Please answer the question in the picture and show all of your work. Thank you so much for your help! Q2 RiserYou are asked to determine the discharge from a riser located within a detention basin that willreduce peak flows downstream.The riser is 15 feet tall with 5 square openings located at the base of the reservoir. The openingsare each 2 feet by 2 feet. Determine the flowrate leaving the reservoir when the depth of flow is 9feet.Cd = 0.62 and Cw = 3.1Please enter your answer to the nearest ones place. Please enter it as a numeric value only andplease omit units.

Given Data:- Cd = 0.62 Cw = 3.1 Depth of flow = 9 ft The opening are 2 feet by 2 fee Solution…

Answered: Q2 Riser You are asked to determine the…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Pls answer asap. What is the maximum discharge of a semi-hexagonal shape having a channel bed width of 3 m flowing at a depth of 1.2 m and with a velocity 4.0 m/s ? Write your answer to the nearest whole number.
From the given three reservoirs, the elevation of A is 345m, B is at elevation 300m, and C is at elevation 240m. The rate of flow at 1 is 300li/sec. A. Compute the headloss in pipeline 2 B. Compute the discharge in pipeline 3 C. Compute the diameter of pipeline 3 Location of pipe Reservoir A to junction X Length (m) 600 Pipe no Diameter (mm) HAZENS (C) 1 450 120 Junction X to Reservoir B 2 3600 300 100 Junctin x to Reservoir C 3 1250 ? 110
You are responsible for calculating the peak discharge for a culvert design in a smallwatershed in Washington, DC. The watershed area is 4 acres and currently has 30 % of its area ofindustrial (heavy areas) and 70 % of residential (single –family areas). The design manual suggestsyou design your culvert for a 10 return period. The watershed has a concentration time of2 hours. Calculate:a) What is the design peak flow?b) What is the impact of the runoff coefficient (C) range on your design?c) After you implemented your project, the residential area was entirely converted toindustrial areas. Would that affect you design? If yes, by how much?
do not round off everything
Problem 7 - 64 Determine the flow in each pipe in the figure shown and the elevation of reservoir C if the inflow to reservoir A is 515 Lit/sec. Problem 7-64 with the following conditions: - inflow at reservoir A = 600 Ips - roughness coefficient for all pipes = 0.05 - elevation B = 92m
Three reservoirs A, B and C whose water surface elevations are 60ft, 50ft and 32 ft respectively, are interconnected by a pipe system with a common junction at elevation 35ft. All pipes have a frictional factor of 0.020 and are as described as follows 1. Illustrate the problem 2. What is the direction of flow into reservoir B? 3. Determine the flow from reservoir B in ft^3/s. Indicate if it is Toward or away from junction D. 4. Determine the flow from reservoir C in ft^3/s. Indicate if it is Toward or away from junction D.
As a field engineer you are tasked to estimate the 25-year peak discharge for concrete parking lot that is 310 feet wide by 600 feet long using Rational formula. The longest flow path is 310 feet of sheet flow across the lot on a slope of 0.005 and 600 feet of shallow concentrated flow along the parking lot's length in a paved channel on a slope of 0.015. Use SCS procedures to determine the time of concentration using a 2-year, 24-hr rainfall of 2.4 inches. Use Figure below for the rainfall intensity in the rational equation. Intensity (in/hr) 0 10 20 25-yr average frequency 10-yr average frequency 30 40 -5-yr average frequency 2-yr average frequency 50 60 70 80 90 100 110 120 Duration (min)
T t + 1. Flow 3LH 3/2 2. Length = 70 ft 3. Crest height = 60 ft Hydrology HW1// Route the flood hydrograph indicated below through a reservoir. The storage (elevation versus volume) data obtained from the reservoir survey are given. The spillway has the following characteristics: • Flood Routing • Reservoir Routing • HW1// (1 = புர் ||| Prepared by Dr Nabil Al Amery Inflow Time (hr) Flow (cfs) 0 0.4 0.8 1.2 1.6 2 2.4 2.8 3.2 3.6 0 600 2100 2500 1600 950 550 300 80 0 فلاتر O 4th year civil engineering class Storage Date Elevation Storage (ft) (acre ft) 60 61 62 63 64 65 300 330 360 395 430 470 × إضافة شرح... > mum
Determine the characteristics of a unit composed of 2 desilting channels treating a peak wastewater flow of 1500 L7s. A surface load of 40 m/h is assumed. The effective head or depth "P" is set at 1.5 m. Calculate: 1. Area of each channel 2. 2. Effective volume of each desanding channel 3. HRT 4. Cross-sectional area of each desanding channel 5. 5. Width of each channel.
please answer ASAP
a) Concern has been expressed at the local waste water treatment plant regarding the overflows caused by storm water being passed down the same pipeline. The town area main drain has to deal with a maximum of 100m3/s approximately twice a year and so it is proposed that a single drain pipe capable of taking this volume of water be collected from the main storm drains into a temporary storage reservoir to be channelled into the river.The maximum head available is 22m. The pipe is 2050m long, the Darcey Weisbach figure is 0.011, what is the minimum pipe diameter for this project? b) Looking into the future with mean temperature levels exceeding 2.50C above pre-industrial levels it is considered that the maximum size of the water drain pipe would increase by 4m3/second every decade . Provide a table of expected maximum drain loads over a period from 2030 to 2130 and plot this on a graph. You are advised to plot the maximum expected rainfall against pipe diameter. c)(i) Explain briefly how…
A municipal wastewater treatment plant (WWTP) receives a flow of 5.0 MGD. The WWTP does not have an equalization basin and therefore can have a peak hour flow that is 2.5 times the average daily flow. The WWTP has two circular, upflow clarifiers operating in parallel. The clarifiers must be designed to meet the following conditions: 1,000 gpd/ft (maximum) Average overflow rate = Peak overflow rate = 2,500 gpd/ft° (maximum) Basin depth = 10 ft What is the diameter of each primary clarifier? Hint: calculate the diameter for each a. of the given conditions, and select your diameter based on your results.

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS