A 3.2 m square footing is proposed to be used to support a 373 mm x 605 mmRC column loaded with 637 kN dead load and 856 kN live load. The bottom ofthe footing is 1.7 m below the ground. Assume soil weighs 19 kN/m3 and theallowable soil bearing pressure is 343 kPa. The thickness of the footing is 464mm. fc = 21 MPa and fy = 420 MPa. It is to be reinforced with 20 mmdiameter. Use 24 kN/m³ as the unit weight of concrete.Note: For two-way shear, use an effective depth measured from the top of thefooting until the top of the bottom-most bar (d3)What is the ratio of the Demand Shear Force and the Capacity in Two WayShear? (Vu/phiVn)Answer in 4 decimal places (1.6125, 1.5140, 0.8461, etc.)You AnsweredCorrect Answer1.3809 margin of error +/- 1%

Given data:- Square footing size = 3.2m x 3.2m column size = 373mm x 605mm Dead Load = 637 kN Live…

A 3.2 m square footing is proposed to be used to support a 373 mm x 605 mm RC column loaded with 637 kN dead load and 856 kN live load. The bottom of the footing is 1.7 m below the ground. Assume soil weighs 19 kN/m³ and the allowable soil bearing pressure is 343 kPa. The thickness of the footing is 464 mm. f'. = 21 MPa and fy = 420 MPa. It is to be reinforced with 20 mm diameter. Use 24 kN/m3 as the unit weight of concrete. Note: For two-way shear, use an effective depth measured from the top of the footing until the top of the bottom-most bar (d3) What is the ratio of the Demand Shear Force and the Capacity in Two Way Shear? (Vu/phiVn) Answer in 4 decimal places (1.6125, 1.5140, 0.8461, etc.) You Answered Correct Answer 1.3809 margin of error +/- 1%

A 3.2 m square footing is proposed to be used to support a 373 mm x 605 mm RC column loaded with 637 kN dead load and 856 kN live load. The bottom of the footing is 1.7 m below the ground. Assume soil weighs 19 kN/m³ and the allowable soil bearing pressure is 343 kPa. The thickness of the footing is 464 mm. f'. = 21 MPa and fy = 420 MPa. It is to be reinforced with 20 mm diameter. Use 24 kN/m3 as the unit weight of concrete. Note: For two-way shear, use an effective depth measured from the top of the footing until the top of the bottom-most bar (d3) What is the ratio of the Demand Shear Force and the Capacity in Two Way Shear? (Vu/phiVn) Answer in 4 decimal places (1.6125, 1.5140, 0.8461, etc.) You Answered Correct Answer 1.3809 margin of error +/- 1%

