A footing carrying a load of 1500 kN. Depth of Footing is 3 m. maximum tolerable settlement is 45 mm Consider the following factor N=11 FOS = 2.5 Water table is very deep Use Teng's Equation Find the size of footing (Consider square footing)

Q: On the drawing (attached , apply a datum feature symbols to create a datum axis A-B by using the…

A: The given data is: For left side: Shaft Diameter Upper Limit=9 6.40 mmShaft Diameter Lower Limit=ϕ…

Q: Jse commands (rectangle, mirror) and List he commands to draw the following drawing start from a…

A:

Q: Determine external as well as total indeterminacy

A: Given data : Number of External support reaction (R)=2+2=4Number of member (m)=6Number  of joint…

Q: 1-2in. -1in-+1int Hin 3in- T 3in 2in

A:

Q: & Find the set of solutions xy dx + (y-3x²) dy = 0. %3D

A:

Q: Can you help me figure out the different symbols and how many of them are there and put them in…

A: Single Pole Switch Duplex Outlet Quadruplex Outlet Electrical Outlet Fan Outlet Wall Mounted…

Q: determine the distances x and y for equilibrium if f1=800 N and f2=1000N. (Hand written and clean…

A: Given data - F1 = 800 NF2 = 1000 N Find out - Distance x and y ?

Q: Explain the formula of fs

A: From the original solution: Given: Width, b = 18 in Effective depth, d = 26.5+2.5=29 in. Height of…

Q: A clockwise couple M = 4.5 N m is resisted by the shaft of the electric motor. (Figure 1) Part A…

A: Given: The moment M is 4.5 N.m. Consider the figure,

Q: For the given structures, determine the degree of indeterminacy. 6. T 6

A: The given beam has three support conditions. The Left end is a Fixed support.(3 reactions)…

Q: at state of given (All in The Stres point is MPa) 80 100 100 i) And Principal Stren & Principal…

A:

Q: 16. From a triangular steel plate XYZ, a triangular section VWZ was cleanly cut off. What should be…

A:

Q: 4- Which statement is true about the precedence of lines? A. a hidden line has precedence over a…

A:

Q: Determine the XT and YT(using both a and b) a. Using the Top Most, Left Most Reference Line b. Using…

A:

Q: Identify all ZERO force members

A:

Q: Find the Xp ¢ YT Зст I}1:25 cm Cocn 61.5 cm 0.75 cm

A:

Q: What is the Ix and Iy of the cross-section in mm4

A: Given: Required : Ix and Iy of the cross-section in mm4

Q: * Dount command Creates a filled circle or a filled ring O a filled circle or a wide ring. a wide…

A:

Q: Find the domains of: f(x)=- x - 9 a. {x\x€R, x#9} b. {x|x€R, x#-3, x#3} c. {x|x€R, x+-3, x # 3, x #…

A: Hello dear this is the solution of your problem The answer is found to be Option (b)  For…

Q: 1. Differentiate atmospheric pressure, gauge pressure and absolute pressure. 2. State the stability…

A: Note- Hi! Thank you for the question As per the honor code, We’ll answer the first question since…

Q: 80 mm -L- В D 60 mm

A:

Q: 643-218

A: Note: As you have nothing mentioned in this problem. So, we are assuming that we have to apply…

Q: PROBLEM 2: Determine Ix and Tx.

A: given- a plane figure to find- M.O.I  about X-axis and centroidal axis.

Q: show the (c)

A:

Q: ex (x+1)² +c

A: Write all numerators above the common denominatorUse  to expand the expression.

Q: 4x-2x2+1 find lim, 3x-5

A:

Q: х у The value of |2y + z y [2z + x [2x + y z is

A:

Q: What are the internal forces at point C of the beam

A: Find reactions:∑ MB=0RA12-500126-900+900=0RA=3000lbFind reactions:∑ Fy=0RA+RB-50012=0RB=3000lb

Q: 4) A precast T beam with the dimensions shown below is to be a used as a bridge over a small…

A: As per Bartleby's guidelines we are supposed to answer only first three questions. Kindly repost…

Q: How do I get the support forces

A: The x and y are the vertical and horizontal distances: x=12cos60=6 fty=6sin60=5.196 ft

Q: 3. Is Iust be par PROBLEM 1: The frame shown is supported with hinges at A and C and a pin at B.…

A: Both the hinges will have the two supports, they are :- RAx and RAy at A and RCx and RCy at C. Then…

Q: \frac{1}{4}+\frac{1}{8}

A: To find:- 14+18

Q: Figure 2. Inside perimeter Outside perimeter Centreline

A: Inside perimeter :Length×2+Breadth×2+2×2'+3'24'3''×2+12'×2+2×2'+3'=79'6''

Q: Draw and label theV and M 15KN diagrams. Fill in the blanks. Find M- max and the equations for q. V,…

A: The beam is an important element in the construction of any structure or building. It resists…

Q: 2.21 The rigid bars ABC and CD are supported by pins at A and D and by a steel rod at B. There is a…

A:

Q: If Ax B = = A.B then the angle between A and B will be %3D a) п b) π/2 ) π/3 TE e) None of the above…

A: To find angle between A and B

Load and resistance factor design

Load and resistance factors design (LRFD), also known as Limit state design (LSD), refers to the design method used in building engineering. A boundary condition is a condition of a structure where it can no longer meet the relevant design requirements. The condition may refer to the load level or other actions on the structure, while the terms refer to the integrity of the structure, suitability for use, durability, or other design requirements. A structure designed for LRFD is limited to keeping track of all possible actions during its design time and is always ready for use, with the appropriate level of reliability in each boundary condition. LRFD-based construction codes clearly define the appropriate levels of reliability in their instructions.