Item 5 Column AB is made from high strength pre-cast concrete and reinforced with four in. diameter A-36 steel rods. The allowable normal stress for the high strength concrete and the steel are (dallow) con = 2.6 ksi and (allow)st = 24 ksi, respectively. The modulus of elasticity for high strength concrete is 4.2 x 10³ ksi and for A-36 steel is 29 x 10³ ksi. (Figure 1) Figure 1 of 1 10 ft a a 19 in. H 9 in. Section a-a Part A Determine the magnitude of the maximum allowable floor loading P. Express your answer to three significant figures and include the appropriate units. μА Pmax = 158.91 Submit h kips My Answers Give Up Incorrect; Try Again; 2 attempts remaining ? Provide Feedback Continue

Item 5 Column AB is made from high strength pre-cast concrete and reinforced with four in. diameter A-36 steel rods. The allowable normal stress for the high strength concrete and the steel are (dallow) con = 2.6 ksi and (allow)st = 24 ksi, respectively. The modulus of elasticity for high strength concrete is 4.2 x 10³ ksi and for A-36 steel is 29 x 10³ ksi. (Figure 1) Figure 1 of 1 10 ft a a 19 in. H 9 in. Section a-a Part A Determine the magnitude of the maximum allowable floor loading P. Express your answer to three significant figures and include the appropriate units. μА Pmax = 158.91 Submit h kips My Answers Give Up Incorrect; Try Again; 2 attempts remaining ? Provide Feedback Continue

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Using a simply supported pre-stressed concrete beam, explain the following status using stress diagrams: Stress condition due to pre-stress alone. Change of stress conditions due to the increment of external load: Decompression moment (bottom fibre compression = 0); Cracking moment (tensile strength develops at the bottom and starts cracking at the bottom); and Balance state (whole section is at an equal amount of compression).
Referenced concrete Using inner, not outer, triangles On the below
reinforced concrete design
A rectangular reinforced concrete beam has a width of 350 mm and an effective depth of 650 mm. The beam is reinforced with 8-28 mm diameter tension bars. Concrete strength is f'c = 20.70 MPa and steel yield strength is fy = 275 MPa. 1. Which of the following most nearly gives the steel ratio? A. 3.73% B. 2.79% C. 2.17% D. 1.62% the rectangular
Situation no. 1: Calculate the bending stresses in the concrete and the reinforcing steel, using the transformed area method: fc= 3000 psi, normal- weight concrete, n= 9, M = 250 ft-k. %3D -bym 60 in. - 1. Bending stress of concrete. a 0.057psi My = 5 in. b. 57ksi 不 A,=6 hars C. 6840 ksi d= 28 in. 684psi e. 2. Bending stress of steel. a. 24 4ksi b. 2.03 ksi C. 24354.00ksi 2.71ksi b12 in. d. e.
Civil Engineering -Construction Material & Testing A block of concrete masonry unit is tested for compressive strength. The outside dimensions of the specimen are 200 mm X 400 mm X 100mm . The cross section contains three (3) hollow square, 75mm each side, with a wall thickness of 25mm. Is the CMU, considered solid or hollow. Discuss why.
A rectangular reinforced concrete beam has a width of 300mm and an effective depth of 400mm. Concrete strength is f'c = 28 mpa and steel yield strength is fy = 280 mpa. The modulus of elasticity of steel is 200,000 MPa Compute for the total compressive forceon concrete.
A beam having a width of 500 mm and a total depth of 800mm is reinforced with 6-32mm dia bars, Compressive strength of concrete is 28 MPa and yield strength of reinforcing bars is 420MP.. 640 mm 800 mm 6 #32 80 mm 80 mm Determine the following: 1. depth of the compression block 2. strain in the tension reinforcement 3. moment reduction factor 4. nominal moment capacity 5. ultimate moment capacity 6. actual steel ratio 7. minimum steel ratio 8. maximum steel ratio 9. Tension force 10. Compression force
A beam having a width of 500 mm and a total depth of 800mm is reinforced with 6-32mm dia bars. Compressive strength of concrete is 28 MPa and yield strength of reinforcing bars is 420MPA. 640 mm 800 mm 6 #32 C 80 mm 80 mm Determine the following: 1. depth of the compression block 2. strain in the tension reinforcement 3. moment reduction factor 4. nominal moment capacity 5. ultimate moment capacity 6. actual steel ratio 7. minimum steel ratio 8. maximum steel ratio 9. Tension force 10. Compression force
Item 5 Column AB is made from high strength pre-cast concrete and reinforced with four in diameter A-36 steel rods. The allowable normal stress for the high strength concrete and the steel are (allow) con = 2.6 ksi and (allow) st = 24 ksi, respectively. The modulus of elasticity for high strength concrete is 4.2 x 10³ ksi and for A-36 steel is 29 x 10³ ksi. (Figure 1) Figure 1 ▾of 1 10 ft a P B9 in. 9 in. Section a-a Part A Determine the magnitude of the maximum allowable floor loading P. Express your answer to three significant figures and include the appropriate units. μA Pmax= 158.91 kips Submit My Answers Give Up Incorrect; Try Again; 2 attempts remaining ? Provide Feedback Continue
A 6m-simply supported beam cross-section is show in the figure below is prestressed with 15 wires of 5mm diameter at the bottom and 3 wires at the top. Assuming prestress in steel is 840 MPa and the density of concrete is 24kN/cu.m. Calculate the stress at bottom extreme fiber at midspan. (MPa) 250 mm- 25 mm 350 mm 65 mm
Column AB is made from high strength pre-cast concrete and reinforced with four in. diameter A-36 steel rods. The allowable normal stress for the high strength concrete and the steel are (allow)con = 2.4 ksi and (allow)st = 24 ksi, respectively. The modulus of elasticity for high strength concrete is 4.2 × 10³ ksi and for A-36 steel is 29 x 10³ ksi. (Figure 1) Figure 10 ft 9 in. H 9 in. Section a-a Part A Determine the magnitude of the maximum allowable floor loading P. Express your answer to three significant figures and include the appropriate units. Pmax = Submit 04 μA Provide Feedback Value Request Answer Units ?