1. A load is suspended from a steel wire with a radius of 1 mm. The load extends the wire the same amount as heating by 20°C. Find the weight of the load. (Ysteet = 21.6 x 1010 N.m-2) (Answer: 149 N)

Q: Actually, (a) and (b) were incorrect I already submitted it with a and b then I got the result…

A: Concurrent force system is a system of forces in which line of action of all the forces passes…

Q: In the crank-slider shown, OA = 5 cm, AB = 15 cm and the offset e = 7 cm. Find the value of angle a…

A:

Q: How much force in lbs will it take to lift a 10 -lb weight with a wheel and axle, when the axle is…

A:

Q: A torque of 18 N m is applied to a rotating part. The part has a moment of inertia of 0.078 kgm2.…

A: Here we will use the the torque equation and the rotational motion equation.

Q: Our mechanical engineering student and your instructor are at it again, this time with the student…

A: Curve is given and we will revolve it around the y-axis to get the solid body.We will use the method…

Q: Tabulate the absolute coordinates. Write a program to drill the holes and mill the rectangular…

A: Given: To find: Write a program to drill holes and mill

Q: A cable hangs between two poles that are 70-ft apart. The two poles are both 40 foot high. Sag is…

A:

Q: Problem 6 You've been asked to design a stamping tool as shown. What are the internal forces at A…

A: FBD

Q: 4. Consider a situation similar to that in Experiment 2. Given the following distances traveled…

A: In the question, it is asked about average velocity. Average velocity can be calculated the total…

Q: The distributed load of w = (-2x² + 4x + 16) lb/ft acts on the beam as shown(Figure 1). Part A…

A:

Q: Assume F-9 kN. Using RECTANGULAR COMPONENTS, determine the direction of the resultant force,…

A: To find: The direction of the resultant measure counter clockwise from the positive x-axis. Given:…

Q: Solve for the mobility.

A:

Q: Please help. Written on paper not typed on computer or keyboard please. Need help on all questions.…

A:

Q: A chemistry graduate student is designing a pressure vessel for an experiment. The vessel will…

A:

Q: If the hydraulic cylinder at H draws rod BC in by a distance d = 4.545 in, how far does the slider…

A:

Q: Determine the mass of a steel ball whose diameter is 16mm.

A:

Q: Solve the following problem and show your complete solutions. 1. An alloy steel having a diameter of…

A: Stress is proportional to strain.Please go through hand written solution.

Q: In a hydraulic press machine the diameters of the effort and load pistons are respectively 25 cm and…

A:

Q: In the figure shown, I=160mm, b=50mm and wAB=1100rpm (clockwise) Solve for (a) the velocity(m/s) of…

A: Length of the connecting rod, l= 160 mm Radius of the crank, b= 50 mm Angular velocity of the crank,…

Q: opic: torsion in circular shafts The hollow shaft used in the system has the following conditions:…

A:

Q: A person is pulled to the right on a sled (total mass of 53.3 kg) across the surface of a frozen…

A:

Q: 4. Determine the length of stroke of a slider E when the crank AC rotates by 30 degrees in counter-…

A: Find the attachment for the solution.

Q: Through load analysis, force and moment diagram are obtained, as shown below. Diagram below shows…

A: The force that occurs between mating gears is normal to the surfaces in contact. The axial force Fa,…

Q: JC BRA JC Ma = 2.5kg BRD BAD Mb=7kg Given that: The line of force for BRD is 5cm. Distance JC to Ma…

A: Mass, Ma= 2.5 kg Distance between JC and Ma, a= 16 cm Mass,Mb= 7 kg Distance between JC and Mb, b=…

Q: The wind velocity on the upstream side of a wind turbine is 5.2 m/s. If the turbine extracts 31% of…

A:

Q: The result that I got after solving it was 463.0721, is that correct?

A: Given: d= 0.27in τ capacity=26.5 ksi = 26500 psi. Factor of safety =1.6 To find: The maximum T-force…

Q: The angle of twist for a circular shaft subjected to a twisting moment is given bythe equation 0 =…

A: Given Data: The given relationship is θ=TLGJ The angle of twist θ is a dimensionless quantity. Its…

Q: QUESTION 2 A shaft rotates at 300 rpm. 1), If it carries a spur gear that delivers 5 hp to a mating…

A: Given: N=300 rpm

Q: A2.1 Please help. Written on paper not typed on computer or keyboard please. Need help both…

A:

Q: Part A - Construction of Mohr's circle for the state of stress For the element shown, construct…

A: Given Data

Q: 1. A meter stick is found to balance at the 49.7-cm mark when placed on a fulcrum. When a 50.0-gram…

A: As meter stick is balanced when fulcrum is at 49.7 cm, this distance is the center of gravity (G) of…

Q: 1. A bolt is expected to break at 105 ft-lb of torque. A cheater bar is being used to tighten the…

A: Given: The breaking torque is 105 lb-ft. Linear density of the cheater bar is 6.6 lb/ft. The bar is…

Q: A Bys Find the reactions. Fill in the blank's. 8k a 4' 6' 6. FBD

A:

Q: Please help. Written on paper not typed on computer or keyboard please. Need help on all questions.…

A: Step 1:a. Equation for the differential area aligned horizontally The differential area element dA…

Q: To help workers in your project site move dozens of equipment weighing 70 kgs to a height of 2.2m,…

A:

Q: f e (D d b C a k j a=38.0 b=41.5 c=39.3 d=40.1 e=55.8 f=39.4 q=36.7

A: a = 38.0b = 41.5c = 39.3d = 40.1e = 55.8f = 39.4g = 36.7h = 65.7i = 49.0j = 50.0k = 61.9l = 7.8m =…

Q: A 1725 rpm electric motor is to be used to drive a "flat belt" conveyor in a manufacturing facility…

A: The speed of the conveyor belt is, The diameter of the roller is, The number of teeth on the drive…