A continuous concrete footing (yc = 24 kN/m³) of breadth 2.0 m and thickness 0.5 m is to be founded in a clay soil (cu = 22 kPa; y = 19 kN/m³) at a depth of 1.0 m. The footing will carry an applied vertical load of magnitude 85 kN/m run. The load will act on the centre line of the footing. Apply a factor of safety of 1.35 to the permanent action (dead load) and a factor of safety of 1 to the soil material properties and bearing resistance. Verify the bearing resistance limit state under undrained conditions. Is the width

A continuous concrete footing (yc = 24 kN/m³) of breadth 2.0 m and thickness 0.5 m is to be founded in a clay soil (cu = 22 kPa; y = 19 kN/m³) at a depth of 1.0 m. The footing will carry an applied vertical load of magnitude 85 kN/m run. The load will act on the centre line of the footing. Apply a factor of safety of 1.35 to the permanent action (dead load) and a factor of safety of 1 to the soil material properties and bearing resistance. Verify the bearing resistance limit state under undrained conditions. Is the width

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Calculate the number of steel bars #6 in a square footing necessary to resist a factored moment of Mu = 60 T-m. The footing has the following characteristics. B = 2.6 m, Fy = 4200 kg/cm2, f'c = 250 kg/cm2, d = 42.5 cm. Assume that the footing is ductile and you can use the reduction factor of 0.9 O 12 O 14 O 21 O 17
A 6ft x 6ft foundation is subjected to an axial load Q = 225k and a moment M = 100k ft. The depth of footing is 5ft. The soil unit wt is 125pcf, phi = 32deg and c=1000psf Find: qmin qmax e B' L' qult using the general BC equation
Q.1. A rectangular footing 2.0 m by 3.0 m is built in a homogeneous bed of sand of having bulk unit weight 20 kN/m³ and saturated unit weight 21 kN/m³ with an angle of shearing resistance of ( 37 P. The depth of the base of footing is 1.8 m below the ground surface and water table is located at a deth of 1.0m below the base of the foundation. a) Justify the adequacy of the footing if the proposed design load on the foundation is 1500 kN. b) depth 1.0 m below the ground Level. Calculate the safe load can be carried by the footing if the water table is located at a Consider the factor of safety of 3. Use Terzaghi's Analysis.
A 3.19m x 5.35m footing has a 407 mm column at center with the loads P = 875 kN and My=120.4 kN-m Calculate the pressure at point 2 of the footing in kPa ANSWER IS 64.5392
A building will have a factored column load of 300 kN. The column is to be supported on a square spread footing underlain by a soil with the follow properties: c' = 5 kPa, o' 35°, y = 18.5 kN/m³. The groundwater table is at a depth of 15 m and the footing will be located 0.5 m below the ground surface. Determine the required footing size if Þ = 0.5. Use Terzaghi's bearing capacity equation for a square footing. Solve for 'B', making sure to use the reduction factor Þ; trial and error is the easiest way to solve for 'B'. Recommend a "reasonable" dimension for construction/design purposes.
Foundation example
Design an isolated rectangular footing: P(dead load) = 225 kN P(live load) = 130 kN Qa = 180 kPa Df = 1.5 m Unit wt. of concrete = 23.5 kN/m^3 Unit wt. of soil =17.2 kN/m^3 Bar diameter = 20 mm f`c = 20.7 MPa fy = 248 MPa Width of footing, B is limited to 2m only Column = 40 cm x 40 cm Assume height of footing = 350 mm (check adequacy, if failed - increase the depth) Use min. cover = 75 mm Determine the following: (a) Effective Soil Bearing Pressure, Qe (b) Footing Dimension, L (c) Ultimate Soil Bearing Pressure, Qu (d) Check for Shear Criteria (Beam Shear) (e) Check for Shear Criteria (Punching Shear) (f) Required Steel Area (Long and Short Direction)
Solve fast
A 6ft x 6ft foundation is subjected to an axial load Q = 225k and a moment M = 100k ft. The depth of footing is 5ft. The soil unit wt is 125pcf, phi = 32deg and c=1000psf Find: 9min qmax e L' qult using the general BC equation