A plate load test was carried out on a ground having a uniform sand stratum upto sufficient depth. The size of the plate used was 40 cm x 40 cm. Load (kN) 10 20 30 40 50 Settlement (mm) 2 3.5 5.5 7.5 10.5 Calculate load that can be taken by a column footing of size 3.5 m x 3.5 m in this soil, for an allowable settlement of 1.95 cm

A plate load test was carried out on a ground having a uniform sand stratum upto sufficient depth. The size of the plate used was 40 cm x 40 cm. Load (kN) 10 20 30 40 50 Settlement (mm) 2 3.5 5.5 7.5 10.5 Calculate load that can be taken by a column footing of size 3.5 m x 3.5 m in this soil, for an allowable settlement of 1.95 cm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Changes at a manufacturing facility will result in replacement equipment being installed on an…

A: Given data:

Q: A 3m x 3m square footing is constructed at a depth of 2m in a 26m deep clay layer with following…

Q: Determine the consolidation settlement for the foundation shown in the figure below. The so profile…

Q: H.W.1 A plate load test was conducted in a sandy soil with a plate of size 0.3m * 0.3 m. The…

A: Size of plate = 0.3 m × 0.3mUltimate load = 2 kg/cm2Size of Footing = 2m ×2mFOS = 3Sandy soilto…

Q: Question Attached

A: Consider free body diagram;

Q: A rectangular footing 1 m x 2 m is placed at a depth of 2 m in a saturated clay behaving an…

A: Given- Rectangular footing size 1 m×2 m, Depth=2 m, UCS=100 kN/m2, It is needed to find the net…

Q: A 1.8 m square, 2 m deep footing supports a service load of 570 kN. It is supported on a clayeysand.…

A: Solution Given Data Service load= 570 kN 1.8 m square 2 m deep

Q: 1. Find the increase of pressure at point A due to loading q=400 kN/m² on the given rectangular…

A: Given data in question Intensity 400 kN/m2 Dimensions 8×4 m To find out Increase in pressure at A

Q: A strip footing 1.5 m wide is located at a depth of 0.75 m (equal to the foundation thickness) in a…

A: Width od strip footing = 1.5m , Depth = 0.75m = Thickness of foundation , Unit weight of sand =…

Q: Foundation Engineering Homework: The allowable settlement for a continuous footing shown in the…

A: Assume constant stress will go below the base of the foundation.

Q: A spread footing with a dimension of 2.0 m x 2.0 m is embedded in uniform clay at a depth of 1.0 m…

A: The given values are as follows,The spread footing size =2.0m×2.0mVertical downward load=300kNThe…

Q: Select the value of Cs to use for the edge of a 2'x20' flexible strip footing. Table 7-1 Values of…

A: cs values for different foudations are given as followscs value for flexible strip footing of…

Q: A pad footing of dimensions 1.2 m by 2.5 m applies a surface pressure of 425 kPa. The pad footing is…

A: Given: The dimension of the footing is 1.2 m x 2.5 m. The surface pressure is 425 kPa. The thickness…

Q: The figure below shows a proposed foundation site, with 10 ft of sand overlying 20 ft of clay with…

Q: 3. A 1882KN load is carried by a 2.6m x 2.6m square footing at a depth of 1.4m in a 30 m deep sand…

A: Step 1

Q: Question attached

A: Steps for determining the maximum load: 1) Long term (Drained stability) Shape factors are…

Q: 4. A 4m x 8m rectangular footing will be placed on ground surface as shown in the figure below. The…

Q: The allowable settlement for the shown square footing is 2.5 cm. the footing is placed on clay soil…

A: Data given Find : Consolidation settlement

Q: Determine the elastic settlement using the Schmertmann method of the 10'x 10' footing as shown…

A: A ) Given data : Footing size = 10'X10' Es = 10(N + 15 ) Where N is corrected SPT value. To Find :…

Concept explainers

Load and resistance factor design

Load and resistance factors design (LRFD), also known as Limit state design (LSD), refers to the design method used in building engineering. A boundary condition is a condition of a structure where it can no longer meet the relevant design requirements. The condition may refer to the load level or other actions on the structure, while the terms refer to the integrity of the structure, suitability for use, durability, or other design requirements. A structure designed for LRFD is limited to keeping track of all possible actions during its design time and is always ready for use, with the appropriate level of reliability in each boundary condition. LRFD-based construction codes clearly define the appropriate levels of reliability in their instructions.

Question

A plate load test was carried out on a ground having a uniform sand stratum upto
sufficient depth. The size of the plate used was 40 cm x 40 cm.
Load (kN) 10 20 30 40 50
Settlement (mm) 2 3.5 5.5 7.5 10.5
Calculate load that can be taken by a column footing of size 3.5 m x 3.5 m in this soil, for
an allowable settlement of 1.95 cm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data

VIEW

Step 2: Solution

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 6 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Example (11): (footing on clay) Determine the size of the square footing shown in figure below. If q,= 100 kPa and F.S.= 3.0? = 1000 kN G.S. Y soil 20 kN/m 2m Y conc. 24 kN/m² B = ? 0.4m
Q#4: Plate load test performed on a uniform deposit of sand and the following observations were recorded. The size of the plate was 45cm x 45cm. Plot the Pressure-Settlement Curve and determine the safe load on a footing 2m x 2m if the settlement is not to exceed 40mm. Pressure (kPa) 2 4 8 12 16 24 Settlement (mm) 3 6 20 40 60 100 Note: Write the proper answer in word format Subject: Geotechnical Design
A circular footing with a radius of r = 4.0 ft will be embedded D = 2 ft in uniform clay. The top of the foundation is at the surface. The water table is at the ground surface. An intact sample of the clay with Gs=2.75 was obtained using a thin-walled Shelby tube from a depth of 10 ft below the ground surface. The sample was saturated and has a gravimetric water content of 45 %. Estimate its void ratio e0 and total unit weight y _in pcf. Ovp' = 800psf Void Ratio 1.5 1.4 1.3 1.2 1.1 1.0 0.9 0.8 do 10 0.1 0 2 z/r, depth in radii 6 7 8 9 Cr = 0.07 100 1000 Effective Stress (psf) 0.2 0.3 0.4 0.6 0.81.0 7.0 10.0 Cc = 0.3 8.0 9.0 5.0 6.0 I, stress in percent of surface contact pressure 2 3456 8.10 10000 3.0 2.5 (2.0) 1.25 20 30 40 50 60 80 100 1.0 PAG 0.75 Note: Numbers on curves indicate offset distances in radii, x/r. 2r Z 0.5 0₂- KAB X 0.25 IX q 100 0, 10 FIGURE 4.10 Chart for calculating the increase in vertical stress beneath a uniformly loaded circular area. (From NAVFAC DM-7.1, 1982,…
Estimate the immediate settlement of a concrete footing 1.5m*1.5m in size founded ata depth of 1m in silty soil whose modulus of elasticity is 90kg/cm2 .The footing isexpected to transmit a unit pressure of 200kN/m2Assume, µ = 0.35, If = 0.82 for a rigid footing.
Need help solving this problem, thanks again