PLEASE ANSWER IT ALL ASAP FOR AN UPVOTE. THANKYOU. A 0.9 meter radius circular footing is embedded 1.07 meters beneath the ground surface. The groundwater table is located 1.51 meters from the ground surface. The soil report also indicates a homogeneous soil profile with cohesion = 19 kPa, moist unit weight = 17.63 kN/m3, and submerged unit weight = 10.83 What is the gross ultimate bearing capacity (kPa) of the footing?

PLEASE ANSWER IT ALL ASAP FOR AN UPVOTE. THANKYOU. A 0.9 meter radius circular footing is embedded 1.07 meters beneath the ground surface. The groundwater table is located 1.51 meters from the ground surface. The soil report also indicates a homogeneous soil profile with cohesion = 19 kPa, moist unit weight = 17.63 kN/m3, and submerged unit weight = 10.83 What is the gross ultimate bearing capacity (kPa) of the footing?

Principles of Foundation Engineering (MindTap Course List)

9th Edition

ISBN:9781337705028

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter10: Mat Foundations

Section: Chapter Questions

Problem 10.1P: Refer to the rectangular combined footing in Figure 10.1, with Q1 = 100 kip and Q2 = 150 kip. The...

See similar textbooks

Similar questions

A strip footing carries a load 14506 lbs per foot of length. The footing has a width of 2.3 ft. Determine the increase in vertical stress directly below the center of the footing at a depth of 0.8 ft. Provide your answer in psf, to 2 decimal place. Do not include units in your response.
Please help!!!
7. A continuous strip footing bears on sand with groundwater one-half the footing width below the base of the footing. Which of the following changes will Increase the allowable bearing pressure? D B/2 PFT B SAND A) Embedment depth remains D, but the footing width is decreased. B) Embedment depth remains D, but the groundwater is raised to B/4 below the base of the footing. C) Embedment depth and groundwater remain D and B/2, but the unit weight of the sand is increased. D) Groundwater remains at B/2 below the base of the footing, but the embedment depth is decreased.
Wall footings are 0.4m wide, 0.2m thk, 0.6m deep from NGL, with 2-inch thick gravel bedding. How much gravel is needed for gravel bedding of Wall Footings? Select the correct response: 1.2 cu.m. 0.6 cu.m. 0.4 cu.m. 1.0 cu.m.
Answer asap for upvote. A 1.4 m wide footing is embedded 2.35m beneath the ground surface. The investigation indicated a unit weight equal to 18.23 kN/m3. The cohesion is 15.7 kPa. The saturated unit weight of the soil is 19.10 kN/m3 Determine the net allowable load (kN) that can be carried by the footing if the groundwater table is 0.54m below the footing. Assume footing is a circle Terzaghi's Bearing Capacity A soil report for an undisclosed location summarizes the parameters for the ground strata below: Angle of internal friction, Φ = 34 degrees Factor of safety on bearing capacity = 3
A structural engineer finished a design of a library. They determine that each column will carry 1000 lbs. the soil beneath the footing has the properties: gamma= 130 pcf, c= 75psf, phi= 40 degrees. The groundwater table is of great depth so it’s no concern. Sketch figures. What is the minimum size of the footing for a factor of safety of 3? Case 1: assume square footing Case 2: assume round footing
Subject: Civil Engineering*** NSCP 2015
a square footing is to be constructed on a uniform thick deposit of clay with a unconfined compressive strength of 3kips/ft2. the footing will be located 5 ft below the ground surface and is designed to carry a total load of 300 kips. the unit weight of the supporting soil is 128lb/ft3. no groundwater was encountered during soil exploration. considering general shear, determine the square footing dimension, using a factor of safety of 3
Please help, I promise to give good feedback. Please do not just guess. Thank you!
Calculate the ultimate bearing capacity considering the following. A strip footing, 2 meters wide A square footing 3 m by 3 m A circular footing 3 m in diameter All footings are located at the ground surface and groundwater levels is at the ground surface. The soil is coarse-grained with saturated unit weight of 19.8kn/m3 and angle of internal friction 25°.
1. A 4ft by 4ft spread footing is proposed where the bottom of footing is set 2ft below grade. The column bearing on this footing will impose a load of 180kips. Assuming the subsurface conditions shown below with groundwater 5ft below grade, Use Schmertman's method to calculate the elastic settlement of the system 6 years after construction is completed, provide a clear sketch and show units and state assumptions. Oft Sand Ymoist = 120 pcf Phi = 30deg Es = 52 ksf 4ft Loose Sand 5ft Ymoist = 125 pcf Yat = 145 pcf Phi = 22deg Es (above GW) = 30 ksf Es (below GW) = 20 ksf 8ft Dense Sand Ysat = 155 pcf Phi = 35deg Es = 60 ksf 20ft 2. The foundation above is limited to a 1.5" settlement after 10 years, speak to whether the design is adequate and if not how can you adjust the project to meet this criteria.
1. Using the boring log shown below determine the ultimate bearing capacity of a rectangular footing having a width of 4 feet and a length of 8 feet. Standard Penetration Tests were conducted at 5 foot intervals. The depth of footing will be 3 feet below the ground surface. Project Name: Johnson Hall Location: Birmingham, Alabama Boring No.: B-2 Date: January 4, 2019 Surface Elev.: 357 ft Depth |(ft) Moisture N No. Description 4 inches of top soil (%) (tsf) Comments y = 120 pcf 5 Reddish Brown silty Clay 14 20 1.2 LL = 43 PI = 20 $ = 7° 10 Dark Reddish Brown silty Clay 15 22 1.3 15 15 21 1.6 GNE Boring Teminated at 15 feet N- Standard Penetration Test Number LL – Liquid Limit qu – Unconfined Compression Strength $ - Angle of Internal Friction Boring Checked after 24 hours PI – Plastic Index GNE – Groundwater Not Encountered