1. Given the connection shown below carrying a load P = The connection consists of four pieces 20mm x 200mm x 700mm steel blocks fastened by four pieces 12mm diameter rivets. Solve for the following: a. Maximum shearing stress (2 decimals MPa) b. Maximum tensile stress (2 decimals in MPa) Maximum bearing stress decimals in MPa) C. Top View 700mm 100mm 100mm P 200mm Side View

1. Given the connection shown below carrying a load P = The connection consists of four pieces 20mm x 200mm x 700mm steel blocks fastened by four pieces 12mm diameter rivets. Solve for the following: a. Maximum shearing stress (2 decimals MPa) b. Maximum tensile stress (2 decimals in MPa) Maximum bearing stress decimals in MPa) C. Top View 700mm 100mm 100mm P 200mm Side View

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

SOLVE THIS PROBLEM USING THE SLOPE DEFLECTION EQUATIONS: The bearing type connection show is bolted by 4 – 22 mm diameter bolts (high strength bolts). The size of the plates is 300 mm x 12 mm. Fy 248 MPa, Fn = 330 MPa and Fu = 400 MPa. Determine the following: (1) Design strength of the connection based on strength of plates. (2) Design strength of the connection based on shear strength of bolts. =0.65. (3) Design strength of connection based on bearing strength of bolts on the 12 mm plate. =0.75 12 mm P. mm O. O 300 mm 40 80
2. For the figure shown below, determine the following; (60 points) a. Maximum tensile stress b. Maximum compressive stress c. Spacing/pitch of the bolts if the shear force resisted by each bolt is 30 kN 200 mm 100 mm 30 kN/m 10 mm 20 mm |100 kN 15 kN/m 5 kN-m 150 mm C D F 20 mm 3 m 0.5 m 0.5 m 1 m 3 m 20 mm 125 mm
1 please with explanation
From the bolted connection shown, the diameter of bolts is 20 mm with the hole diameter equal to 3mm larger than the bolt diameter, the angular section is 100x75x8mm, with an area of 1340 mm^2. Thickness of gusset plate is 9 mm. the gusset plate. (a)If T = 200KN, compute the shearing stress on the bolts. (b)If the allowable shearing stress on the bolt is 145MPa, compute the value of T.
Internal effortsfeatures on a 750 mm sheet wide (made of ASTM A36 steel) were determined using a software basic structure analysis. The effort characteristic requester from a usage overhead is equal to 1260kN. Calculate the thickness needed for the plate? Adopt fyk = 250 MPa and fuk = 450 MPa.Please help Expert sir
The plate shown is attached by using three M12x2 grade 8.8 bolts. Which screw is subjected to the largest stress? What safe load ( static) F can be supported by the screw for n=1.5.
Considering the following steel connection. The plates in Pink are 9mm steel plates. The middle plate (Yellow) is 18mm thick. The width of the plate is 100mm. The maximum allowable tension stresses on any of the plates is 100Mpa in Gross Area Yielding and 150 Mpa for Net Area or Tension Rupture. The bolts used are 8mm in diameter, the holes are 10mm in diameter, no need to add 1.6mm. The bolts allow a maximum of 280 Mpa of shear. Determine the maximum allowable "P" of the connection in kN.
Please show a detailed solution and explanation including its FBD. Thank you!
A 15" x 3/8" bar of A572 Gr. 50 steel is used as a tension member. It is connected to a gusset plate with 7/8-in diameter bolts as shown in the figure. Use s = 2.0 and g = 3.0. Determine the allowable tensile strength of the section based on tensile rupture of the net area. Answer: о о lo O o
Given: The L8x4x½ shown below is welded to the gusset plate by its long leg. L₁ = 10" and L₂ = 7.5". L₁ L₂ Determine the gross area. 5.80 in² Calculate the length of the connection. 8.75 Calculate the eccentricity of the connection. 0.854" Calculate the width of the connected element. Calculate the value of the shear lag factor. Calculate the effective net area. in² II
Q3-1 (Trusses), For the Figure shown below; 1 1. Find the forces in the members AB and AD of the truss and indicate whether it is in tension or 3m compression. 10KN 2. Read the following paragraph carefully then answer if it's TRUE or FALSE: The force in the member BC equal to zero? 3. Read the following paragraph carefully then CHOOSE THE CORRECT English Fried Safe 10KN 15 AN 3m 20 kN
P4.002 Three bolts are used in the connection shown in the figure. The thickness of plate (1) is 15 mm. The ultimate shear strength of the bolts is 350 MPa, and the ultimate bearing strength of plate (1) is 375 MPa. Determine the minimum bolt diameter required to support an applied load of P = 155 kN if a minimum factor of safety of 2.8 is required with respect to both bolt shear and plate bearing failure. Answer: dbolt min = (1) mm