A load P is supported by a structure consisting of rigid bar ABC, two identical solid bronze [E = 15,000 ksi] rods, and a solid steel [E = 30,000 ksi] rod. The bronze rods (1) each have a diameter of 0.75 in. and they are symmetrically positioned relative to the center rod (2) and the applied load P. Steel rod (2) has a diameter of 0.50 in. The normal stress in the bronze rods must be limited to 14 ksi, and the normal stress in the steel rod must be limited to 18 ksi. Determine: (a) the maximum downward load P that may be applied to the rigid bar. (b) the deflection of the rigid bar at the load determined in part (a). (1) A 90 in. (2) B (1) C 50 in.

A load P is supported by a structure consisting of rigid bar ABC, two identical solid bronze [E = 15,000 ksi] rods, and a solid steel [E = 30,000 ksi] rod. The bronze rods (1) each have a diameter of 0.75 in. and they are symmetrically positioned relative to the center rod (2) and the applied load P. Steel rod (2) has a diameter of 0.50 in. The normal stress in the bronze rods must be limited to 14 ksi, and the normal stress in the steel rod must be limited to 18 ksi. Determine: (a) the maximum downward load P that may be applied to the rigid bar. (b) the deflection of the rigid bar at the load determined in part (a). (1) A 90 in. (2) B (1) C 50 in.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

b) A composite bar is shown in figure Qlb. Determine. The thermal stresses in copper tube and steel bar i. ii. Reaction in the steel bar. Copper tube (a1, E1) Steel bar (a2, E2) L = 500mm Fig Qlb Given: di = 100mm, L = 500mm d2 = 200mm, AT = 100°C Соррer Steel E (GPa) 100 200 al°C 16х 10-6 12 x 10-6
A steel [E = 200 GPa] bar (1) supports beam AB. The cross-sectional area of the bar is 700 mm?. If the stress in the bar must not exceed 530 MPa and the maximum deformation in the bar must not exceed 11 mm, determine the maximum load P that may be supported by this structure. Use dimensions of a = 8 m, b = 4.8 m, and c = 10.4 m. C (1) B Answer: P = kN
Two solid bars support a load P as shown. Bar (1) has a cross-sectional area of A₁ = 4350 mm² and an allowable normal stress of 85 MPa. Bar (2) has a cross-sectional area of A₂ = 4550 mm² and an allowable normal stress of 80 MPa. Assume x₁ = 1.5 m, x₂ = 3.0 m, y₁ = 1.4 m, and y₂ = 2.5 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress. Y₁ A Answer: Pmax= (1) B P x₂ KN
help asap pls
3. A cylindrical rod is fixed between two walls. The rod is composed of two materials. Section AC is made of one material (GAC = 2G) while section CD is made of a different material (GcD = G). A torque, T, is applied at point B, as shown below. Jac = JcD = J = 2 in. GẠC = 2G = 20 x 10ʻ psi T= 300 kip in. GCD = G = 10 × 106 psi A D 2L Determine the reactions at the wall, Ta, and Tp. Specify the direction for each. (Note: this is an example of a no calculator problem.) Ans: TA = 250 kip in ( Tp=50 kip in ( T Fixed Fixed to wall to wall
Two solid bars support a load P as shown. Bar (1) has a cross-sectional area of A₁ = 3950 mm² and an allowable normal stress of 115 MPa. Bar (2) has a cross-sectional area of A2 = 4550 mm² and an allowable normal stress of 135 MPa. Assume x₁ = 2.4 m, x₂ = 3.0 m, y₁ = 0.9 m, and y2 = 3.7 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress. Y/₂ (1) Y₁ Answer: Pmax KN = B P
QUESTION 1 A punch shown in Figure 1 is used to make a hole in a metal plate with thickness h3. The punch assembly is made of a hollow circular shaft with a material having a yield stress of oy = 400 MPa and Young's modulus E = 96 GPa. Load P, is acting at the top F while load P2 is uniformly distributed around the cap plate at E. Given that P, = 200 kN, P2 = 100 kN, I, = 80 mm, /2 = 120 mm, h1 = 300 mm, h2 = 300 mm and h3 = 50 mm. a) Determine the minimum required dimensions d, and d2 to the nearest mm under the application of maximum allowable stress. Apply a factor of safety F.S. = 2 against yielding. Given that t, = 10 mm and t2 = 8 mm. b) Based on the values of d, and d2 in (a), evaluate the average compressive stress at section FE and EA as well as punching shear stress through a circular surface through AC dan BD. Assume that t, = 12 mm and t2 = 10 mm. c) Suggest one material that can be punched and explain why. Also, suggest the maximum thickness that can punched for a 6061-T6…
Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. P = 10 kN a. What is the stress (MPa) in the Bronze material? b. What is the stress in Aluminum in MPa? c. What is the stress in Steel in MPa?
Provide a complete, step by step solution:
A steel [E = 200 GPa] bar (1) supports beam AB. The cross-sectional area of the bar is 660 mm2. If the stress in the bar must not exceed 290 MPa and the maximum deformation in the bar must not exceed 10 mm, determine the maximum load P that may be supported by this structure. Use dimensions of a = 7 m, b = 4.2 m, and c = 9.1 m.
The blue bar is made from steel with the following mechanical properties: Young's Modulus, E = 17x10° psi; Poisson's Ratio v = 0.31. The bar has a circular cross-section with diameter d= 0.50 in. being the length of each side. 557 lb 557 Ib 60 in. - Determine the following under the action of the axial load (assume elastic behavior): a. The bar's axial deformation, ô, in in.: b. The average axial or longitudinal strain, ELong: c. The change in the bar's diameter, in in.:
A steel [E = 25500 ksi] pipe column (1) with a cross-sectional area of A1 = 5.60 in.2 is connected at flange 8 to an aluminum alloy [E = 17500 ksi] pipe (2) with a cross-sectional area of A2 = 4.40 in.2. The assembly is connected to rigid supports at A and C. For the loading shown, determine the normal force in the steel pipe (1). A (1) 120 in. B 30 kips 30 kips 144 in. C