KOBLE The lap joint in the figure is made using a 30 mm diameter bolt. The Duter plates are 5 mm thick, made of 2014- T6 aluminum and the inner plate is 10 mm thick and made of 6061-T6 aluminum. The bolt is made of $355 steel material. Calculate the load P that the lap joint can safely support, taking into account the failure of the plates by shear and tension and failure of the bolt by bearing and shear. Use a factor of safety for ultimate strength of F.S.=1.5 P/2 P/2 100 mm 20 mm

KOBLE The lap joint in the figure is made using a 30 mm diameter bolt. The Duter plates are 5 mm thick, made of 2014- T6 aluminum and the inner plate is 10 mm thick and made of 6061-T6 aluminum. The bolt is made of $355 steel material. Calculate the load P that the lap joint can safely support, taking into account the failure of the plates by shear and tension and failure of the bolt by bearing and shear. Use a factor of safety for ultimate strength of F.S.=1.5 P/2 P/2 100 mm 20 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

.
An A36 tension member shown in the figure is connected with three 19 mm diamter bolts. Diameter of hole = 22mm. Properties of 150 mm x 100 mm x 12.5 mm angle A = 3065 mm2 y = 50.55 mm Fy = 248 MPa Fu = 400 MPa Determine the desire strength due to fracture in the net section. Use U = 0.85 kN
Topic:Bolted Steel Connection - Civil Engineering *Use latest NSCP/NSCP 2015 formula to solve this problem The butt connection shows 8-22 mm dia. A325 bolts spaced as follows: S1 = 40 mm S3 = 50 mm t1 = 16 mm S2 = 80 mm S4 = 100 mm t2 = 12 mm Steel strength and stresses are: Fy = 248 MPa Fu = 400 MPa Allowable tensile stress on the gross area = 148 MPa Allowable tensile stress on the net area = 200 MPa Allowable shear stress on the net area = 120 MPa Allowable bolt shear stress, Fv = 120 MPa Bolt Hole diameter = 25 mm Questions: Calculate the allowable tensile load T, under the following conditions. a) Based on the gross area of the plate b) Based on the net area of the plate c) Based on block shear strength
3G KOREK docs.google.com/forms Q2: The extension spring shown in the figure has full-twisted loop ends. The material is AISI 1040Q&T 400F0 wire. The spring has 82 coils and is close-wound with a preload of 18 Ibf. (a) Find the closed length of the spring.(b) Find the torsional stress in the spring corresponding to the preload.(c) Estimate the spring rate. (d) What load would cause permanent deformation?(e) What is the spring deflection corresponding to the load found in part d? 0.162 in - in R 글-in R. Option 1
Question 9 Not yet answered Pants out of 100 The bolt in the figure below has a diameter of 0.75" inch. If the load P is 14,700 lbs, determine the average shearing stress in the bolt. 4E P fy= Select one: Oa 8.3k/in Ob. 83 k/in OC 601 k/in Od. 16.6k/in Oe. 33.2 k/in
SHOW COMPLETE SOLUTION AND DRAW ILLUSTRATION
A built-up section was made using PL414x12mm thk plates as shown in the figure below. It is pinned at both ends with additional support against weak axis at middle point. Assume A50 steel. PL414x12 DO Section W16x67 L x-axis a) Calculate moment of inertia at both axes in mm*. b) Determine the design compressive strength in kN if L-3m. c) Find the design compressive strength in kN if L=18m. Elevation y-axis
A 15" x 3/8" bar of A572 Gr. 50 steel is used as a tension member. It is connected to a gusset plate with 7/8-in diameter bolts as shown in the figure. Use s = 2.0 and g = 3.0. Determine the allowable tensile strength of the section based on tensile rupture of the net area. Answer: о о lo O o
1
Problem (4): A36 steel is used for the tension member shown in Figure below. a. Determine the nominal strength based on the gross area. b. Determine the nominal strength based on the net area. PL 300mmx17mm 150 75 75 75 75 75 125 ImmmmTmm"" mmn mm mm 50mm 100mm 100mm 50mm 19mm diameter bolts Problem (5): The tension m shown in Figur
Determine the load capacity of the angle LRFD. USE NSCP 2015.
P4.002 Three bolts are used in the connection shown in the figure. The thickness of plate (1) is 15 mm. The ultimate shear strength of the bolts is 350 MPa, and the ultimate bearing strength of plate (1) is 375 MPa. Determine the minimum bolt diameter required to support an applied load of P = 155 kN if a minimum factor of safety of 2.8 is required with respect to both bolt shear and plate bearing failure. Answer: dbolt min = (1) mm