LA 5 mm 28 mm ー-ギー - 49 mm 49 mm

Q: Determine Iy. 50 mm 50 mm 300 mm 50 mm y -200 mm an -X We Problem 4

A:

Q: Calculate y, the distance from the base to the position of the Neutral Axis of the T-section shown…

A:

Q: pered gibs are adjusted by screws spaced out along the length of the gib

A: The statement mentions "Tapered gibs are adjusted by screws spaced out along the length of the gib".

Q: Specify a cylindricity tolerance of .0004 for the largest cylindrical surface on the part in the…

A:

Q: Which percentile is typically for designing lower-limit dimensions? - 95th 5th 50th 99th

A:

Q: Using the diagram, determine the maximum diameter for DIA B.

A:

Q: Q3 Draw Front, Top and side view of the drawing shown below. All dimensions in mm and scale 2:1. 18…

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: 2.34 Determine the resultant of the three forces of Prob. 2.22. Answer

A: Given:The three forces are:F1=800 NF2=408 NF3=424 N

Q: Problem 6 You've been asked to design a stamping tool as shown. What are the internal forces at A…

A: FBD

Q: nd Steel, respectively. Given the modulus of elasticity of materials are Ealuminium = 69 G %3D…

A:

Q: Determine the maximum deflection of the 70-mm-diameter A-36 steel shaft.

A: To find: The maximum deflection of the 70 mm diameter steel shaft. Given: The diameter of a steel…

Q: If the main scale reading(mm) and vernier scale reading (division) are 16 and 9 respectively for a…

A: It is a precision instrument with a low least count, and is used to take sub-millimeter dimensions…

Q: A power transmission shaft is to carry a steady 30 horsepower while rotating at 1000 rpm. Specify a…

A:

Q: Draw chalk diagram of all sections

A: To draw section views

Q: 1. The built-up beam pictured on the right is subjected to an internal moment of M = 75 kNm. a) At…

A: *The internal moment acting on the structure is M=75 kNm. *The total length of the T section is…

Q: m. nd Find the components of the equivalent force. Express the re Express the z, y, and z components…

A: The position vectors are-

Q: The steel box wrench (E=29,000ksi, v=0.32) is loaded with a 40-lb horizontal force and a 25-lb…

A:

Q: Tapered gibs are adjusted by screws spaced out along the length of the gib. Select one: O True O…

A: Tapered gibs

Q: wy = 1/2 Wy= 98 V = TT R = 4500 by = 0.12346 wx= 102.66 Mechanical V = 2000 x 1000 360 SSS.S کککک…

A:

Q: A Sluice gate is a device that is fitted in a sluice or fluid canal to operate and control the fluid…

A: We need to calculate the hydrostatic force acting on the sluice gate

Q: Apply the necessary symbology to establish the required tolerance and datum features to control the…

A:

Q: ZPQ'R= = LPQ'R= = MI i O rad

A:

Q: Through load analysis, force and moment diagram are obtained, as shown below. Diagram below shows…

A: The force that occurs between mating gears is normal to the surfaces in contact. The axial force Fa,…

Q: Figure Q2 shows a shaft consists of Rods AB, BC and CD which made of Aluminium, Brass and Steel,…

A:

Q: The L2 steel bolt as shown in Figure 4 has a diameter of 5 mm, and the link AB which is made from…

A:

Q: The thin plate with four holes as shown in Figure 6 has a mass per unit area of 33 kg/m². The radius…

A:

Q: Draw the following graphic symbols (a) Total run-out (b) position tolerance (c) symmetry tolerance

A: Given: Draw the given graphic symbols.

Q: Determine the x, y, z components of reaction at the thrust bearing D 0 = 0°.

A:

Q: 1. If the block is loaded with P = 282 kN, calculate the required dimension "b" of the key.   Write…

A:

Q: A force F = 6980 N acts upon a piston head, as shown in the figure. The gudgeon pin G connects the…

A:

Q: The tool starts at point P1 (X-50.0,Y-15.0) and goes around the part counterclockwise. It then goes…

A: CODES USED IN THE PROGRAM G01 -LINEAR INTERPOLATION G03- CIRCULAR INTERPOLATION , COUNTER CLOCK WISE…

Q: The rectangular lamina with breadth = 60 mm, depth = 30 mm. The Ixx value is _____________ mm4…

A:

Q: Compute the deflection of C after the load removed.

A: Given Conditions :

Q: 0.250 DRILL THRU SIX HOLES EQUALLY SPACED 23° 30° CYLINDRICAL PLATE 1" STD 8 PIPE 3" XS BI PIPE 3"…

A: Section A-A represents the following thing.

Q: Draw the following spring with all mensions in sheet (write down all the equations you used in the

A:

Q: The radial distance measured from the pitch circle of a gear to the bottom of the gear tooth is…

A:

Q: Using unity conversion ratios, show that 1.00 lbm weighs 1.00 lbf on earth

A: Given Data: The given mass is M = 1 lbm. The expression for the weight (W) is, W=Mg Where g is the…

Q: 1. 1. Which part has the longest length? 2. 2. Which part has the smallest tolerance for the outside…

A: As this question contains multiple parts, solution is provided for first three parts as per policy.…

Q: hat is the increment of the 3 cylinders?

A: When we increase the number of cylinders in a vehicle, the power and performance of the engine both…

Q: Three blocks A, B, and C and a grooved block D have dimensions a, b, c, and d as follows: a =…

A:

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.