A. Calculate the stress in the concrete at the top and bottom extreme fibers under a positive bending moment of 78 kip, in psi (neglect steel reinforcement) B. If f'c= 3200 psi and normal weight of concrete is used, does cracking occurs? What is the maximum uniformly distributed load the beam can carry if it is used as a simple beam with a 26 ft span without exceeding the modulus of rupture of the concrete, in lb/ft? 250 mm 80 mm 130 mm 80 mm 80 mm

A. Calculate the stress in the concrete at the top and bottom extreme fibers under a positive bending moment of 78 kip, in psi (neglect steel reinforcement) B. If f'c= 3200 psi and normal weight of concrete is used, does cracking occurs? What is the maximum uniformly distributed load the beam can carry if it is used as a simple beam with a 26 ft span without exceeding the modulus of rupture of the concrete, in lb/ft? 250 mm 80 mm 130 mm 80 mm 80 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

What is the shear force to be carried by the reinforcements of a beam subjected to axial tension if it has a width of 313 mm and an over-all depth of 477 mm? The specified compressive lightweight concrete is 22.2 MPa and the yield strength of stirrups is 333 MPa. The distance of tension reinforcements from the outer fiber of the beam is 59 mm. Round off your final answer in 3 decimal places. Loadings: VDL = 72 kN %3D VLL = 62 kN Axial Tension (DL) = 90 kN Axial Tension (LL) = 19 kN
21. The column of reinforced concrete is loaded with P = 8000 lbs. The modulus of elasticity (E) is 4.2E6 psi and the Poisson ratio is 0.15. 16in 16in What is the normal stress along section b-b? a. -15.625 psi b. -7.81 psi c. -2.60 psi d. -11.04 psi
Determine the tensile steel ratio of a singly reinforced concrete beam for the following conditions using concrete strength f’c = 21 MPa and steel yield strength fy = 420 MPa. if the tensile strain is set as 0.009 upon crushing of concrete at a strain of 0.003. = [rr] (5 decimal places)
Solution please.
ve st Semest desi Q4) Concrete is required for walls of a building that will be moderately exposed to Intrained freezing and thawing. The cross section of a wall is 300 x 1500 mm. The smallest spacing between reinforcing steel is 50 mm. The specified compressive strength of Compressive strengthe 3 concrete at 28 days is 21.5 MPa and a slump of 50 mm. Portland cement type I is used with specific gravity of 3.15, maximum size of aggregate 25 mm and fineness modulus of fine aggregate is 2.4, absorption capacity and moisture content of fine aggregate are of 0.8%, and 1.75% respectively. The dry-rodded unit weight of coarse aggregate is 1650 kg/m³, absorption capacity and moisture content of coarse aggregate are of 0.8%, and 1.75% respectively. Both aggregates have a bulk specific gravity (SSD) of (2.65. The aggregates conform to the ASTM C33-84 requirements for grading. Estimate the quantity of (cement, fine aggregate, coarse 94 8.75 aggregate and water) for 1m³ concrete. Tooox 2.65 alka…
1. Which of the following is the compressive strength of concrete if β1=0.65. a) 60 MPa b) 21 MPa c) 21 MPa 2. The minimum depth of a cantilever beam having unsupported length of 3.5 m and reinforced with rebars of fy=276 MPa is a) 357.5 mm b) 450.5 mm c) 347.5 mm
Assuming concrete is un-cracked. Determine the cracking moment of the section. E = 2*10°MPa E = 2*10*MPa f' = 20MPA 300 mm 500 mm 3#20 60 mm1
The permissible bending compressive strength for M 25 grade of concrete is 8.5 N/mm². Its short-term and long-term modular ratios are, nearly
The design engineer specifies a concrete strength of 37.92 MPa. Determine the required average compressive strength for: a. a new plant where s is unknown b. a plant where s = 3.45 MPa for 22 test results c. a plant with extensive history of producing concrete with s = 2.76 MPa d. a plant with extensive history of producing concrete with s = 4.14 Mpa
Using a simply supported pre-stressed concrete beam, explain the following status using stress diagrams: Stress condition due to pre-stress alone. Change of stress conditions due to the increment of external load: Decompression moment (bottom fibre compression = 0); Cracking moment (tensile strength develops at the bottom and starts cracking at the bottom); and Balance state (whole section is at an equal amount of compression).
A continuous beam 250 mm x 450 mm carries 6 numbers of 12 mm diameter longitudinal bars as shown. The factored shear force at the point of inflection is 200 kN. Check if the beam is safe in bond. Assume M15 mix with = 15 N/mm2 and mild steel with o %3D 250 N/mm2. A clear cover of 25 mm canbe assumed. The design bond stress for mild steel bars in M15 concrete is specified to be 1.0 N/mm2. Section of point of inflection 6 no's of 12 mm dia
Determine the cracking moment Mcr for the beam depicted in Fig. 6.85. Assume normal-weight concrete, and Grade 60 reinforcing bars. Calculate the bending stresses in the extreme fibers of the cross-section for a service-load bending moment of 90 ft kips.