10. Calculate the ultimate bearing capacity considering the following: A. A strip footing, 2 meters wide. B. A square footing 3 m by 3 m C. A circular footing 3 m in diameter. All footings are located at the ground surface and groundwater level is at the ground surface. The soil is coarse-grained with saturated unit weight of 19.8 kN/m³and angle of internal friction of 25°.

10. Calculate the ultimate bearing capacity considering the following: A. A strip footing, 2 meters wide. B. A square footing 3 m by 3 m C. A circular footing 3 m in diameter. All footings are located at the ground surface and groundwater level is at the ground surface. The soil is coarse-grained with saturated unit weight of 19.8 kN/m³and angle of internal friction of 25°.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A building will have a factored column load of 300 kN. The column is to be supported on a square spread footing underlain by a soil with the follow properties: c' = 5 kPa, þ' = 35%, y = 18.5 kN/m³. The groundwater table is at a depth of 15 m and the footing will be located 0.5 m below the ground surface. Determine the required footing size if Þ = 0.5. Use Terzaghi's bearing capacity equation for a square footing. Solve for 'B', making sure to use the reduction factor ; trial and error is the easiest way to solve for 'B'. Recommend a "reasonable" dimension for construction/design purposes.
A 4.7 m square footing is proposed to be used to support a 398 mm x 398 mm RC column loaded with 860 kN dead load and 654 kN live load. The bottom of the footing is 2 m below the ground. Assume soil weighs 19 kN/m³ and the allowable soil bearing pressure is 285 kPa. The thickness of the footing is 552 mm. f = 21 MPa and fy = 420 MPa. It is to be reinforced with 20 mm diameter. Use 24 kN/m³ as the unit weight of concrete. Use an effective depth measured from the top of the footing until the center of the bottom-most bar Calculate the number of bars required in one direction. Provisions are given below for the minimum area of main reinforcements Reinforcement Type fy. MPa ima Nimist Deformed Bars < 420 MPa 0.0020A Deformed Bars and Welded Wire 2 420 MPa Reinforcement Greater of: 00018 x 420 0.0014A
Only correct answer is required..
A rectangular footing has dimensions shown and is acted upon by a dead load of 382 kN and a live load of 536 kN. The column dimension is 307x560 mm where the shorter dimension is parallel to B. The thickness of the footing is 656mm. fc=28 MPa and fy=420 MPa for diameter 20mm bars. A=2.6m and B=5.2m
Problem (2.8):The load-settlement data obtained from load test of a square plate of size (1ft) are as shown below. If a square footing of size (7t) settles (0.75 inch), what is the allowable soil pressure of the footing? Consider sandy soil. Load (Tsf) Settlement (inch) 10 0.4 14 0.6 16 0.8 19 1.0 0.1 0.2 0.3
A continuous footing with a B = 7.5ft is constructed with a Df of 3ft in a soil with the following properties: c' = 210 lb/ft? Y = 115 lb/ft³ Ø' = 25° If bedrock exists 6ft below grade use equation 7.2 to determine the ultimate bearing capacity.
Subject:( Geotechnical and foundation engineering )
Calculate the soil bearing capacity of a soil under a strip footing at a depth of 2.5 ft and 4 ft wide. Angle of friction: 30° Unit weight of soil: 133 lbs/ft3 Factor of safety: 3.0 Cohesion: 0
Two footings, one circular and the other strip, are founded on the surface of a purely Cohesionless soil. Diameter of the circular footing and width of strip footing is same. Then, the ratio of ultimate bearing capacity of circular to strip footing is:
Figure (a) shows the cross section of square footing of 3 m x 3 m. The soil properties are shown in the figure. i) ii) Determine the load Q that the footing can carry. Use the factor of safety (FOS) of 2.5. During rainy season, groundwater level increased to the soil surface. Based on this condition, calculate the new FOS and justify whether the existing footing is able to carry the same amount of load as calculated in (a) Not drawn to scale 1.6 m 0.4 m Water level 3m Q Soil properties Yd=18.3K³ Ysat = 21 kN/m³ = 30°
A building will have a factored column load of 300 kN. The column is to be supported on a square spread footing underlain by a soil with the follow properties: c' = 5 kPa, o' 35°, y = 18.5 kN/m³. The groundwater table is at a depth of 15 m and the footing will be located 0.5 m below the ground surface. Determine the required footing size if Þ = 0.5. Use Terzaghi's bearing capacity equation for a square footing. Solve for 'B', making sure to use the reduction factor Þ; trial and error is the easiest way to solve for 'B'. Recommend a "reasonable" dimension for construction/design purposes.
The underlying soil is a well-graded sand with c′ = 0, f′ = 36°, g = 126 lb/ft3, with a verydeep groundwater table. Using LRFD, design a rectangular footing to meet the ultimate limitstates using a resistance factor of 0.45. Assuming the average CPT tip resistance of the sand is300 kg/cm2, check to see if your design meets serviceability limits. Adjust the design as needed.