A steel bolt has a diameter of 8 mm. The bolt is encased by a bronze tube that has an outer diameter of 15mm and inner diameter of 8 mm. A force is applied to the bolt.Fd3d1FValues for the figure are given in the following table. Note the figure may not be to scale.VariableF₁Value25 kNEsteel200 GPaEbronze105 GPaa. Determine the magnitude of the normal force in the steel bolt, Nsteel.b. Determine the magnitude of the normal force in the bronze tube, Nbronze.c. Determine the magnitude of the normal stress in the steel bolt, σ steel.d. Determine the magnitude of the normal stress in the bronze tube, Obronze.Round your final answers to 3 significant digits.N steel =KNNbronze=KNσ steel =MPaObronze=MPa

**Contact me if you have any questions. Most of them are just conversion of units.**Please leave a…

Answered: A steel bolt has a diameter of 8 mm.…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A pipe with an inside diameter of 42 mm is subjected to an axial load of 850 kN. If the maximum allowable tensile stress in the pipe is 2.50 kN/mm², calculate the minimum wall thickness required for the pipe. Give your answer in millimetres (mm) to 2 decimal places
phy
Use the method of SECTIONS to find the true magnitude and direction in bar HG of the truss shown below in Fig 3.5 -500lb -100lb A 45° -200lb H -100lb 2 B -200lb -200lb MAGNITUDE AND DIRECTION OF SUPPORTS -500lb H -100lb 45° 2¹ C2D 2¹ Fig 3.5. -200lb -100lb LI 2 B 2₁ 2₁ D 2₁ E
The two rods (A-B and B-C) shown in the left panel are connected by pins at A, B, and C. The cross sections of A-B and B-C are 10mm×13mm and 10mm×10mm, respectively. The bilinear stress-strain relation shown in the right panel is for the material used to make the two rods, where Ei is the slope of the stress-strain curve for stresses between 0 and 80 MPa and E2 is the slope for stresses larger than 80 MPa. Note that Hooke's law is only valid for stresses up to 80 MPa. A 1 1 B 0.900 m 3 P = 30 kN 2.44 m C σ MPa 80 E₂ = 40 GPa E₁ = 80 GPa E a) Given the conditions above, find the axial elongation for each rod when subjected to P=30KN. b) Find the final position of Point B due to the applied load P at that location. Hint: Assume point B moves by unknown amounts Ax and Ay from its initial position, and then use right triangles to write the known final lengths of the cables in terms of Ax and Ay. The equations can be simplified by assuming terms Ax² and Ay² are so small they can be…
3
▼ Part A In (Figure 1), F₁ = 24 lb. Determine the magnitude of the projection of the force F₁ along the line of action of F₂. Express your answer in pounds to three significant figures. IVE ΑΣΦ F1 on 2 = 60°- 30% vec F, 25 lb FAKKY 60 30° ? lb
Part A What is the minimum tension P of the cord? Express your answer in pounds to three significant figures. ANSWER: P = Part B lb What is the orientation ? Express your answer in degrees to three significant figures. ANSWER: 0 = -P 10 lb A 15 in. 45 15 in. D 30° 10 lb
A 4ft long rod with a 0.29 inch diameter is subjected to a 10,130lb tensile load. What is the tensile stress in ksi? Answer to two decimal places. Three plates are held together by 2, 21 mm diameter bolts. If a 41 kN load is applied to the plates in shear, what is the shear stress in the bolts in MPa?
The force F exerted by the hand on the handle in the figure is 22 N. Calculate the compression force on member BE.Type the units in the numeric entry using a space between the units and the number. The use of capital letters is required.
The force F exerted by the hand on the handle in the figure is 54 N. Calculate the compression force on member BE.Type the units in the numeric entry using a space between the units and the number. The use of capital letters is required.
Q1) 28 N.m torque is needed to turn the bolt around its axis as shown in the Figure (1) below. Find the force F and the forces between the wrench's smooth face jaws and the hexagonal bolt head's corners A and B. Suppose the wrench fits on the bolt simply such that connection is only formed at corners A and B. 150 mm 14 mm
A steel bolt has a diameter of 8 mm. The bolt is encased by a bronze tube that has an outer diameter of 15 mm and inner diameter of 8 mm. A force is applied to the bolt. F d3 d1 F Values for the figure are given in the following table. Note the figure may not be to scale. Variable Value F₁ 25 kN Esteel 200 GPa Ebronze 105 GPa a. Determine the magnitude of the normal force in the steel bolt, Nsteel. b. Determine the magnitude of the normal force in the bronze tube, Nbronze. c. Determine the magnitude of the normal stress in the steel bolt, σsteel. d. Determine the magnitude of the normal stress in the bronze tube, σbronze Round your final answers to 3 significant digits. Nsteel = KN Nbronze = KN σ steel = MPa MPa Obronze

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS