3 -The details for a tumed-bolted connection are given in the figure below The angle steelsection is subjected ro dcad and live loods. Caleulate the netr area requird for the checks onthe assembled parts. (F.=? cm)3 M16中M16-Soa)O 36,5b) 42C) O 17,5d) O 35Boş bırak

Answered: Image /qna-images/answer/65cd978c-eb18-46b7-ac2b-ffd7f728341c.jpg

3- The details for a turned-bolted conneetion are given in the figure below. The angle steel section is subjected to dead and live loads. Calculate the net arca required for the checks on the assembled parts. (F.= ? cm) -12 L100.100.10 50 3 M16 %24 M16 50 50 40 80 a) 36,5 b) 42 17.5 35 Boş bırak

3- The details for a turned-bolted conneetion are given in the figure below. The angle steel section is subjected to dead and live loads. Calculate the net arca required for the checks on the assembled parts. (F.= ? cm) -12 L100.100.10 50 3 M16 %24 M16 50 50 40 80 a) 36,5 b) 42 17.5 35 Boş bırak

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

View Policies Current Attempt in Progress the automobile bumper jack is designed to support a 4640-N downward load. Begin with a free-body diagram of BCD and determine the force supported by roller C. Note that roller B does not contact the vertical column. E 155 mm Answer: C- Save for Luster 155 mm 430 mm 2690 mm 4640 N D N $105 mm 250 mm Attempts: 0 of 1 used Submit Answe
Question #5. Calculate the allowable axial compressive load for a stainless-steel pipe column having an unbraced length of 20 feet. The ends are pin-connected. Use A-11.9 inch, r-3.67 inch and Fy- 40 ksi. Use the appropriate Modulus of Elasticity (E) per material used. All the calculations are needed in submittal. O 212 kip O 202 kip O 196 kip 224 Wip
3G KOREK docs.google.com/forms Q2: The extension spring shown in the figure has full-twisted loop ends. The material is AISI 1040Q&T 400F0 wire. The spring has 82 coils and is close-wound with a preload of 18 Ibf. (a) Find the closed length of the spring.(b) Find the torsional stress in the spring corresponding to the preload.(c) Estimate the spring rate. (d) What load would cause permanent deformation?(e) What is the spring deflection corresponding to the load found in part d? 0.162 in - in R 글-in R. Option 1
Answer the following for the section at Point D Only Calculate the distributed load "w" that: Will cause the section crack Will cause the reinforcement to yield. Material Properties: F'c = 5000 psi Fy = 60000 psi Es = 29000000 psi Ln = 27 ft L wl₂² 16 wl,² 14 CD L wl,2 vl₁² 10 11 win² 16 h: 28 in A=4 in² b=14 in n d: 25 in
HW A Solid Steel bar of dlameter 6omm andlengtj2. 350mmis p laced inside analuminum cylinderof Insie diameter Fommm and out side dlameter lomm, a compressive load of loo0 law is applled on the assembi n find the stresses in the barand the cylinder? take e Est= 200GPA and EAl= FoGla- SAL? D=u.25 %D লি Cover Plate 0.25mm di 350mm A lum. cylinder Steel bar
Situation 10: For the connection shown in the figure. Pu = 100 KN, x1 = 200, x2 = 200, y1= 50, y2 = y3 = y4 = 100 y1 y2 y3 y4 O 27 KN O 31 KN O 33 KN 0000 O 29.KN O O 1. Which of the following nearly gives the maximum force in the bolt due to the torque alone? x1 10000 x2
Given that the Gerber beam is drawn. Calculate and draw SFD,BMD,NFD Note : 1 ton = 1000kg Solve max in 25-30 mintes thank u
A 15" x 3/8" bar of A572 Gr. 50 steel is used as a tension member. It is connected to a gusset plate with 7/8-in diameter bolts as shown in the figure. Use s = 2.0 and g = 3.0. Determine the allowable tensile strength of the section based on tensile rupture of the net area. Answer: о о lo O o
A bolted connection between a vertical column and adiagonal brace is shown in the figure below. Theconnection consists of three 5/8-in. bolts that join two 1/4-in.end plates welded to the brace and a 5/8-in. gusset platewelded to the column. The compressive load P carried bythe brace equals 8.0k.Determine the following quantities: (a) The averageshear stress τavein the bolts, and (b) the average bearingstress σbbetween the gusset plate and the bolts. (Disregardfriction between the plates.)
An A36 steel plate with width of 400 mm and thickness of 12 mm is to beconnected to a plate of the same width and thickness by 34 mm diametersbolts, as shown in the figure (next slide). The holes are 2 mm larger thanthe bolt diameter. The yield strength of the steel plate is Fy = 248 MPa.Assume allowable tensile stress on net area is 0.60Fy. It is required todetermine the value of b such that the net width along bolts 1-2-3-4 isequal to the net width along bolts 1-2-4.a. Calculate the value of b in mm.b. Calculate the value of the net area for tension in plates in mm².c. Calculate the value of P so that the allowable tensile stress on net areawill not be exceeded.(Use at least 2 decimal points on your answers.)
AW10x30, 3.1 m long A36 steel is used as a column with fixed ends to support a service dead load of 267 kN. Calculate the maximum service live load the column can sustan uning LRFD Use theoretical value of k. Write your answer rounded to the nearest whole number in KN Use properties Ag = 5.703 mm2, rx = 111.25 mm, ry = 34.8 mm. Use stored value. Asnwer in 5 decimal places.
Problem No 2 A flanged-bolt coupling consisting of six 4 inch diameter steel bolts evenly spaced around a bolt circle 12 inches in diameter and four inch diameter aluminum bolts on a concentric circle 8 inches in diameter. What stresses are developed on each bolt of the two bolt-circles when a torque T=75 Kip-in is applied. Use Gs=12 x 10° psi and GA = 4 x10° psi.