A circular column is made of concrete [E. = %D 4.2(103)ksi] while being reinforced with six steel rods [Est = 29 (103)ksi]. It is acted upon 4 in. 30 kip by an axial force of 30 kip as shown in the figure to the right. Each rod has a diameter of 0.85 in. 3 ft

A circular column is made of concrete [E. = %D 4.2(103)ksi] while being reinforced with six steel rods [Est = 29 (103)ksi]. It is acted upon 4 in. 30 kip by an axial force of 30 kip as shown in the figure to the right. Each rod has a diameter of 0.85 in. 3 ft

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A disk and two circular shafts are connected and supported between rigid walls, as shown in Fig. 4. Shaft AB is made of brass (G: 50 GPa) and has a diameter of 150 mm and a length of 400 mm. Shaft BC is made of hollow monel (G: 68 GPa) with an outside diameter of 100 mm, a thickness of 8 mm and a length of 650 mm. If a torque of 15 kN.m is applied to the disk, determine:? The maximum shearing stress in each of the shafts.? The angle of rotation of the disk with respect to its no-load position.? If the maximum stress and rotation in the brass shaft is limited to 100 MPa and 0.014 radian and in the Monel shaft is 150 MPa and 0.034 radian, check whether the shaft is safe or not. Find also the factor of safety if it is safe. 15 kNm Figure 4
The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; I = 1760 in.4]. For the loading shown, determine:(a) the beam deflection at point A.(b) the beam deflection at point B.Assume MA = 200 kip·ft, P = 30 kips, LAB = 3.3 ft, LBC = 5 ft.
Two solid circular cross-section bars, one titanium and the other steel, each in the form of a truncated cone, are joined as shown in the figure and attached to a rigid vertical wall at the left. The system is subjected to a concentric axial tensile force of 500KN at the right end, together with an axisymmetric ring- type load applied at the junction of the bars as shown and having a horizontal resultant of 1000KN. Determine the change of length of the system. For titanium, E = 110 GPa and for steel, E = 200 GPa. Ring load 25 mm 50 mm 35 mm 25r 500 kN Steel Titanium alloy 0.45 m 0.90 m
12 +bh,d+bh 12 + b₂h₂d² Question 1.8 A box beam shown in Figure Q1.8 is subject to a bending moment about the z axis. The normal stress with the maximum magnitude due to the bending moment occurs at A IC B 4 Figure Q1.8 O a. Point C O b. Point A Oc. Point B O d. Point D
A circular aluminum column 6 m long has a diameter of 200 mm. Determine the critical load if one end is recessed. E = 73 GPa. σY = 250 MPa.
ENGINEERING MECHANICS
The 54-mm-diameter solid shaft is made of 2014-T6 aluminum and is subjected to the distributed and concentrated torsional loadings shown where T = 1.75 kN.m. (Figure 1) Figure 04m 0.6 m, 2 kN-m/m 1 of 1> Determine the angle of twist at the free end A of the shaft. Express your answer in degrees to three significant figures. 6 = 17 ΑΣΦ ↓↑ Submit Provide Feedback Request Answer vec ?
A solid 1.4 in. diameter shaft is used to synchronize multiple mechanisms in a manufacturing plant. The torque delivered by the shaft is 3500 Ib-in. What horsepower must be delivered to the shaft to maintain a shaft speed of 610 rpmn? What is the maximum shear stress developed in the shaft? Answer: P = hp T= psi
Express and identify the resultant of the two forces and one couple shown acting on the shaft angled in the x-z plane. Assume F = 480 lb, M = 390 lb-ft, a = 8 in., b = 16 in., 0 = 28% 10 M k) lb-in. Answer: M = (i b F i+
The figure below has the following data: F1 = 1.88 kN, F2 = 0.92 kN, F3 = 0.54 kN, a = 1.87 meters, θ = 38°, β = 45°. Determine the reaction at B in kN. Support A is a roller and Support B is a hinge. Answer is 1.426. Please show your solution.
A horizontal beam of length 3.00 m and mass 2.00 kg has a mass of 1.10 kg and width 0.170 m sitting at the end of the beam (see the following figure). What is the torque of the system about the support at the wall? Wall support 3 m, 2 kg 0.17 m. 1.1 kg Submit Answer Tries 0/40 4
4. A nylon [E = 360 ksi; v= 0.4] rod (1) having a diameter of dl = 2.50 in. is placed inside a steel [E = 29,000 ksi] tube (2) as shown in Figure P3.7. The inside diameter of the steel tube is d2 = 2.52 in. An external load P is applied to the nylon rod, compressing it. At what value of P will the space between the nylon rod and the steel tube be closed? Nylon rod (1)- Steel tube (2)