Problem 4.81 The 60-mm-diameter cylinder is made from Am 1004- T61 magnesium and is placed in the clamp when the temperature is T₁ = 20°C. (Figure 1) Part A If the 304-stainless-steel carriage bolts of the clamp each have a diameter of 9 mm, and they hold the cylinder snug with negligible force against the rigid jaws, determine the force in the cylinder when the temperature rises to T2= 130° C. Express your answer to three significant figures and include the appropriate units. F= Submit HA Value Units My Answers Give Up ? Provide Feedback Continue

Problem 4.81 The 60-mm-diameter cylinder is made from Am 1004- T61 magnesium and is placed in the clamp when the temperature is T₁ = 20°C. (Figure 1) Part A If the 304-stainless-steel carriage bolts of the clamp each have a diameter of 9 mm, and they hold the cylinder snug with negligible force against the rigid jaws, determine the force in the cylinder when the temperature rises to T2= 130° C. Express your answer to three significant figures and include the appropriate units. F= Submit HA Value Units My Answers Give Up ? Provide Feedback Continue

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter4: Compression Members

Section: Chapter Questions

Problem 4.9.3P

See similar textbooks

Similar questions

The 56-mm-diameter cylinder is made from Am 1004-T61 magnesium and is placed in the clamp when the temperature is T = 20°C. (Figure 1) Part A If the 304-stainless-steel carriage bolts of the clamp each have a diameter of 10 mm, and they hold the cylinder snug with negligible force against the rigid jaws, determine the force in the cylinder when the temperature rises to T, = 130°C. Express your answer to three significant figures and include the appropriate units. ? Figure 1 of 1 > Value Units Submit Request Answer < Return to Assignment Provide Feedback 100 mm 150 mm
10 mm 20 mm The assembly above is comprised of a 10mm-diameter steel bolt, and a 20mm-diameter, 2mm-thick bronze sleeve. The bolt and sleeve are rigidly connected at each end by a washer. Assume the following properties: Epolt = 29000 ksi &bolt = 6.6-106 1°F Vbolt = 0.35 Member BC is made of bronze with the following properties: Esleeve = 15000 ksi Xsleeve =9.80-106 /°F Vsleeve = 0.35 If the assembly is heated up, which of the following statements best describes how the sleeve will be affected? The sleeve will try to expand longitudinally, but will be restricted by the bolt (because the bolt has a lower coefficient of thermal expansion). The sleeve will go into tension and the bolt will go into compression. O The sleeve will try to expand longitudinally, but will be restricted by the bolt (because the bolt has a lower coefficient of thermal expansion). Both members will go into tension. The sleeve will try to expand longitudinally, but will be restricted by the bolt (because the bolt…
10/- find the bearing stress between bolts and plate 80 kN 80 kN 8-bolt DIA. 10 MM 80 kN 80 kN 8-bolt DIA. 10 MM 125 MPa 12.5 MPа О 250 MPа no one O 8 mm 300mm 3. 4) -O--O O 5,
4-47. The support consists of a solid red brass C83400 copper post surrounded by a 304 stainless steel tube. Before the load is applied the gap between these two parts is 1 mm. Given the dimensions shown, determine the greatest axial load that can be applied to the rigid cap A without causing yielding of any one of the materials. mm 0.25 m SOLUTION 60 mm -10 mm
For the clevis connection shown, determine the shear stress in the 23-mm-diameter bolt for an applied load of P = 165 kN. O 141 MPa O 211 MPa O 167 MPa O 120 MPa O 199 MPa Clevis
DO NO OWAVE www.oukpak.com F06 unic 30KN 150 KN 20KN 3m =30" SOLVE FOR ACL SUPPORT 2m HINGE REACTIONS LN DICATE THE DIRECTICNS e UNITC 20 A B im
The light rigid bar ABCD shown is pinned at C and connected to two vertical rods. The bar was initially horizontal, and the rods were stress-free before the load P= 20 KN is applied. Sleel E-200 GPa A-400mm L1 m 2.0 m 0.6 m 1.5m P-20 KN Aluminum E70 GPa A-900mm L-1.5 m 1. Axial load at steel rod in kN? 2. Axial stress at steel rod in MPa? 3. Axial deformation of aluminum rod in mm? 4. Axial deformation of steel rod in mm? 5. Axial Load at aluminum rod in kN?
Need urgent and correct solution
The welded frame beam connection consists of the framing angle 100 x 75 x12.5mm and the column W12 x 72. The welds are 9mm fillet welds made with E70 electrodes. All members are A36 steel. 12.5 mm a.) Determine Pu base on the capacity of the welds. Use LRFD design Factors. W 12x72 Angular Section 75 m 18.75 18.75 Angular section Angular section 800
9. The gusset shown is riveted to the column flange by 7-20mm diameter rivet single shear. Determine the stress in the most heavily loaded bolt. If the design shear stress is 400MPA, determine the ultimate load that the connections can carry. Using the design shear stress how much more torque can the connections carry? 140 kN 200 mm 175 mm 7- 20 mm bolts 150 mm 150 mm 150 mm
The light rigid bar ABCD shown is pinned at C and connected to two vertical rods. The bar was initially horizontal, and the rods were stress-free before the load P = 20 KN is applied. Steel E200 Gra A-600mm L-I m 2.0 m 0.6m 1.5 m D. V P-20 KN Aluminum E-70 GPa A-900mm L-1.5 m What is the axial load at aluminum rod in KN?
The 54-mm-diameter cylinder is made from Am 1004-T61 magnesium and is placed in the clamp when the temperature is T₁ = 20°C. (Figure 1) Figure 100 mm If the 304-stainless-steel carriage bolts of the clamp each have a diameter of 10 mm, and they hold the cylinder snug with negligible force against the rigid jaws, determine the force in the cylinder when the temperature rises to T₂ = 130°C. Express your answer to three significant figures and include the appropriate units. F = 843.6 Submit Л Templates Symbols undo rado reset keyboard shortcuts help 1 * N 150 mm www. < 1 of 1 Previous Answers Request Answer