Figure below shows an eccentric bolted connection. Four bolts of 16 mm diameter are provided to connect a 10 mm thick bracket plate to the flange of a column. The value of load P (in kN, correct upto two decimal place) such that resultant force on bolt A should not be more than 30 kN, is 250 mm ---- 90 mm 90 mm 75 mmi 75 mm

Figure below shows an eccentric bolted connection. Four bolts of 16 mm diameter are provided to connect a 10 mm thick bracket plate to the flange of a column. The value of load P (in kN, correct upto two decimal place) such that resultant force on bolt A should not be more than 30 kN, is 250 mm ---- 90 mm 90 mm 75 mmi 75 mm

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter8: Eccentric Connections

Section: Chapter Questions

Problem 8.2.10P

See similar textbooks

Similar questions

Give me right answer with clear calculations.
STAGGERED CONNECTIONS: A PLATE WITH WIDTH OF 400 mm AND THICKNESS OF 12 mm IS TO BE CONNECTED TO A PLATE OF THE SAME WIDTH AND THICKNESS BY 34 mm DIAMETER BOLTS, AS SHOWN IN THE FIGURE. THE HOLES ARE 2 mm LARGER THAN THE BOLT DIAMETER. THE PLATE IS A36 STEEL WITH YIELD STRENGTH Fy = 248 MPa. ASSUME ALLOWABLE TENSILE STRESS ON NET AREA IS 0.60Fy. IT IS REQUIRED TO DETERMINE THE VALUE OF b SUCH THAT THE NET WIDTH ALONG BOLTS 1-2-3-4 IS EQUAL TO THE NET WIDTH ALONG BOLTS 1-2-4. a. CALCULATE THE VALUE OF b IN MILLIMETERS. b. CALCULATE THE VALUE OF THE NET AREA FOR TENSION IN PLATES IN SQUARE MILLIMETERS. c. CALCULATE THE VALUE OF P SO THAT THE ALLOWABLE TENSILE STRESS ON NET AREA WILL NOT BE EXCEEDED.
Need right complete solution
Bolted and Riveted Connections From the bolted connection shown, the diameter of bolts is 18mm0 with the hole diameter equal to 3mm bigger than the bolt, the angular section is 100 x 75 x 8 mm, with an area of 1340 mm2. Thickness of the gusset plate is 9mm. The gusset plate and angle arc A36 steel with Fy = 250 MPa and Fu = 400 MPa. Determine the tensile capacity of the connection based on gross area. Determine the tensile capacity of the connection based on effective net area using a reduction factor of 0.85. Determine the tensile capacity of the connection based on gross area.
A 15" x 3/8" bar of A572 Gr. 50 steel is used as a tension member. It is connected to a gusset plate with 7/8-in diameter bolts as shown in the figure. Use s = 2.0 and g = 3.0. Determine the allowable tensile strength of the section based on tensile rupture of the net area. Answer: о о lo O o
Situation 8: For the connection shown in the figure. Pu = 80 KN, x1 = 200, x2 = 100, y1 = 50, y2 = y3 = y4 = 100 y1 y2 y3 y4 O 80 MPa O 71 MPa O 74 MPa oooo O 86 MPa O 1. Which of the following nearly gives the shearing stress of the most stress bolt? Use 20 mm diameter bolt. x1 O O O x2
The connection shown is subjected to a tensile force of P = 100 kN. The allowable shear stress for the bolts is 100 MPa. Assume each bolt supports an equal portion of the load. Determine the required diameter of the bolts. a. 20.6 mm b. 25.2 mm c.35.7 mm d.17.8 mm choose letter of correct answer
Need right complete solution
Determine the design tensile strength of plate (200x8 mm) connected to 10-mm thick gusset using 20 mm bolts as shown in the figure, if the yield and the ultimate stress of the steel used are 250 MPa and 410 MPa, respectively. Add 1mm around the bolt for the hole. Use LRFD method. Plate 8-mm thick 2 3 40+ 30 301 T 200 mm Gusset 10-mm thick 3af 30 2_3 *40 40+ 50,54 +40
The five-bolt connection shown must support an applied load of P = 330 kN. If the average shear stress in the bolts must be limited to 255 MPa, determine the minimum bolt diameter that may be used in the connection.
The following image shows a front and side view of the column connection. The bolts have a diameter of ¾”. The W12X65 profile has a thickness of 0.605”. Determine:a. The shear stress in the bolts.b. The axial stress in the bolts.c. The support stress in the W12X65 profile.
A bracket connection shown in figure, consists of a joist cutting welded to the flange of a column by shop fillet welds 8 mm on flanges and 6 mm on the web. Determine the safe service load 'W', the bracket can support at a distance of 200 mm from the face of the column if the steel grade is Fe 410. 200 200 8V 150 200 W 8 V 150 N 150 200 250 Partial factor of safety on shop weld = 1.25 Yield strength of steel = 250 MPa. 250 A