cisco.practicetest.300-410.vce.dumps.2023-dec-03.by.bill.406q.vce

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) NEW QUESTION 1 - (Exam Topic 3) A network administrator must optimize the segment size of the TCP packet on the DMVPN IPsec protected tunnel interface, which carries application traffic from the head office to a designated branch. The TCP segment size must not overwhelm the MTU of the outbound link. Which configuration must be applied to the router to improve the application performance? A. Option A B. Option B C. Option C D. Option D Answer: C NEW QUESTION 2 - (Exam Topic 3) Refer to the exhibit. Which two commands provide the administrator with the information needed to resolve the issue? (Choose two.) A. snmp user B. debug snmp engine-id C. debug snmpv3 engine-id D. debug snmp packet E. showsnmpv3 user Answer: AE NEW QUESTION 3 - (Exam Topic 3) An engineer configures PBR on R5 and wants to create a policy that matches traffic destined toward 10.10.10.0/24 and forward 10.1.1.1. The traffic must also have its IP precedence set to 5.All other traffic should be forward toward 10.1.1.2 and have its IP precedence set to 0.Which configuration meets the requirements? A. access-list 1 permit 10.10.10.0 0.0.0.255 access-list 2 permit anyroute-map CCNP permit 10 match ip address 1set ip next-hop 10.1.1.1 set ip precedence 5!route-map CCNP permit 20 match ip address 2set ip next-hop 10.1.1.2set ip precedence 0route-map CCNP permit 30 B. access-list 100 permit ip any 10.10.10.0 0.0.0.255 route-map CCNP permit 10match ip address 100 set ip next-hop 10.1.1.1 set ip precedence 0!route-map CCNP permit 20 set ip next-hop 10.1.1.2set ip precedence 5!route-map CCNP permit 30 C. access-list 1 permit 10.10.10.0 0.0.0.255 route-map CCNP permit 10match ip address 1set ip next-hop 10.1.1.1set ip precedence 5!route-map CCNP permit 20 set ip next-hop 10.1.1.2set ip precedence 0 D. access-list 100 permit ip any 10.10.10.0 0.0.0.255 route-map CCNP permit 10match ip address 100 set ip next-hop 10.1.1.1 set ip precedence 5!route-map CCNP permit 20 set ip next-hop 10.1.1.2set ip precedence 0 Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) NEW QUESTION 10 - (Exam Topic 3) The network administrator configured CoPP so that all HTTP and HTTPS traffic from the administrator device located at 172.16 1.99 toward the router CPU is limited to 500 kbps. Any traffic that exceeds this limit must be dropped. access-list 100 permit ip host 172.16.1.99 any ! class-map CM-ADMIN match access-group 100 ! policy-map PM-COPP class CM-ADMIN police 500000 conform-action transmit ! interface E0/0 service-policy input PM-COPP CoPP failed to capture the desired traffic and the CPU load is getting higher. Which two configurations resolve the issue? (Choose two.) A. interface E0/0no service-policy input PM-COPP!control-planeservice-policy input PM-COPP B. policy-map PM-COPP class CM-ADMINno police 500000 conform-action transmit police 500 conform-action transmit!control-planeservice-policy input PM- COPP C. no access-list 100access-list 100 permit tcp host 172.16.1.99 any eq 80 D. no access-list 100access-list 100 permit tcp host 172.16.1.99 any eq 80access-list 100 permit tcp host 172.16.1.99 any eq 443 E. policy-map PM-COPP class CM-ADMINno police 500000 conform-action transmit police 500 conform-action transmit Answer: A NEW QUESTION 10 - (Exam Topic 3) Which router translates the customer routing information into VPNv4 routes to exchange VPNv4 routes with other devices through MP-BGP? A. PE B. CE C. P D. VPNv4 RR Answer: A NEW QUESTION 12 - (Exam Topic 3) Refer to the exhibit. An engineer is troubleshooting failed access by contractors to the business application server via Telnet or HTTP during the weekend. Which configuration resolves the issue? A) B) C) D) Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) can be removed. D. An extended access list must be used instead of a standard access list to accomplish the task Answer: C NEW QUESTION 18 - (Exam Topic 3) Refer to the exhibit. The network administrator must configure Cape Town to reach Dubai via Tokyo based on the speeds provided by the service provider. It was noticed that Cape Town is reaching Dubai directly and failed to meet the requirement. Which configuration fixes the issue? A) B) C) D) Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) An engineer configures DMVPN and receives the hub location prefix of 10.1.1.0724 on R2 and R3 The R3 prefix of 10 1.3.0/24 is not received on R2. and the R2 prefix 10.1,2.0/24 is not received on R3. Which action reserves the issue? A. Split horizon prevents the routes from being advertised between spoke routers it should be disabled with the command no ip split-horizon eigrp 10 on the tunnel interface of R1 B. There