1. A meter stick is found to balance at the 49.7-cm mark when placed on a fulcrum. When a 50.0-gram mass is attached at the 10.0-cm mark, the fulcrum must be moved to the 39.2-cm mark for balance. What is the mass of the meter stick?

Q: b. Number of Links: L= Number of joints: J₁= Number of half Joints: J₂= Mobility = c. Number of…

A: In these drawn mechanism, we need to find the number of lower pairs (binary joints) and higher…

Q: A set of sprockets is constructed, as shown in Figure 1, so that the second and third rotate on a…

A: Solution: Given Data: r1=1 cmr2=4 cmrc=1 cmr3=3 cmN1=y rpmN2=u rpmN3=x rpm   To Find: (a) N1N2(b)…

Q: Draw the cavalier oblique projection of the object. Use 45° for the third axis.

A: Refer the following Cavalier Oblique view of the given orthographic views.

Q: Our mechanical engineering student and your instructor are at it again, this time with the student…

A: Curve is given and we will revolve it around the y-axis to get the solid body.We will use the method…

Q: The velocity of the piston is 52.9901 3 ft/s.

A: use sine rule

Q: 2.3. Outrigger

A: Given Data: Diagram of an outrigger

Q: Q1: (Planar mechanism) For the planar mechanism of figure below link 4 serves as slider support…

A: Given data 1. length of link 2 = 3cm2. length of link 5  = 7cm3. length of link AB  = 6cm4. length…

Q: Calculate the Degree of Freedom of the shown mechanism. Show your solution.

A: GIVEN DATA - Double slider Mechanism We have to find Degree of freedom of mechanism Concept used -…

Q: An airplane flies at 28.9 m/s. The engine thrust exactly balances the drag force, which is 7.3 N.…

A:

Q: Unit: BTU HL = Heat loss (BTU)= Hv x hours If loss for one day, H = 24 hrs If we are talking about a…

A: Heat loss (HL) per day through a single building element =  AreaArea (A)Resistance (R)×∆T×24 hours…

Q: 1-71 Consider a U-tube whose arms are open sphere. Now water is poured into the U-tube fr and light…

A:

Q: Fine E For calculations on this page, keep 4 digits after the decimal point. A mass m = 2.5 kg is…

A: Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: Don't Use Chat GPT Will Upvote And Give Solution In 30 Minutes Please

A: Step 1:Given:The force acting perpendicular to the road and at the left end of the stick is F1​.The…

Q: Q3/ Find the angles and the distance for each plane, using by draw the following the table for each…

A:

Q: 5-9. The solid aluminum shaft has a diameter of 50 mm and an allowable shear stress of T the largest…

A: Given: The diameter of the shaft, d = 50 mm The allowable shear stress = 60 MPa

Q: Draw the free-body diagram for the boom. Connection at A is a pin. Draw the vectors starting at the…

A: To draw: Free body diagram of the boom. Given: The connection at A is pin. Sketch: The force In wire…

Q: The elevation and tilt angle of table AB are controlled by an operator's hand at point D. The table…

A: Freebody diagram of Table AB:Freebody diagram of the member DCB:

Q: 1-41. A roller and lever mechanism is in the position shown in Figure P1-41. Find the horizontal…

A: Find , Horizontal distance between A and B.

Q: The wind velocity on the upstream side of a wind turbine is 5.2 m/s. If the turbine extracts 31% of…

A:

Free Body Diagram

The system of forces acting on a body tends to either rotate it or make the body undergo motion. In general, when an external agent exerts a force on a body, the body undergoes translational motion and rotational motion. The body has six degrees of freedom under the influence of that force. Here, three degrees of freedom are from the translational motion while the other three are from the rotation motion. However, sometimes the bodies are not allowed to undergo any motion and are fixed, under such conditions the body is said to be constrained.