A load P is supported by a structure consisting of rigid bar ABC, two identical solid bronze [E = 14100 ksi] rods, and a solid steel [E= 28000 ksi] rod, as shown. The bronze rods (1) each have a diameter of 0.61 in. and they are symmetrically positioned relative to thecenter rod (2) and the applied load P. Steel rod (2) has a diameter of 0.47 in. Assume L₁-39 in and L2-72 in. If all bars are unstressedbefore the load P is applied, determine the normal stresses in bronze rods (1) and steel rod (2) after a load of P = 29 kips is applied.O(1)AAnswers:0₁ = i0₂ = iL2(2)BPksi.ksi.L

Answered: Image /qna-images/answer/04753851-be43-468a-91e5-691ecba62e30.jpg

Answered: etermine the normal stresses in bronze…

Engineering

Mechanical Engineering

etermine the normal stresses in bronze rods (1) and steel rod (2) after

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

answer is not correct, it should be 13.89 MPa
Problem 6-4 A compound cylinder is made by shrinkage an outer tube on to an inner tube, the final dimensions being, external di- ameter 25 cm, internal diameter 15 cm and diameter at the junction of tubes, 20 cm. If the common radial pressure between the two tubes due to shrinkage be 17 MPa, determine the circumferential stresses at inner and outer diameters of both cylinders and shown by means of a diagram how these stresses vary with the radius. 77.44 80 60 60.44 40 20 7.5 10 12.5 - 20 r, (cm) - 40 - 60 – 60.71 -77.71 Hoop stress, MPa
please solve all queston
PLEASE ANSWER NUMBER 1.MECH 222-MECHANICS OF DEFORMABLE BODIES: PLEASE GIVE DETAILED SOLUTIONS AND CORRECT ANSWERS. I WILL REPORT TO BARTLEBY THOSE TUTORS WHO WILL GIVE INCORRECT ANSWERS.
An aluminium processing hot extrusion steel cylinder has an internal diameter of 0.18 m and an outer diameter of 0.72 m. Determine the stresses across the cylinder for the following conditions. (a) During cold extrusion of aluminium at an internal pressure of 600 MPa. 1.
A steel bar is desired to be formed until it has a final length of 1.8m. What length sould the bar in m be before the forming stress is removed? The yield strength is 427 MPa, the tensile strength is 572 MPa, and the youngs modulus 210 GPa. Round of to tenths
1. (a) Explain briefly why a single-cylinder ('mono cylinder') may be replaced with a force-fitted compound cylinder ('duplex cylinder') with the same inner and outer diameters for a high internal pressure bearing application. (b) An alloy steel cylinder of bore radius (n) 40 mm and outer radius (R) 60 mm is subjected to an external pressure of 30 MNM2. (1) Determine the circumferential stresses generated at the bore and outer surface of the cylinder. (II) Sketch the form of distribution of radial and circumferential stresses across a radius. (c) The cylinder in (b) above is to be used as a hydraulic cylinder. For this application, it needs to be strengthened by shrink fitting onto it a sleeve of outer radius (ro) of 80 mm of the same steel as shown in Figure 1(c). The interference pressure generated due to this fit is 30 MNM2. Observe: This pressure is the same as the external pressure used in the calculations in part (b). (1) Determine the circumferential stress generated in the…
Example 4.5 (Stress on a shrunk fit cylinder): A shrunk fit thick cylinder made of steel having an inner radius 8cm, interface radius 10 cm and outer radius 12 cm is subjected to an external pressure of -0.09M Pa. Internal pres- sure is atmospheric. Given that the shrinkage is 0.02 cm. Determine the radial and tangential stress distribution across the the thickness of the cylin- der (2) before loading with pressure and (b) after loading with pressure. The equation for the contact pressure with usual notations is given as AE(c² – a²)(b² – c²) Pc = 2c°(b² – a²) Take E = 200 x 106 kPa.
i need the answer quickly
A 13-kN hydraulic press for removing and reinstalling bearings in small-to medium-sized electric motors is to consist of a commercially available cylinder mounted vertically in a C- frame, with dimensions as sketched in the Figure shown below. It is being proposed to use ASTM A-48 (Class 50) gray cast iron (brittle material with ultimate strength, s.,= 345 MPa) for the C-frame material. Calculate the location of neutral axis upto 2 digits after decimal point in mm? 18 mm 38 mm 13 kN 1 10 mm A* 25 mm YA -90 mm 10 mm