A steel plate is to be attached to a support with three bolts. The cross-sectional area of the plate is 800 mm² and the yield strength of the steel is 260 MPa. The ultimate shear strength of the bolts is 570 MPa. A factor of safety of 1.67 with respect to yield is required for the plate. A factor of safety of 4.0 with respect to the ultimate shear strength is required for the bolts. Determine the minimum bolt diameter required to develop the full strength of the plate. Note: consider only the gross cross-sectional area of the plate-not the net area. Support

A steel plate is to be attached to a support with three bolts. The cross-sectional area of the plate is 800 mm² and the yield strength of the steel is 260 MPa. The ultimate shear strength of the bolts is 570 MPa. A factor of safety of 1.67 with respect to yield is required for the plate. A factor of safety of 4.0 with respect to the ultimate shear strength is required for the bolts. Determine the minimum bolt diameter required to develop the full strength of the plate. Note: consider only the gross cross-sectional area of the plate-not the net area. Support

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q1: Choose the correct answer 1. If the control column slenderness (KL/r) for W12x72 section column equal to 47.73. The elastic critical buckling stress (F.) is a) 127.6 ksi b) 58.7 ksi c) 100 ksi 2. If the size of welding equal to 0.25" and length of weld equal to 5 then the value of ß is a) 0.8 b) 2 c) 1 3. If The tension member is a 4 in. x 3/8 in. thick rectangular bar. It is welded to a 1/2 in. thick gusset plate then the minimum size of welded is a)3/8" b) 1/2" c) none of a or b 4. If The tension member is a 4 in. x 3/8 in. thick rectangular bar. It is welded to a 1/2 in. thick gusset plate then the minimum size of welded is a)1/4" b) 7/16" c) none of a or b 5. If Fexx for used welded connector is 70 ksi then Fw is equal to b) 42 a) 18 c) 70
A fillet-welded joint is shown in the figure. The size of the weld is 8 mm. Safe stress in the weld is 110 N/mm². What is the safe force (to the nearest magnitude) to which the weld can be subjected? -80mm- 60 mm
A fillet-welded Joint of 6mm size is shown in the figure. The welded surfaces meet at 60-90 degree and permissible stress in the fillet weld is 108MPa. The safe load that can be transmitted by the joint is 100mm 50mm
Calculate the shear yield stress (ksi) of A588 steel.
Two steel plates are connected by a pair of splice plates with eight bolts as shown. The ultimate strength of the bolts is bolts is 270 MPa. An axial tension load of P = 480 kN is transmitted by the steel plates. If a factor of safety of 1.6 with respect to failure by fracture is specified, determine the minimum acceptable diameter "d" for the bolts. %3D P. splice plate steel steel plate plate (2) (1)
A fillet-welded joint is shown in the figure. The size of the weld is 8 mm. Safe stress in the weld is 110 N/mm². What is the safe force (to the nearest magnitude) to which the weld can be subjected? 80 mm 60 mm
An A36 steel plate with width of 400 mm and thickness of 12 mm is to beconnected to a plate of the same width and thickness by 34 mm diametersbolts, as shown in the figure (next slide). The holes are 2 mm larger thanthe bolt diameter. The yield strength of the steel plate is Fy = 248 MPa.Assume allowable tensile stress on net area is 0.60Fy. It is required todetermine the value of b such that the net width along bolts 1-2-3-4 isequal to the net width along bolts 1-2-4.a. Calculate the value of b in mm.b. Calculate the value of the net area for tension in plates in mm².c. Calculate the value of P so that the allowable tensile stress on net areawill not be exceeded.(Use at least 2 decimal points on your answers.)
Subject: Steel design- Bolted Steel Connection *Use NSCP 2015 formula/guide to solve this problem *Use Handwritten
Problem 4 Given two welded plates n A36 plates t= 3/ • fillet size w=1/4" Electrode Fexx= 70 ksi • plate width = 9" ● ● ↑ t=¾/2" = 2) = Pu= smaller of (1) A(2) w=1/4" Base Metal Strength, DRn is given by: ÞRn = 0.75(0.6Fu) (tBM)(Lw) t=3/8" Determine max Pu that can be applied to this connection ? hint: Dobtain Pue based on weld strength (transverse) BM strength = where tbm = thickness of the thinner connected plate Lw= length of the weld Fillet weld this side only i.e. lw= 9 in کہ ۔ Ри opy
Two plates are held together by 4, 10 mm diameter bolts. If a 26 kN load is applied to the plates in shear, what is the shear stress in the bolts in MPa? Type your answer...
PLEASE ANSWER THIS QUESTION ASAP!!!
CLO 1: For concentric rows of bolts in a coupling connection, the shear deformations in the bolts is proportional to the: O modulus of rigidity O diameter of bolt circle O radial distances O number of bolts