Q1) 28 N.m torque is needed to turn the bolt around its axis as shown in the Figure (1) below. Find the force F and the forces between the wrench's smooth face jaws and the hexagonal bolt head's corners A and B. Suppose the wrench fits on the bolt simply such that connection is only formed at corners A and B. 150 mm 14 mm

Q: QUESTION 2: For the nose landing gear of an aircraft shown in the figure, calculate the internal…

A:

Q: 4.Three members of a frame on a knot plate can be seen in the picture below. Determine the size and…

A:

Q: Find the two forces Fbc & Fac as :shown in the figure below

A:

Q: The figure below shows a stored shaft where bearing A is a cylindrical bearing and bearing O is a…

A:

Q: 5) In the figure shown below the person pulls the cable vertically downward to move box number 1,…

A:

Q: PROBLEM 2: For the nose landing gear of an aircraft shown in the figure, calculate the internal…

A: Draw the free-body diagram of the nose landing gear.

Q: Determine the force Vectors F = 90 N and F43 in the four bar mechanism shown in figure below. Draw…

A: Given: F = 90 N OQ = 80 cm OA = 50 cm AB = 70 cm QB = 60 cm QE = 34 cm For this mechanism to be…

Q: 4. Forces F1 =F= 20N and the third force F3 25N act on a cube with the side of a=2m. a. Find the…

A:

Q: Sketch a free-body diagram of each element in the figure. Compute the magnitude and direction of…

A: To find: The forces in each element. FBD: The free-body diagram is shown below.

Q: 5-Two ropes are tied with a load of mass 60 kg, as shown in the figure. Calculate the tension in AC…

A: W = 60 kgW = 60 * 9.81 = 588.6 NFind tension in AC and tension in BC

Q: L length of the adjustable wrench in the figure; Choose a number from 152 to 252 mm that does not…

A: Moment = Force X perpendicular distance from axis

Q: Determine the angle θ (degrees).

A:

Q: 1. You are tasked to design a shaft for power transmission through a belt and pully at its right…

A: Given:To find:

Q: The figure above is a pin-joint frame with horizontal member length 12m and vertical member length h…

A:

Q: In the figure below, all the bearings are movable bearings and the C bearing is in an inclined…

A:

Q: The two bearings (B1) and (B2) are used to support a shaft as shown in the figure Using the data…

A:

Q: Q5/A) From the figure below, determine the reaction force at pin C. A 000 -0.6 m 10 kN 0.6 m 0.8 m с…

A: From the figure below, Determine the reaction force at pin C.

Q: 1. Calculate the moment at point (A) of the forces shown in figure. T;=10 2.5 m1 T1-3N 2.5 m T=3 N…

A:

Q: The crane arm in the figure lifts the 95 kg mass at the end. When the angle BC piston makes with the…

A:

Q: For the bracket shown in the figure: > The moment of the force (1000N) about pin A is.... > The…

A:

Q: 2. The solid shaft ABCDE has a diameter of 30 mm and is simply supported at its ends. The pulleys at…

A: Given: The diameter of solid shaft, d = 30 mm = 0.03 m The diameter of pulley B and D, D = 200 mm =…

Q: 3 digits behind comma From the given figure, F = 100 N. • Draw the FBD 1000 mm • Draw the action…

A: given data: F=100N AB=125mm BC=1000mm force at B?? force at A?? RAV=vertical force at point…

Q: The figure below depicts the tire, axle, and gear of a large tractor. The entire structure is in…

A: Given: The force at G, F = 5000 lb The radius of gear at G. r = 3 in The normal force at wheel, W =…

Q: Using the 12.9 in long wrench from Part A, the bolt has now been unscrewed a length of 1.70 in.…

A: Given- d1= 12.9 in           d2= 1.70 inforce vector F= {37.3i+5.00j+8.00k} lbDetermine- the moment…

Q: 6 in 60° 20 in Statics Instructor A vertical force of P = 100 lb is required to remove the nail at C…

A:

Q: n the system shown in the figure, 2 sheets are connected to each other with the help of rivets with…

A:

Q: In the given figure below, a tube was supported at A and E with a ball and socket and a wire at D…

A: As per our guidelines we are supposed to solve only 3 subparts if multiple subparts are asked .…

Q: The cable carrying three 400-N loads has a sag at C of hC = 14 m. Calculate the following:…

A:

Q: In the following armor find the forces in the members CD, KD and JK of section 1-1 indicated in the…

A: A pin support will exert both horizontal and vertical components of reaction as the reaction forces.…

Q: Compute the forces in the two angled

A:

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.