A rigid horizontal bar ABC is supported by three vertical rods as shown. The stress free before the load is applied. After the load P is applied, the temper three rods is raised by 110°F. Determine the magnitude of the normal stress Answer in MPa rounded-off to 2 decimal places. Dod (1) F 0 x 10-618 A 500 mm2

A rigid horizontal bar ABC is supported by three vertical rods as shown. The stress free before the load is applied. After the load P is applied, the temper three rods is raised by 110°F. Determine the magnitude of the normal stress Answer in MPa rounded-off to 2 decimal places. Dod (1) F 0 x 10-618 A 500 mm2

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the maximum normal stress developed in the bar when it is subjected to a tension of P = 4.3 kN given t=5 mm, a=5.5 mm, b=5 mm, F0.5 mm, and D=2.2 mm. [note: Drawing is not to scale] P O 275.20 MPa O 734.26 MPa O 172.00 MPa O 1915.45 MPa O 716.67 MPa O638.48 MPa O573.33 MPa O 677.58 MPa
The rectangular piece of wood, 84 mm by 180 mm, is used as a compression block. The grain of the wood makes a 21.2º angle with the horizontal, as shown in the figure. Determine the largest axial force P (in N) that can be applied safely if the allowable stresses on the plane of the grain is 16.4 MPa for compression. Round off the final answer to three decimal places.
Determine the equivalent stress state of an element oriented 30° clockwise with respect to the element illustrated in the figure below.
The bellcrank is in equilibrium a) determine the diameter of the bar DE if the normal stress is limited to 100MN/m2.b) Determine the diameter of the pin located at C if the shear stress is limited to 70 MN/m2.c) Determine the crushing force in the support plates in C with a thickness of 6mm.
(1) Given: B P=28 KN Square Bars b₁ = 57 mm (2) Q =9 kN b₂ C b₂ = 19mm (3) Q R = 38 kN ↑ D b3 = 38mm R WHAT IS THE AXAIL STRESS IN BAR 2? ANSWER IN MPa ROUNDED-OFF TO 2 DECIMAL PLACES. POSITIVE FOR TENSILE STRESS AND NEGATIVE FOR COMPRESSIVE STRESS.
use lamp=81kg, AB=5mm, BC=8mm
A steel bolt has a diameter of 8 mm. The bolt is encased by a bronze tube that has an outer diameter of 15 mm and inner diameter of 8 mm. A force is applied to the bolt. F d3 d1 F Values for the figure are given in the following table. Note the figure may not be to scale. Variable F₁ Value 25 kN Esteel 200 GPa Ebronze 105 GPa a. Determine the magnitude of the normal force in the steel bolt, Nsteel. b. Determine the magnitude of the normal force in the bronze tube, Nbronze. c. Determine the magnitude of the normal stress in the steel bolt, σ steel. d. Determine the magnitude of the normal stress in the bronze tube, Obronze. Round your final answers to 3 significant digits. N steel = KN Nbronze = KN σ steel = MPa Obronze = MPa
1.21 need assistance thank you
Q-1) For the given state of stress, (a) draw Mohr's circle for this state of stress and show all values on it (b) determine the principal planes and the principal stresses, (c) determine the normal and shearing stresses after the element shown has been rotated through 25° clockwise, (d) determine the normal and shearing stresses after the element shown has been rotated through 10° counterclockwise. (e) Show the Gmax, min. Op, Os, Tmaxs o' values on an appropriate plane stress sketch. NOTE: The problem will be solved by only MOHR CIRCLE Method and all stresses and angles will be computed and indicated on Mohr Circle. All steps of solution will be displayed. Analytical solution will not be graded. 90 MPa + 30 MPa 60 MPa
In this figure is a strut and a cable which was use to lift a body. If the strut and a cable has a stress equivalent to your 50 and 76 in kips respectively determine the maximum weight of the body. Neglect the weight of the wood and cable. Round off the answer in two decimal places.
Question 1 Aluminum rod E = 10400 ksi Allowable axial deformation= 0.3 in. Tension in the rod=2300 lb. allowable normal stress in the rod = 12.8 ksi, Determine the the corresponding maximum length L of the rod. Answer in inches rounded-off to 2 decimal places
USE the mohr's circle method to determine the stress components acting on the inclined plane AB USE THE MOHR'S CIRCLE METHODE NOT THE ONE IN THE QUESTION