is no spoke-to-spoke connection DMVPN configuration should be modified to enable a tunnel connection between R2 and R3 and neighbor relationship confirmed by use of the show ip eigrp neighbor command C. Split horizon prevents the routes from being advertised between spoke routers it should be disabled with the no ip split-horizon eigrp 10 command on the Gi0/0 interface of R1. D. There is no spoke-to-spoke connection DMVPN configuration should be modified with a manual neighbor relationship configured between R2 and R3 and confirmed bb use of the show ip eigrp neighbor command. Answer: A Explanation: In this topology, the Hub router will receive advertisements from R2 Spoke router on its tunnel interface. The problem here is that it also has a connection with R3 Spoke on that same tunnel interface. If we don’t disable split-horizon, then the Hub will not relay routes from R2 to R3 and the other way around. That is because it received those routes on the same interface tunnel and therefore it cannot advertise back out that same interface (split-horizon rule). Therefore we must disable splithorizon on the Hub router to make sure the Spokes know about each other. NEW QUESTION 36 - (Exam Topic 3) What is a function of BFD? A. peer recovery after a Layer 3 protocol adjacency failure B. peer recovery after a Layer 2 adjacency failure C. failure detection independent of routing protocols and media types D. failure detection dependent on routing protocols and media types Answer: D NEW QUESTION 40 - (Exam Topic 3) Refer to the exhibit. A network administrator is troubleshooting OSPF adjacency issue by going through the console logs in the router, but due to an overwhelming log message stream it is impossible to capture the problem Which two commands reduce console log messages to relevant OSPF neighbor problem details so that the issue can be resolved? (Choose two) A. debug condition interface B. debug condition ip C. debug condition ospf neighbor D. debug condition session-id ADJCHG E. debug condition all Answer: AD NEW QUESTION 44 - (Exam Topic 3) What is considered the primary advantage of running BFD? A. reduction in time needed to detect Layer 2 switched neighbor failures B. reduction in time needed to detect Layer 3 routing neighbor failures C. reduction in CPU needed to detect Layer 2 switch neighbor failures D. reduction in CPU needed to detect Layer 3 routing neighbor failures Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) Refer to the exhibit. An engineer configured NetFlow on R1, but the flows do not reach the NMS server from R1. Which configuration resolves this Issue? A. Option A B. Option B C. Option C D. Option D Answer: B NEW QUESTION 62 - (Exam Topic 3) Refer to the exhibit. An engineer configured two ASBRs, 10.4.17.6 and 10.4.15.5, in an OSPF network to redistribute identical routes from BGR However, only prefixes from 10.4.17.6 are installed into the routing table on R1. Which action must the engineer take to achieve load sharing for the BGP-originated prefixes? A. The ASBRs are advertising the redistributed prefixes with the iBGP metric and must be modified to Type 1 on ASBR 10.4.17.6. B. The ASBRs are advertising the redistributed prefixes with a different admin distance and must be changed to 110 on ASBR 10.4.15.5. C. The admin distance of the prefixes must be adjusted to 20 on ASBR 10.4.15.5 to advertise prefixes to R1 identically from both ASBRs. D. The ASBRs are advertising the redistributed prefixes as Type 1 and must be modified to Type 2 Answer: D NEW QUESTION 66 - (Exam Topic 3) Refer to the exhibit. Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) Refer to the exhibit. A network is configured for EIGRP equal-cost load balancing, but the traffic destined to the servers is not load balanced. Link metrics from router R2 to R3 and R4 are the same. Which delay value must be configured to resolve the issue? A. 208 oon R3 E0/0 B. 120 on R4 E0/1 C. 120/on R3 E0/1 D. 2200 on R4 E0/1 Answer: C NEW QUESTION 82 - (Exam Topic 3) What are two characteristics of IPv6 Source Guard? (Choose two.) A. requires IPv6 snooping on Layer 2 access or trunk ports B. used in service provider deployments to protect DDoS attacks C. requires the user to configure a static binding D. requires that validate prefix be enabled E. recovers missing binding table entries Answer: DE Explanation: IPv6 Source Guard uses the IPv6 First-Hop Security Binding Table to drop traffic from unknown sources or bogus IPv6 addresses not in the binding table. The switch also tries to recover from lost address information, querying DHCPv6 server or using IPv6 neighbor discovery to verify the source IPv6 address after dropping the offending packet(s). Reference: https://blog.ipspace.net/2013/07/first-hop-ipv6-security-features-in.html