The pin-connectsed structure consists of a rigid bar ABCD and two bronze alloy [E = 100 GPa] bares, each with a cross-sectional area of 340 mm2. bar (1) has a length L1 = 810 mm and bar (2) has a lenght L2 = 1080 mm. Assume dimensions of a = 480mm, b = 38mm, and c = 600mm. If the allowable normal stress in bars (1) and (2) must be limmited to 165 MPa each, determine: a) the maximum load P that may be applied at D to the rigid bar.                                                                               b) The deflection at D for the load determined in part (a).

Q: 2. A load of 12 kN falls 5 mm onto the end of a vertical bar 250 mm heigh and 2500 mm² cross-…

A:

Q: A homogeneous 950 kg bar AB is supported at either end by a cable as shown in the figure below.…

A:

Q: A homogeneous bar AB is supported at either end by a cable as shown in the figure. Calculate the…

A: Let m be the mass of bar AB  Diameter of cables,  Db= 28 mm  Ds= 20 mm  σb= 90 MPa  σs= 120 MPa…

Q: Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown in the figure.…

A:

Q: la a- 10 cm 44-4 600 N 14 cm Vertical load is applied to point Bof a 10 mm radius cylindrical bar as…

A:

Q: ess of bar: 6 m mm mm adius, r= 4 mm

A:

Q: A solid copper bar of circular cross sectionhas length L =1.25 m and shear modulus of elasticityG =…

A: Shaft is designed on the basis of following two criteria:- Strength Criteria According to Strength…

Q: 3. A tensile force is applied to the I-shaped piece of wood in a testing machine, in the arrangement…

A:

Q: The rectangular bar shown is connected to a support bracket with a 27 mm diameter pin. The width of…

A:

Q: A diagonal aluminum alloy tension rod of diameter d and initial length / is used in a rectangular…

A: We have to determine  Deformation of aluminum rod

Q: B D LA Lc C A b P

A:

Q: The rectangular bar of linear elastic material (E = 200 GPa, v = 0.25) is loaded as shown in the…

A: As it  is not mentioned that which three parts of the question need to be solved, please find the…

Q: F1. The rigid bar ABC in the figure is supported by a clevis and pin at its right hand side and by…

A: Draw the free-body diagram of the beam.

Q: (5) A homogeneous 800-kg bar AB is supported at either end by a cable as shown in the figure.…

A:

Q: Two solid bars support a load P as shown. Bar (1) has a cross-sectional area of A₁ = 3100 mm² and an…

A: According to the  given dataThe area of bar 1 is .The allowable normal stress in bar 1 is .The area…

Q: For the figure shown, have the following information: Bar (1) made of bronze Bar (2) made of…

A:

Q: The rectangular bar is connected to the support bracket with a circular pin, as shown in the figure.…

A: Bar width, w= 2.25 in Bar thickness, t= 0.375 in Pin diameter, d= 0.775 in Applied load, P= 4800 lb…

Q: Two solid bars support a load P as shown. Bar (1) has a cross-sectional area of A₁ - 3800 mm² and an…

A:

Q: 1. A brass shell is fully bonded to a steel core; the cross-sectional dimensions of the shell and…

A:

Q: A horizontal load PP is applied to an assembly consisting of two inclined bars, as shown in the…

A:

Q: Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at…

A:

Q: Two solid bars support a load Pas shown. Bar (1) has a cross-sectional area of A 3650 mm2 and an…

A: Stress is a physical mass that expresses the inner forces of a continuous material exerted upon each…

Q: The rigid beam in (Figure 1) is supported by the three suspender bars. Bars AB and EF are made of…

A:

Q: Determine the maximum axial force P that can be applied to the bar in the figure below. The bar is…

A:

Q: Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded, as shown. The…

A:

Q: Solve the previous problem again for the case where the mass of the rear door is Mt = 27 kg and the…

A: Given data: Mass of crate, mC = 68 kg. Mass of rear door, mT = 27 kg. Crosssection area of cable, A…

Q: e Q2 shows few loadings applied on bar ABD. Suppose the diameter of the bar is 60mm, and knowing…

A: Diameter of bar=60mm P1=13kNm, P2= 5 kNm and P3 = 12 kNm. a State of stresses at point H-Normal…

Q: See the figure below. AD is a member with varying diameters. There are three axial loads applied at…

A: Given data: The magnitude of the force acting at the point B is; F1=10 lbs. The magnitude of the…

Q: Calculate the stress, in MPa, in the steel segment of the compound bar shown in the figure if the…

A: Both ends of the compound bar are fixed. For steel bar, E = 200 GPa = 200×1000 MPa = Modulus of…

Q: Bronze A = 300mm² E = 83 GPa 2.00 m %3D Steel A = 600mm? E = 200 GPa 1.00 m A 0.60m 1.00 m 1.00m

A:

Q: Two solid bars support a load Pas shown. Bar (1) has a cross-sectional area of A1 = 2350 mm2 and an…

A:

Q: Answer: Pmax= i kN

A:

Q: A bar ABC length L consists of two parts of equal lengths but different diameters.Segment AB has…

A: Given: P=110 kN shortening of the bar = 0.8 mm (a)Maximum allowable diameter (b) distance b from…

Q: Q4\ A filleted. plate of thickness t supports an axial load P (Figure below). Determine the diameter…

A:

Q: Two solid bars support a load P as shown. Bar (1) has a cross-sectional area of A₁ = 3950 mm² and an…

A:

Q: A steel column of hollow circular with length, L is shown in Figure 2. The column cross section has…

A:

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.