A rigid bar, the deformation of which may be neglected, is suspended from three rods and loaded as shown in the figure. Rod 1 is of copper, with a cross-sectional area of 1cm2; rod 2 is of steel, with a cross sectional area of 1.5cm2; rod 3 is of aluminum, with a cross-sectional area of 2cm2. Determine the stress in the rods if P 6 tonnes. %3D 2m -2 1:5m 13 1m D5m75m

A rigid bar, the deformation of which may be neglected, is suspended from three rods and loaded as shown in the figure. Rod 1 is of copper, with a cross-sectional area of 1cm2; rod 2 is of steel, with a cross sectional area of 1.5cm2; rod 3 is of aluminum, with a cross-sectional area of 2cm2. Determine the stress in the rods if P 6 tonnes. %3D 2m -2 1:5m 13 1m D5m75m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A rod is composed of copper and steel section rigidly bolted in the wall as shown in the figure. If an axial load of F= 300 N and the cross sectional area of the rod is 200 mm² , determine the stress in the section of copper. ... Copper Steel 2F F 3m 2m (A) 4.5 MPa (B 0.75 MPa C) 3.0 MPa D) 1.5 MPa
A bar of square cross-section is subjected to point loads of P1, P2, P3, and P4 as shown here. Find the magnitude of the force P3 necessary for the equilibrium, if P1= 130 kN, P2 = 230 kN & P4 = 180 kN. Also, determine the stresses in each section & the net change in the length of steel bar, where the respective side of a square and lengths are d1=55mm, L1=31 cm, d2 = 40mm, L2=38 cm, d3=55 mm & L3 =30 cm. Take E = 185 GPa. The force P3 to make it to equilibrium in kN is The Stress in section 1 in N/mm2 is The Stress in section 2 in N/mm2 is The Stress in section 3 in N/mm2 is and The total change in length in x10-3 mm is
The bar in the figure with a diameter of 25 mm and a length of 1000 mm is made of Ti6Al4V alloy. A to this bar A force of 1000 N is applied with an arm of 800 mm length from the point. this force (a) the highest stress in the bar, (b) the type of stress, (c) the location of this stress (d) calculate how many degrees the rod rotates under the effect of this force. (Module of Elasticity of Ti6Al4V alloy 105 GPa and Poisson's ratio is 0.3).
1- Calculate the stresses in members CE, DE, and DF. The cross-sectional area of each member is 1200 mm?. Indicate tension (T) or compression (C). P = 5 kN Figure P-111 6 m 8 m 8 m 8 m 6 m Fig 1 Fig 2
Answer the ff correctly. The rectangular bar shown is connected to a support bracket with a 24 mm diameter pin. The width of the rectangular bar is 70 mm and its thickness is 15 mm. The bearing stress in the bar cannot exceed 120 MPa. Determine the maximum value of Pmax that can be supported based solely on consideration of the bearing stress in the bar. Note: This question is not asking about any stresses in the support bracket...just bearing stress in the rectangular bar.
Q3: A steel rod is rigidly attached between an aluminum rod and a bronze rod as shown. Axial loads are applied at the positions indicated. Find the maximum value of P that will not exceed a stress in steel of 140 MPa, in aluminum of 90 MPa, or in bronze of 100 MPa. BRONZE = 500 mm² 4P STEEL A = 400 mm² 2.5 m 2.0 m ALUMINUM A = 200 mm² P 1.5 m 2 2P
An axial pull is acting on a bar consisting of two different materials is shown in figure.If the Young’s Modulus of M.S steel and Copper is 2 x 105 N/mm2 and 121 GPa respectively. Determine (i) Stress induced in each section, and; (ii) Total extension of the bar
A rigid horizontal bar ABC is supported by three vertical rods as shown. The system is stress free before the load is applied. After the load P is applied, the temperature of all three rods is raised by 110°F. Determine the magnitude of the normal stress in rod (1). Answer in MPa rounded-off to 2 decimal places. Rod (1) : E = 105 GPa; a= 22.0 x 10-5/°C A=500 mm² Rod (2): E = 200 GPa; a = 11.7 x 10-6/°C A=250 mm² 2,100 mm 4,400 mm (1) (2) B (2) P= 45 KN 2,100 mm I
A rigid bar AB is hinged at A and supported by copper rod 2 m long and steel rod i m long as shown in fig. the bar carries a load of 20 KN at B. the cross section areas of steel and copper are 200 mm2 and 400 mm2 respectively find the stress in each ?rod if Es=210 GPa and Ec=83 GPa Copper rod- 2 m Steel rod. -1 m- 1 m 2m -1 m- B 20 KN
mm. NegiCOL UIC wOg VA vUampvuva 1.4-12 A rigid member DAC as shown in Fig. P1.4-12 carries the load P. Bar AB is an aluminum bar whose cross-sectional area is 0.5 in, and it is pinned at A and B by 0.5-in-diameter pins in a single-shear configuration. If the maximum allowable normal stress in AB is 7000 psi and the maximum allowable shear stress in the pins is 15,000 psi, find the maximum allowable load P. For aluminum E 10 x 10° psi. %3D 8 ft 7 ft P B Fig P1.4-12
pru 15 Oy enüz evaplanmadı Ot 00 üzerinden aretlenmiş Txy Soruyu aretle Tnt Ox On (a) (b) On the surface of a structural member, stresses are given as Ox=67,9 MPa, oy=25,5 MPa and Tyy=-24,3 as shown in figure (a). If a=48,3 degree for the rotated element as shown in figure-(b), Determine the shear stress Tnt (MPa). Note: If the stress has negative direction, use - sign. Yanıt:
Aluminum A = 400 mm Bronze A = 200 mm Problem 2: An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in Fig. Axial loads are applied at the positions indicated. Find the maximum value of P that will not exceed a stress in steel of 140 MPa, in aluminum of 90 MPa, or in bronze of 100 MPa. Steel A = 500 mm 2P 4P 2.5 m 2.0 m 1.5 m Show all