Question #5. Calculate the allowable axial compressive load for a stainless-steel pipecolumn having an unbraced length of 20 feet. The ends are pin-connected. UseA-11.9 inch, r-3.67 inch and Fy- 40 ksi. Use the appropriate Modulus of Elasticity(E) per material used. All the calculations are needed in submittal.O 212 kipO 202 kipO 196 kip224 Wip

Answered: Image /qna-images/answer/d01066c5-43a0-4403-bb9b-fd48442c0c5a.jpg

Question #5. Calculate the allowable axial compressive load for a stainless-steel pipe column having an unbraced length of 20 feet. The ends are pin-connected. Use A-11.9 inch, rm3.67 inch and Fy-40 ksi. Use the appropriate Modulus of Elasticity (E) per material used. All the calculations are needed in submittal. 212 kip O 202 kip O 196 kip 224 Wip

Question #5. Calculate the allowable axial compressive load for a stainless-steel pipe column having an unbraced length of 20 feet. The ends are pin-connected. Use A-11.9 inch, rm3.67 inch and Fy-40 ksi. Use the appropriate Modulus of Elasticity (E) per material used. All the calculations are needed in submittal. 212 kip O 202 kip O 196 kip 224 Wip

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

need answer thank you
Consider a fillet sample subjected to a tensile force F while fixed to two 13-mm dia. bolts. Tensile failure will be observed at the portion where the stresses exceeded the elastic limit. Assuming uniform thickness, determine where the plastic behavior (behavior when the fibers exceeded the elastic limit) first occurred. a. Near one of the bolts b.40-mm section c.Near both bolts Tensile Force d.25-mm section Which of the following equations will give the maximum axial deformation for the member shown fixed at end A? PB Pc B A A PABLAB B. PABLAB AABEAB C. PARLAR D PcLac AnCEnC 40 mm- ←25 mm- PBCLBC + AABEAB ABC EBC PCLBC + AABEAB AncEnc 13 mm bolt C
Please show a detailed solution and explanation including its FBD. Thank you!
1 Situation 19. A composite beam shown is subjected to a bending moment of 500 kN-m. Determine the maximum flexural stress; 300 VIEW INNOVATIONS 200 200 100 55. Experienced by the steel 56. Experienced by the aluminum A. 0.03 B. 25.24 57. Experienced by the brass A. 25.24 B. 37.86 REVIEW I EW INNOVATIONS Steel, E=200 GPa Aluminum, E=70 GPa Brass, E-105 GPa wwwww C. 48.2 D. 72.11 C. 16.8 C. 16.8 D. 11.21 VIEW INNOVATIONS REVIEW INNOVATIONS REVIEW IS
Show full solution
Show complete solution. Thank you
Two plates are held together by 4, 10 mm diameter bolts. If a 26 kN load is applied to the plates in shear, what is the shear stress in the bolts in MPa? Type your answer...
Determine the available strength of the compression member shown in figure below.
For the given cross section below, Compute tne meximum stress of concrete and steel. All aimensions are in 'mm'. Use M-150KN-m ana n=8. Tne answers are | MPa ana MPa. 500 200 100 400 3-32mm Ø 100 100 10) 100
Problem 1. The composite beam shown below carries a cantilevered load of 10 kN. The beam consists of one 30 x 124 mm plate and four 12 x 50 mm plates. They are pinned together at 120 mm intervals with round pins. The pin material has a shear strength of 159 MPa. Compute the minimum acceptable diameter for the pins. O O O O O O O -0 O 0- O 1000 mm Do O -120 mm (typ) O O O P = 10 KN 30 x 124 mm 12 x 50 mm (typ)
The answer is close to 60 Ksi. I need help showing the work to get the answer . Please include units. Thanks
The composite A-36 steel bar shown is made from two segments, AB and BD, having cross-sectional areas of AB = 641 mm2 and BD = 1202 mm2 . Determine the vertical displacement (in mm) of end A. Modulus of Elasticity = 210 GPa. X = 1016 mm, Y = 790 mm, Z = 526 mm. Input the magnitude only. The answer is 0.58185. Show solution pls. Thank you.