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A continuous footing installed at a depth of 3 feet with base of 4 feet wide is constructed on cohesionless soil with a unit weight of 125 lb/ft³ and an angle of internal friction of 31°. The factor of safety requirement for the design is 2. The water table is sufficiently below the base of the foundation that won't interfere with the design. Determine: 1. Allowable bearing capacity (qa) 2. Allowable wall load in lb/ft. Plb B
1. A continuous footing is shown in the figure below. Using Terzaghi's ultimate b.c. equation and bearing capacity factors, determine the gross allowable load per unit area (qall) that the footing will carry. Given: y = 112 pcf, c' = 450 psf, ' = 22°, D = 4 ft, B = 3 ft, and F.S. = 3. gall Unit weight of soil y c' $' 2. Repeat problem #1 using the general bearing capacity equation. Use the appropriate assumptions
A strap footing consists of two footings connected by strap beam. Allowable soil pressure is 450 kPa. Footing thickness is 600mm and the bottom of the footing is 1.5m below the ground. Assume soil weight to be 19 Kn/m3 and concrete weight to be 24 Kn/m³. Use f'c = 20.7 Mpa and fy = 414 Mpa. Use 1.2DL + 1.6LL. gog = galow - footing weight – soil weight. DL = 275 kN LL = 400 kN DL = 600 kN LL = 500 kN 4.8 m 400 x 400 column 400 x 400 column 1.2 m 1.2 m a) Calculate the footing dimensions. (Size is in multiples of 100 mm) b) Draw the Shear and Moment Diagram on the Longitudinal Direction. Show the maximum shear and moment.
a square footing is designed to support a 300-mm x 400-mm concrete column that sustains an axial dead load of 160 kn and an axial live load of 250-kn. the base of the footing is 1.50 m below the final grade line, the soil weight is 16 kn/m, the gross allowable soil pressure, qa is 210 kpa, and a surcharge of 30 kpa. use fy=415 mpa, fc= 28 mpa and flexure bars are 16 mm in diameterdetermine the minimum size of the footing. assume initial thickness of slab equal to 400mma. 1.2 mb. 1.5 mc. 1.7 md. 1.9 m determine the maximum ultimate wide beam shear stress of the following if b = 2 m, t = 600 mmdetermine the maximum ultimate punching shear stress of the footing if b = 2 m, t = 600 mm
A building will have a factored column load of 300 kN. The column is to be supported on a square spread footing underlain by a soil with the follow properties: c' = 5 kPa, o' 35°, y = 18.5 kN/m³. The groundwater table is at a depth of 15 m and the footing will be located 0.5 m below the ground surface. Determine the required footing size if Þ = 0.5. Use Terzaghi's bearing capacity equation for a square footing. Solve for 'B', making sure to use the reduction factor Þ; trial and error is the easiest way to solve for 'B'. Recommend a "reasonable" dimension for construction/design purposes.
Design an isolated rectangular footing: P(dead load) = 225 kN P(live load) = 130 kN Qa = 180 kPa Df = 1.5 m Unit wt. of concrete = 23.5 kN/m^3 Unit wt. of soil =17.2 kN/m^3 Bar diameter = 20 mm f`c = 20.7 MPa fy = 248 MPa Width of footing, B is limited to 2m only Column = 40 cm x 40 cm Assume height of footing = 350 mm (check adequacy, if failed - increase the depth) Use min. cover = 75 mm Determine the following: (a) Effective Soil Bearing Pressure, Qe (b) Footing Dimension, L (c) Ultimate Soil Bearing Pressure, Qu (d) Check for Shear Criteria (Beam Shear) (e) Check for Shear Criteria (Punching Shear) (f) Required Steel Area (Long and Short Direction)
A 3-foot square footing has its bottom 2.36 feet below the ground surface. The groundwater table is located at a depth of 4 feet below the ground surface. Unit weight of soil is 117 lb/ft3, saturated unit weight is 123 lb/ft3, cohesion 98 lb/ft3. Use angle of internal friction =30°. Nc = 35.4, Nq = 29.5, Ny = 19). Compute the allowable load that the footing could carry. Use FS = 2.9
A 500 mm square concrete column carries a factored ultimate vertical column load of780 kN. The vertical service load is 650 kN. It is to be supported on a square footing withf′ c = 17 MPa and fy = 420 MPa. The soil has an allowable bearing pressure for bearing cap-acity of 650 kPa (based on LRFD methods) and an allowable bearing stress for settlement of 160 kPa. The groundwater table is at a great depth. Determine the required footing width, thick-ness, size of the flexural reinforcement, and show your design in a sketch.
A square footing has a dimension of 1.78 m x 1.78 m and has its bottom 1.54 m below the ground surface. Compute for the gross allowable load in kg that the footing has to carry if it has a factor of safety of 2.86. Ground water table is located 0.73 m from the bottom of the footing. Soil Properties: c = 1,803 kg/m? Specific gravity, Gs= 2.67 Void ratio, e =0.47 - 30 degrees HINT: Use Dry unit weight for soil above the groundwater table. Unit weight of water 9.81 kN/m
Subject: Principles of Foundation Design (Use NCSP) A rectangular footing is to be used to support a 300x400 (*400mm side is parallel to the long dimension of the footing) column loaded with 420 kN dead load and 540 kN live load. One side of the footing is 4.0m. Use effective soil pressure of 70 kPa. f'c=35 MPa and fy=420 MPa. Use minimum steel ratio for longitudinal bars as 0.0018. •Calculate the required thickness of the footing (mm) based on wide beam shear. db=16mm. Size of footing should be multiples of 10mm (Answer: 300) •Calculate the required thickness of the footing based on two-way shear. db=16mm (Answer: 430) • Calculate the required number of 16mm bars along long direction. . Use the governing thickness based on shear requirements. (Answer: 22)
UPVOTE will be given! STRENGTH OF MATERIALS A rectangular footing has a dimensions shown and is acted upon by a dead load of 1,929 kN and a live load of 1,515 kN. The column dimension is 317 x 667 mm where he shorter dimension is parallel to B The thickness of the footing is 566mm. f'c=28 MPa and fy=420 MPa for diameter 20mm bars. A=2.7m and B=4m Calculate the number of bars along the long direction?
A square footing shown has the following details: Unit weight of soil = 15.28 kN/m3 Saturated unit weight of soil = 19.92 kN/m3 cohesion = 21.44 kPa %3D friction angle = 24 degrees %3D B = 2 meter Df = 2.45 meter P = 861 kN e/B = 0.12 --> one way eccentricity Calculate for the net allowable bearing capacity using FOS = 2.8. Use Meyerhof General Bearing Capacity Formula. D, B B Water table