14-12 A beam with an inverted T-section is subjected to the two concentratedloads shown in Fig. P14-12. Determine the maximum tensile and compres-sive stresses in the beam. Neglect the weight of the beam.40 KN20 kNללית2 ms2 mכללית1m-25 mm200 mm150 mm25 mmSection

Answered: Image /qna-images/answer/e27dccc1-8592-458a-8272-eeabbb81af6a.jpg

Answered: 14-12 A beam with an inverted T-section…

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.8.1P: Compute the nominal shear strength of an M107.5 of A572 Grad 65 steel.

See similar textbooks

Similar questions

The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
A tensile test was performed on a metal specimen having a circular cross section with a diameter 0. 510 inch. For each increment of load applied, the strain was directly determined by means of a strain gage attached to the specimen. The results are, shown in Table: 1.5.1. a. Prepare a table of stress and strain. b. Plot these data to obtain a stress-strain curve. Do not connect the data points; draw a best-fit straight line through them. c. Determine the modulus of elasticity as the slope of the best-fit line.
A tensile test was performed on a metal specimen with a diameter of 1 2 inch and a gage length (the length over which the elongation is measured) of 4 inches. The dam were plotted on a load-displacement graph. P vs. L. A best-fit line was drawn through the points, and the slope of the straight-line portion was calculated to be P/L =1392 kips/in. What is the modulus of elasticity?
using Figure 5-27, what is the advantage of the suspended type magnet over the other two types of magnets?
A beam is part of the framing system for the floor of an office building. The floor is subjected to both dead loads and live loads. The maximum moment caused by the service dead load is 45 ft-kips, and the maximum moment for the service live load is 63 ft-kips (these moments occur at the same location on the beam and can therefore be combined). a. If load and resistance factor design is used, determine the maximum factored bending moment (required moment strength). What is the controlling AISC load combination? b. What is the required nominal moment strength for a resistance factor of 0.90? c. If allowable strength design is used, determine the required moment strength. What is the controlling AISC lead combination? d. What is the required nominal moment strength for a safety factor of 1.67?
Use an elastic analysis and determine the maximum load in the weld (in kips per inch of length).
The given beam is laterally supported at the ends and at the 1 3 points (points 1, 2, 3, and 4). The concentrated load is a service live load. Use Fy=50 ksi and select a W-shape. Do not check deflections. a. Use LRFD. b. Use ASD.
A beam must be designed to the following specifications: Span length = 35 ft Beam spacing = 10 ft 2-in. deck with 3 in. of lightweight concrete fill (wc=115 pcf) for a total depth of t=5 in. Total weight of deck and slab = 51 psf Construction load = 20 psf Partition load = 20 psf Miscellaneous dead load = 10 psf Live load = 80 psf Fy=50 ksi, fc=4 ksi Assume continuous lateral support and use LRFD. a. Design a noncomposite beam. Compute the total deflection (there is no limit to be checked). b. Design a composite beam and specify the size and number of stud anchors required. Assume one stud at each beam location. Compute the maximum total deflection as follows: 1. Use the transformed section. 2. Use the lower-bound moment of inertia.

Recommended textbooks for you

Steel Design (Activate Learning with these NEW ti…

Civil Engineering

ISBN:

9781337094740

Author:

Segui, William T.

Publisher:

Cengage Learning

Solid Waste Engineering

Civil Engineering

ISBN:

9781305635203

Author:

Worrell, William A.

Publisher:

Cengage Learning,

Materials Science And Engineering Properties

Civil Engineering

ISBN:

9781111988609

Author:

Charles Gilmore

Publisher:

Cengage Learning

Steel Design (Activate Learning with these NEW ti…

Civil Engineering

ISBN:

9781337094740

Author:

Segui, William T.

Publisher:

Cengage Learning

Solid Waste Engineering

Civil Engineering

ISBN:

9781305635203

Author:

Worrell, William A.

Publisher:

Cengage Learning,

Materials Science And Engineering Properties

Civil Engineering

ISBN:

9781111988609

Author:

Charles Gilmore

Publisher:

Cengage Learning

Residential Construction Academy: House Wiring (M…

Civil Engineering

ISBN:

9781285852225

Author:

Gregory W Fletcher

Publisher:

Cengage Learning

Engineering Fundamentals: An Introduction to Engi…

Civil Engineering

ISBN:

9781305084766

Author:

Saeed Moaveni

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

14-12 A beam with an inverted T-section is subjected to the two concentrated loads shown in Fig. P14-12. Determine the maximum tensile and compres- sive stresses in the beam. Neglect the weight of the beam. 40 KN 20 kN ללית 2 ms 2 m כללית 1m- 25 mm 200 mm 150 mm 25 mm Section