Oy Ot Txy Tnt Ox On n (b) (a) On the surface of a structural member, stresses are given as ox=67,9 MPa, oy=25,5 MPa and Tyy=-24,3 as shown in figure (a). If a=48,3 degree for the rotated element as shown in figure-(b), Determine the shear stress Tnt (MPa). Note: If the stress has negative direction, use - sign.

Oy Ot Txy Tnt Ox On n (b) (a) On the surface of a structural member, stresses are given as ox=67,9 MPa, oy=25,5 MPa and Tyy=-24,3 as shown in figure (a). If a=48,3 degree for the rotated element as shown in figure-(b), Determine the shear stress Tnt (MPa). Note: If the stress has negative direction, use - sign.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q1/ (A) - The mechanism of femur bone is approximated as a circular tube (3 cm and 2 cm are the outer and inner diameter respectively) under loads as shown in figure Q1-A, determine the state of stresses at the points A and B. 40 cm 5 cm 380 N Figure Q1-A 300 N
Two forces, 100 kN and 200 kN, act on the rectangular column in the figure. Find the stresses at A and B points according to the given and show them on the stress element.
Don't use stress transformations formula. Use equation of force equilibrium please
2) Tensile strength P is applied to the rectangular cross-section, whose cross-section dimensions are given in figure A (- 5; 15). force and a pressure force of 2P acts from the point B(- 15; – 10). According to this; a) Find the load P that the section can carry b) Plot the stress distribution on the section for the load P you found c) Determine the core region of the section (6,em = 6 kN/cm² ; ơb,em = 12 kN/cm²) 40 cm B(- 15; - 10) X+ 60 cm Al- 5;15)
The stresses in a 2-D rectangular steel body (E = 200 GPa, v=0.32) are xx = -A(L - x)y, and oxy = A(h² - 4y²); other stress components are zero. Here, L represents length and h is height. What is the strain component y xy A - (h² - y²) 8E O A A 8G - (h²-x²) - (h²-x²) 8E А A= (h²-y:²) 8G ?
Find the stresses in each direction, also find the change in volume of the block of dimension 110 mm x 40 mm x 43 mm, subjected to 3 mutually perpendicular loads. The load along length, breadth and depth directions are 10 kN (tensile), 25 kN (compressive), 22 kN (compressive) respectively. Take E as 120 GPa, Poisson's ratio as 0.3 (figure - 0.5 mark, calculation - 1.5 marks, solution - 2 marks) (ENTER ONLY THE VALUES IN THE BOXES BY REFERRING THE UNIT GIVEN IN BRACKET & UPLOAD YOUR HAND WRITTEN ANSWERS IN THE LINK PROVIDED) The stress along length direction (Unit in MN/m2)= The compressive stress along width direction (Unit in MN/m2?)=, The compressive stress along depth direction (Unit in MN/m?)= The change in volume of the block is (unit in mm)
The solid shaft is fixed in the wall at A (Figure Q2). A force F is applied at B, determine a) the stress components at points D and E, b) the principal stress at each of these points. (Draw free body diagram to show all loading forces and moments) Take F = 12 N and 0 = 45°. 1,25 mm 6 mm. 8 mm. 3 mm B F Figure Q2
Problem 3. Strains are measured on the surface of a structural component as &A = = 1200 x 10-6. EB = 500 x 10-6, &c = 300 × 10-6. E = 200 GPa and v = 0.3. b) a) Find the principal stresses and show these on a sketch of a properly oriented element. Use Mohr's Circle to find the stresses at 0 = 30° counterclockwise from the x axis and show these on a sketch of a properly oriented element. y 60° C B A X
The stresses shown in the figure act at a point in a stressed body. Note that the given stress values are absolute values and stress sign should be determined based on the figure.(a = 75°, 0,= 90 MPa, ay= 75 MPa, T= 54 MPa] Oy ox. Determine the absolute value of the shear stress (Tnt) at this point on the inclined plane. Answer: MPa Determine the normal stress on the inclined plane (o). 159.2 MPa 105.9 MPa 207.6 MPa 126.8 MPa -90.9 MPa
Find the stresses in each direction, also find the change in volume of the block of dimension 125 mm x 55 mm x 25 mm, subjected to 3 mutually perpendicular loads. The load along length, breadth and depth directions are 18 kN (tensile), 15 kN (compressive), 13 kN (compressive) respectively. Take E as 170 GPa, Poisson's ratio as 0.3 The stress along length direction (Unit in MN/m2)=. The compressive stress along width direction (Unit in MN/m2)= The compressive stress along depth direction (Unit in MN/m2)= The change in volume of the block is (unit in mm3) =
14 Oy iz planmadı Ot üzerinden Txy tlenmiş pruyu tle Tnt Ox On (a) (b) On the surface of a structural member, stresses are given as ox=67,9 MPa, Oy=25,5 MPa and Txy=-24,3 as shown in figure (a). If a=48,3 degree for the rotated element as shown in figure-(b), Determine the normal stress o (MPa). Note: If the stress is compressive, use - sign Vanıt:
For the problem shown in the figure,- Find the axial displacement at the end B- Determine the variation of stress along the axis of the bar.GIVEN: E=50 N/mm2 , d1 = 4 cm, d2 = 6 cm, L = 80 cm, t = 6 mm, F = 1000N