Estimate pouer for aunealed fow carbon steel strip 20mm wide and1omm thck, olled to a tuick ness of 6mm. the roll radius s 200mm e the noll rotate 200ge/min use coeicient 04iction aae the dee ueosk aeuter fae =0 lo car bon ste Such as A 020 has K=530M pa and

Q: Based on the system shown in Figure 1, develop the position equations from your fixed datum lines,…

A:

Q: A bcc (111) surface has the following (3x1) adsorbate structure: Select all of the following LEED…

A: Solution: Given Data:

Q: QI Define five of the following with sketch. 1-Taper turning 2- Light alloys 3- AA2024 4- Rolling 5-…

A: Taper turning is a turning technique in which the cutting tool travels at an angle to the…

Q: solve both

A: Power input, Gear speed of input shaft, Gear ratio, Power loss,

Q: What is the maximum magnitude of the bending moment caused by force G? If none, enter zero. Do not…

A: It is required to determine the magnitude of the maximum bending moment by the force G.

Q: 1. What is the type of robot?

A: ***As per our company policy we are supposed to do only 1 question if you need the rest please…

Q: (a) Determine the -position of the centroid of the figure shown on the next page. (and draw it on…

A:

Q: ove that the calculated values ne graphical method and the ematical analysis method the same, for…

A:

Q: Draw the box closing mechanism given in the figure in the given dimensions. Determine the velocities…

A:

Q: can you resolve and draw the fbd

A: Freebody diagram of the cut section:

Q: Determine Stres

A:

Q: LA 5 mm 28 mm ー-ギー - 49 mm 49 mm

A: For triangle, X1= 0 Y1= (1/3)×95= 31.67 mm  A1 = 1/2 × 98× 95 = 4655 mm2 For semi circle, X2 =0 Y2=…

Q: ldentify the valvetrain components in the drawings. Place the identifying letter next to the name of…

A: Valve train get together for a gas powered motor contains a typical transporter which upholds the…

Q: ) The disk is rotating about point O with an angular velocity x=7 rad/s in the given direction. Rod…

A: Given Data: The angular velocity of the disc is ωo=7 rad/s. The value of other variables are r=4 m,…

Q: D 3.2-5. Use the graphical method to demonstrate that the fol- lowing model has no feasible…

A:

Q: The equation of the unit circle is _______________.

A:

Q: A plane's propeller can be modeled as a thin, uniform rod that rotates about its frictionless center…

A: Given data  F = 591 N  L = 6.51  m  mass of propeller (m) = 10.1 kg    To determine  (a) direction…

Q: 28 cm a? 100 cm 30° V 15 cm

A:

Q: Tät-/e205+(17-78 2.

A: Given Data⇒a↦=202+17.782

Q: 200 mm В

A:

Q: 620 mm 125 350 mm

A: Consider the line diagram of the following figure as shown below – From the line diagram, it is…

Q: Add the length of all the horizontal pieces. They go left and right.

A:

Q: The assembly consists of a 3-kg vertical pulley A and a 14 horizontal pulley B. If a 2-kg block is…

A: Given data: m=3 kgM=14 kgr=30 mmR=100 mmh=0.1 m Need to determine the speed of pulley B.

Q: Fload/8 Fload/4 ffort = Fload/8

A: According to the details provided in the question, we need to calculate  we need to find all forces…

Q: Q1: Find the angle of the force? 250 Ib 110 Ib 25 140 Ibk 40° 90 Ib 170 Ib

A:

Q: ENTIRE ANSWER IS WRONG

A: Initial velocityFinal velocityInitial angleFinal angleWeight of the basketball

Q: Using the method of joints, determine the force in each member of the truss shown. State whether…

A:

Q: A piezometer and a pitot tube (close to each other, as described in the figure) are connected to the…

A:

Q: For figure (4): The ring is subjected to two forces (F, and F2). Suppose that the resultant force…

A: Given data:

Q: Given : Mass of Gears A and B = 2.4 kgs Mass of Gear C = 12 kgs Gears A and B's radius of gyration =…

A:

Q: Crossed center lines are used in the .. . view Longitudinal Horizontal Circular All

A: Solution:

Q: In this case, the applied force is always pulls upward, but the amount of force that can be applied…

A: According to the given data  We need to find The true statement

Buckling of columns

The column is described as a vertical member of the structure that carries an axial compressive load, and buckling is a lateral deformation of the column under the application of load.