MPa. Calculate the allowable max spacing for 2-legged 10 mm stirrups? Use simplified calculation for Vc. Beam dimensions are 397 x 754 mm. Effective cover of steel reinforcement = 70 mm fy = 275 MPa Spacing should be in multiples of 10 mm. NOTE: USE STORED VALUES IN YOUR CALCULATION
Q-A pre-tensioned concrete member of section 200 mm x 250 mm contains tendons of area 500 mm² at centre of gravity of the section. The prestress in the tendons is 1000 N/mm². Assuming modular ratio as 10, find the stress (N/mm2) in concrete.
ineed the answer ASAP.ty 3decimal final answer Do not round off in between solution
Calculate the uniform load w (in addition to the beam weight) that will cause the section shown to begin to crack if used as a 28-ft simply supported beam. Use normal weight concrete with L=4000 psi. f = 60,000 psi, E₁=29,000 ksi, and the reinforced concrete weight = 150 lb/ft³. 4 in. 28 ft 4 in. 22 in. 30 in. 2 in. 2 in. 3 #9 ● ||—12 in—-|
A simply supported beam 6.5m long, 350mmx500mm, prestressed with a straight tendon located 150mm below the neutral axis with effective prestressing force, Pe, of 300kN. Total load carried by the beam is 20kN/m. A. Determine the area of the concrete, mm2.B. Determine the section modulus of the concrete in x10^3 mm^3C. Determine the compressive stress caused by the tendon alone if Pe is at the centroid, MPa
Determine the values of the distance cfrom the extreme concrete corppression fibers to the neutral axis, andr, for the beam shown in the following Figure fy 60,000 psi and fc 3000 psi. 0.003 21 in d-c 389 bars 3.00 in) = (0.003) 12 in Select one: a. 6.90 in, 0.0061 b. 6.25 in, 0.0069 c. 7.50 in, 0.0085 d.5.93 in, 0.0076
pls help me.
Correct solution
I need the answer quickly