The A992 structural steel bar and a 2014-T6 aluminium bar shown below are secured to rigid supports at ends A and B and are connected together by a 1" diameter tool steel pin in double shear. The pin slides freely into place at room temperature. Determine the shearing stress on the pin caused by a 60 degree F drop in temperature and comment on its ability to carry the applied load.

The A992 structural steel bar and a 2014-T6 aluminium bar shown below are secured to rigid supports at ends A and B and are connected together by a 1" diameter tool steel pin in double shear. The pin slides freely into place at room temperature. Determine the shearing stress on the pin caused by a 60 degree F drop in temperature and comment on its ability to carry the applied load.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

pon 9.18 A steel rodin. in diameter and 25 ft long is subjected to an ace axial tensile load of 15,000 lb. Compute (a) stress ons Lanogsib & new (b) strain (c) total elongation aaste sviesiqmos srit nimmst gaites 900 viss srit .rwoda al
Problem2. The compression member is shown in figure. Find the following: a. The Euler stress Fe. b. The buckling stress Fcr c. The design strength d. The allowable strength e. Does the member satisfactorily meet the design requirements? Why? HSS 8x 8x4 ASTM AS00, Grade B steel (Fy = 46 ksi) 15'
Plastic stage is when all elements of a steel section is in yielding condition and reaches its utlimate strength before it collapses without lateral torsional buckling. O True O False
QI/ An aluminum bar carries the axial loads at the positions shown in Fig. 1, below. The diameter for part AB, BC and CD is 35 mm, 40 mm and 30 mm, respectively. The elastic modulus for aluminum is 72.4 x 10 N/mm. Determine the internal stresses at section (A-B), (B-C) and (C- D), and the elongation (AL) in length at each part of aluminum due to loading. в D 37 kN 10 kN 45 kN 18 kN 1000 mm 800 mm I 600 mm Fig. 1
The column above is subjected to axial loading only. Assume the following: • E= 29000 ksi G = 10000 ksi • = 986 in4 A = 60 in? • L= 20 ft • Grade 60 steel (60 ksi yield stress) • The column is fixed at the top and pinned at the bottom Which of the following is closest to the maximum normal stress the column can support (before yielding or buckling)? 167 ksi 24 ksi 42 ksi 60 ksi
Please show a detailed solution and explanation including its FBD. Thank you!
A 1.65m long rod with a circular cross-section is subjected to a tensile load of 50 kN. The rod is made from AISI 1040 hot-rolled steel. The allowable tensile stress is 165 MPa. The rod is permitted to elongate up to 7mm without causing any issues. The proportional limit for the steel is 180 MPa. (A) Compute the required area necessary to meet the stated requirements based on allowable stress. Express your answer in square millimeter units as an integer. (B) Compute the required area necessary to meet the stated requirements based on allowable elongation. Express your answer in square millimeter units as an integer.
Two T-shape sections are welded together to create a composite l-beam section as shown below. Determine the safely uniform load w (kN/m) that the beam can carry throughout its entire span. 270mm 30mm 20mm 160mm Welded Joint 130mm 30mm 135mm Beam Length = 4 m Consider the following stresses: fb(T) 3 125 МPа fb(C) = 130 MPa x at the welded joint = 20 MPa Find: 1. The Neutral Axis from the base 2. moment of inertia with respect to the horizontal centroidal axis 3. Q at the welded joint 4. Considering the maximum flexural stress in tension, WNAX is equal to KN/m. 5. Considering the maximum flexural stress in compression, WMAX, is equal to 6. Considering the stress at the welded joint, wMex is equal to kN/m.
Round off final ans only, dont round initial values
When designing a structural member, which of the following statements is FALSE? A. The allowable stress is used in calculating the maximum load to be applied. B. The ultimate stress depends on the Factor of Safety used. C. The ultimate stress is determined based on the material used. D. The allowable stress depends on how conservative the design is. Which of the following is NOT a valid reason for increasing the Factor of Safety? A. Higher uncertainty in loading conditions B. Higher design life C. Lower confidence in assumed/stated material properties D. Lower member importance Consider a 1,000-mm long, 25-mm diameter sample subjected to a tension test. Automatic high-precision gages recorded that for an applied load of 150 kN, the sample experienced a longitudinal strain of 2×10−3mm/mm. Assuming that the material remained elastic while loaded, determine its modulus of elasticity. A. 175.0 GPa B. 63.7 GPa C. 152.8 GPa D. 72.9 GPa
I need the answer as soon as possible