3. A square footing that carries an axial load of 150000kg has its bottom resting on a ground water table at a depth of 2.5m from the ground surface. Take PDRY = 1860kg/m3 and PSAT = 1950kg/m3, c = 1600kg/m2, ø = 30degrees. Use the approximate formulas for the determination of the bearing capacity factors. a.Compute the required width of the footing using a factor of safety of 2. b.Compute the ultimate bearing capacity of the soil. c.Compute the net factor of safety. d.Compute the net soil pressure.

3. A square footing that carries an axial load of 150000kg has its bottom resting on a ground water table at a depth of 2.5m from the ground surface. Take PDRY = 1860kg/m3 and PSAT = 1950kg/m3, c = 1600kg/m2, ø = 30degrees. Use the approximate formulas for the determination of the bearing capacity factors. a.Compute the required width of the footing using a factor of safety of 2. b.Compute the ultimate bearing capacity of the soil. c.Compute the net factor of safety. d.Compute the net soil pressure.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A continuous footing installed at a depth of 3 feet with base of 4 feet wide is constructed on cohesionless soil with a unit weight of 125 lb/ft³ and an angle of internal friction of 31°. The factor of safety requirement for the design is 2. The water table is sufficiently below the base of the foundation that won't interfere with the design. Determine: 1. Allowable bearing capacity (qa) 2. Allowable wall load in lb/ft. Plb B
1. A continuous footing is shown in the figure below. Using Terzaghi's ultimate b.c. equation and bearing capacity factors, determine the gross allowable load per unit area (qall) that the footing will carry. Given: y = 112 pcf, c' = 450 psf, ' = 22°, D = 4 ft, B = 3 ft, and F.S. = 3. gall Unit weight of soil y c' $' 2. Repeat problem #1 using the general bearing capacity equation. Use the appropriate assumptions
A 1.70 m by 2.60 m footing has its base 1.70 m below the ground surface. GWT is a meter above its base. (L along x-axis) Y = 15.75 kN/m C= 15 kPa Yut = 19 kN/m =26° Using Meyerhof's formula, determine the net ultimate load that the footing could carry if e = 0.45 m and es = 0.30 m. PLEASE MAKE YOUR HANDWRITING READABLE AND CLEAR. THANK YOU SO MUCH :)
A continuous footing with a B = 7.5ft is constructed with a Df of 3ft in a soil with the following properties: c' = 210 lb/ft? Y = 115 lb/ft³ Ø' = 25° If bedrock exists 6ft below grade use equation 7.2 to determine the ultimate bearing capacity.
A 4.0 m square footing is proposed to be used to support a 766 mm x 766 mm RC column loaded with 550 kN dead load and 590 kN live load. The bottom of the footing is 2 m below the ground. Assume soil weighs 19 kN/m³ and the allowable soil bearing pressure is 307 kPa. The thickness of the footing is 563 mm. f'. = 21 MPa and fy = 420 MPa. It is to be reinforced with 20 mm diameter. Use 24 kN/m3 as the unit weight of concrete. Use an effective depth measured from the top of the footing until the center of the bottom-most bar (d1) Calculate the number of bars required in one direction. You Answered Correct Answer 13
For general c- soil, cohesion c is 50 kPa, the total unit weight y. is 20 kN/m3 and the bearing capacity factors are N= 8 and = 3 and N, = 2. Using Terzaghi's formula. Na Calculate the net ultimate bearing capacity for a strip footing of width B=2m at depth z = 1 m. Considering shear failure only, estimate the safe total load on a footing 10m long by 2m wide strip footing using a factor of safety of 3. %3D
A 3-foot square footing has its bottom 2.36 feet below the ground surface. The groundwater table is located at a depth of 4 feet below the ground surface. Unit weight of soil is 117 lb/ft3, saturated unit weight is 123 lb/ft3, cohesion 98 lb/ft3. Use angle of internal friction =30°. Nc = 35.4, Nq = 29.5, Ny = 19). Compute the allowable load that the footing could carry. Use FS = 2.9
A structural engineer finished a design of a library. They determine that each column will carry 1000 lbs. the soil beneath the footing has the properties: gamma= 130 pcf, c= 75psf, phi= 40 degrees. The groundwater table is of great depth so it’s no concern. Sketch figures. What is the minimum size of the footing for a factor of safety of 3? Case 1: assume square footing Case 2: assume round footing
A foundation is 3 mx 2 m in plan. Given: Df= 1.5 m, o'= 25°, c'= 70 kN/m². With General Bearing Capacity equation and FS = 3 assmuming general shear failure in soil, determine the net allowable load that the footing can carry. a) NOTE: Due to drought, groundwater level has been lowered down to a depth of 1.5m from the ground surface. b) Net allowable load that the footing can carry using general bearing capacity equation and F.S.=3 assuming general shear failure in soil. c) Ultimate bearing capacity (qu) using prakash and saran theory with eB=0.3m and eL=0.5m. y = 17 kN/m 1 m 1.5 m Groundwater level 3 m x 2 m Yut = 19.5 kN/m
Subject: Principles of Foundation Design (Use NCSP) A rectangular footing is to be used to support a 300x400 (*400mm side is parallel to the long dimension of the footing) column loaded with 420 kN dead load and 540 kN live load. One side of the footing is 4.0m. Use effective soil pressure of 70 kPa. f'c=35 MPa and fy=420 MPa. Use minimum steel ratio for longitudinal bars as 0.0018. •Calculate the required thickness of the footing (mm) based on wide beam shear. db=16mm. Size of footing should be multiples of 10mm (Answer: 300) •Calculate the required thickness of the footing based on two-way shear. db=16mm (Answer: 430) • Calculate the required number of 16mm bars along long direction. . Use the governing thickness based on shear requirements. (Answer: 22)
A square footing shown has the following details: Unit weight of soil = 15.28 kN/m3 Saturated unit weight of soil = 19.92 kN/m3 cohesion = 21.44 kPa %3D friction angle = 24 degrees %3D B = 2 meter Df = 2.45 meter P = 861 kN e/B = 0.12 --> one way eccentricity Calculate for the net allowable bearing capacity using FOS = 2.8. Use Meyerhof General Bearing Capacity Formula. D, B B Water table
A 3.3 m square footing is proposed to be used to support a 435 mm x 435 mm RC column loaded with 585 kN dead load and 643 kN live load. The bottom of the footing is 2 m below the ground. Assume soil weighs 19 kN/m3 and the allowable soil bearing pressure is 290 kPa. The thickness of the footing is 459 mm. f'. = 21 MPa and fy = 420 MPa. It is to be reinforced with 20 mm diameter. Use 24 kN/m3 as the unit weight of concrete. Use an effective depth measured from the top of the footing until the center of the bottom-most bar (d1) Calculate the number of bars required in one direction. Answer in multiples of 1