(a) An axial load P is applied at a point D that is 6 mm from the geometric axis of the square aluminium bar BC as shown in Figure 3.1 Investigate: i. The load P for which the horizontal deflection of end C is 10 mm. ii. The corresponding maximum stress in the column. Use E = 70 GPa. 6 mm D 44 mm 44 mm 0.75 m

(a) An axial load P is applied at a point D that is 6 mm from the geometric axis of the square aluminium bar BC as shown in Figure 3.1 Investigate: i. The load P for which the horizontal deflection of end C is 10 mm. ii. The corresponding maximum stress in the column. Use E = 70 GPa. 6 mm D 44 mm 44 mm 0.75 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Problem 3: (M4) Your boss at a construction company asked you to verify the thickness of a 3 m long hollow-square steel column (E=200 GPA) that can withstand an axial compressive load of 50 MN, the outer dimension a is 400 mm. The column's cross section is shown in Figure.4. Assume the column is a fixed-free type. Figure.4: Cross-section of a hollow-square steel column
Determined the maximum normal stress experience by the entire axial member and determine the section, which maximum stress occurs(ie AB or BC or CD)
i need the answer quickly
Problem 3: (M4) Your boss at a construction company asked you to verify the thickness of a 3 m long hollow-square steel column (E=200 GPA) that can withstand an axial compressive load of 50 MN, the outer dimension a is 400 mm. The column's cross section is shown in Figure.4. Assume the column is a fixed-free type. b Figure.4: Cross-section of a hollow-square steel column
The figure below shows a section of a column subjected to load P, which is applied 50 mm from the midline of the section's web. The column is made from material, which has an allowable normal stress of 180 MPa (both in tension and compression). The area of the section is 10050 mm?; the principal moments of inertia Imar = 146.554x106 mm and Imin 20.076x10° mm*. !! Determine the maximum allowable load P. 15 mm 150 mm 15 mm 150 mm 50 mm 15 mm 100 mm 100 mm 1194.6 kN 363.6 kN 1809.0 kN O 516.4 kN O 189.5 kN
A rectangular steel plate with a thickness h of 5 mm is shown below. All four edges are fixed. An uniform pressure of 20 MPa is applied on the top face of the plate. (Use E=210GPa and v=0.3) 1200 mm Please determine: 1) the maximum stress in the plate; and 2) the maximum deflection in the plate. 600 mm
An aluminium hollow box column of square cross section is fixed at the base and free at the top. The width of each side is b=150 mm and the thickness t=10 mm. A compressive load P = 160 kN acts on the outer edge of the column at the midpoint of the side as denoted by P. What is the longest permissible length L of the column if the stress is not to exceed 100 MPa? (E = 70 GPa) b Section 4-A
The rigid bar ABC is supported by pin at A and aluminium wire BD, is horizontal before the Load P is applied. Find the vertical displacement of point C caused by the load P=35 KN. Where E = 70 GPa and the area of the wire is 200 mm?. D. 300 mm B 400 mm- 200 mm
A steel bar of cross section 500 mm2 is acted upon by the forces shown in Figure. Determine 50 kN 15 kN 10 kN 45kN the total elongation of the bar. For steel, 0.6 m 1.25 m consider E = 200 GPa.
A vertical load P is applied at the center B of the upper section of a homogeneous frustum of a circular cone of length L, minimum radius rB, and maximum radius rA, as shown in the figure below. It is made of a material with a modulus of elasticity E. Neglect the effect of its weight. Use the following values: rA = 2 in, rB = 0.5 in, L = 3 ft, E = 30 (103 ) ksi, and P = 1800 lbf. Discretize the original geometry into three equal-length finite elements and (a) Compute all the nodal displacements. (b) Compute all the element axial stresses. (c) Plot the displacement field from the finite element method solution. (d) Plot the axial stress field from the finite element method solution.
Aluminum tube AB is fixed on support A, and the load P=60 KN is applied on Steel rod BC that is welded to tube AB via plate B. The cross-section area of the tube is equal to 1100 mm2 and the diameter of the rod is equal to 15 mm. calculate the axial deformation of point C? (Esteel=200GPa and EAl=70GPa)
An aluminum right-circular cylinder surrounds a steel cylinder as shown in the figure. The axial compressive load of 200 kN is applied through the rigid cover plate shown. If the aluminum cylinder is originally 0.25 mm longer than the steel before any load is applied, find the normal stress in each when the temperature has dropped 20 K and the entire load is acting. For steel take E = 200 GPa, ? = 12 × 10–6 /°C, and for aluminum assume E = 70 GPa, ? = 25 × 10–6 /°C.