5-A 1.5x1.5 m square footing is constructed in a cohesive soil at depth 1.2 m the ultimate bearing capacity for this footing calculated using Terzaghi's equation was 728 kN/m2. If the load has an eccentricity of 0.18 m from the center line of footing what will be the value of ultimate bearing capacity using Meyerhof's reduction factor? a) 633 kN/m2 b) 673 kN/m2 c) 553 kN/m2 d) 728 kN/m2

5-A 1.5x1.5 m square footing is constructed in a cohesive soil at depth 1.2 m the ultimate bearing capacity for this footing calculated using Terzaghi's equation was 728 kN/m2. If the load has an eccentricity of 0.18 m from the center line of footing what will be the value of ultimate bearing capacity using Meyerhof's reduction factor? a) 633 kN/m2 b) 673 kN/m2 c) 553 kN/m2 d) 728 kN/m2

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

PROBLEM 1: Design a square footing that supports a 400 mm x 550 mm column. The column carries a service dead load of 980 KN and a service live load of 1110 kN. Use the following properties given: fc' = 30 MPa fy = 275 MPa depth of footing, 1.60 m Unit wt. of soil, 17 kN/m3 Allowable soil bearing capacity, 300 kPa Concrete clear cover, 70 mm Diameter of bar, 25 mm Unit wt. of concrete, 24 kN/m3
Question 8(a)
1. A continuous footing is shown in the figure below. Using Terzaghi's ultimate b.c. equation and bearing capacity factors, determine the gross allowable load per unit area (qall) that the footing will carry. Given: y = 112 pcf, c' = 450 psf, ' = 22°, D = 4 ft, B = 3 ft, and F.S. = 3. gall Unit weight of soil y c' $' 2. Repeat problem #1 using the general bearing capacity equation. Use the appropriate assumptions
The allowable settlement for the shown square footing is 2.5 cm. the footing is placed on clay soil with the following properties. Use 4 layers to calculate the consolidation settlement and see if it satisfies the criterion. (footing weight is negligible) Hint: use the following eqation for Aoz (Boussinesq equations) For square foundations: 0.5 Δσ. = P1=1000 KN 2.0 - 1 + 1.5 1 B (2) 1.76 (q - o:) YSat = 20 KN/m³ Y = 18 KN/m³ Cc = 0.1 eo = 0.6
Pls give me correct solution- In a plate load test on a soil, at a particular magnitude of the settlement, it was observed that the bearing pressure beneath the footing is 100 kN/m². The perimeter shear is 25 kN/m². Find the load capacity of a 2 m square footing at the same settlement.
Hello and hope your help with foundation CEE 430 thanks
do not answer unless you are a 1000% sure that you are correct
Problem #4 At a development site in Cebu, City, a plate-load test was conducted on soil whose properties resemble that of sand. The plate used in this PLT is 62 cm square. The ultimate load per unit are (qu) for the test was found to be 620 kN/m2. What should be the maximum allowable load of a 2.5 m square footing? Use a factor of safety of 3. Answer in N.
Question #3 A total load of 900 kN is uniformly distributed over a rectangular footing of size 3 x 2 m shown in in Fig. 2. Due to the load on this footing, using influence factors determine the vertical stress at a depth of 2.5 m a) Under the corner at point C b) Under the center D. c) If another footing of size 3 x 1 m with a total load of 450 kN is constructed adjoining the previous footing, what is the additional stress at point C at the same depth due to the construction of the second footing? d) Using Newmark's chart, determine the vertical stress due two both footings at a depth of 2.5 m under point E. C 2 m 3 m E 3 m 1 m
Solve fast