NEW QUESTION 85 - (Exam Topic 3) An engineer received a ticket about a router that has reloaded. The monitoring system graphs show different traffic patterns between logical and physical interfaces when the router is rebooted. Which action resolves the issue? A. Configure the snmp ifindex persist command globally. B. Clear the logical interfaces with snmp ifindex clear command C. Configure the snmp ifindex persist command on the physical interfaces. D. Trigger a new snmpwalk from the monitoring system to synchronize interface OlDs Answer: A Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) Refer to the exhibit A network engineer received a call from the vendor for a failed attempt to remotely log in to their managed rooter loopback interface from 192 168.40 15 Which action must the network engineer take to resolve the issue? A. The IP access list VENDOR must be applied to interface loopback 100 B. The time-range configuration must be changed to use absolute instead of periodic C. The EIGRP configuration must be updated to include a network statement for loopback 100 D. The source IP summarization must be updated to include the vendor source IP address Answer: C NEW QUESTION 106 - (Exam Topic 3) Which two technologies optimize MPLS infrastructure using bandwidth protection services when experiencing slow response7 (Choose two.) A. IPLFA B. MPLS OAM C. VPLS D. SO-MPLS E. Fast-Rwoute Answer: AE NEW QUESTION 109 - (Exam Topic 3) Refer to the exhibit. Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) An engineer is troubleshooting a failed Telnet session from PC to the DHCP server. Which action resolves the issue? A. Remove sequence 30 and add it back to the IPv6 traffic filter as sequence 5. B. Remove sequence 20 and add it back to the IPv6 traffic filter as sequence 5. C. Remove sequence 10 to add the PC source IP address and add it back as sequence 10. D. Remove sequence 20 for sequence 40 in the access list to allow Telnet. Answer: B NEW QUESTION 112 - (Exam Topic 3) What are two characteristics of a VRF instance? (Choose two) A. It is defined by the VPN membership of a customer site attached to a P device. B. Each VRF has a different set of routing and CEF tables. C. AII VRFS share customers routing and CEF tables. D. An interface must be associated to one VRF E. A customer site can be associated to different VRFs. Answer: BD NEW QUESTION 115 - (Exam Topic 3) Which IPv6 first hop security feature controls the traffic necessary for proper discovery of neighbor device operation and performance? A. RA Throttling B. Source or Destination Guard C. ND Multicast Suppression D. IPv6 Snooping Answer: D NEW QUESTION 117 - (Exam Topic 3) Refer to the exhibit. Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) An engineer implemented CoPP to limit Telnet traffic to protect the router CPU. It was noticed that the Telnet traffic did not pass through CoPP Which configuration resolves the issue? A. Option A B. Option B C. Option C D. Option D Answer: D NEW QUESTION 121 - (Exam Topic 3) Refer to the exhibit. A network administrator must configure DMVPN tunnels between the hub and spoke with dynamic spoke-to-spoke tunnel capabilities using EIGRP. Which tunnel interface command must the network administrator configure to establish an EIGRP peer? A. no ip next-hop-self eigrp 1 B. ip next-hop-self eigrp 1 C. no Ip nhrp ntxt-hop-self D. ip nhrp next-hop-self Answer: C NEW QUESTION 125 - (Exam Topic 3) Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) Refer to the exhibit Which action ensures that 10 10 10 0/24 reaches 10 10 20 0/24 through the direct link between R1 and R2? A. Configure R1 and R2 LAN links as nonpassive. B. Configure R1 and R2 links under area 1 C. Configure OSPF link cost to 1 between R1 and R2 D. Configure OSPF path cost to 3 between R1 and R2 Answer: B NEW QUESTION 130 - (Exam Topic 3) Which IPv6 feature enables a device to reject traffic when it is originated from an address that is not stored in the device binding table? A. IPv6 Snooping B. IPv6 Source Guard C. IPv6 DAD Proxy D. IPv6 RA Guard Answer: B Explanation: https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/ipv6_fhsec/configuration/xe-3s/ip6f-xe-3s-book/ip6-src-guar NEW QUESTION 134 - (Exam Topic 3) Refer to the exhibit. Packets arriving from source 209.165.200.215 must be sent with the precedence bit set to 1, and packets arriving from source 209.165.200.216 must be sent with the precedence bit set to 5. Which action resolves the issue? A. set ip precedence critical in route-map Texas permit 10 B. set ip precedence critical in route-map Texas permit 20 C. set ip precedence immediate in route-map Texas permit 10 D. set ip precedence priority in route-map Texas permit 20 Answer: B NEW QUESTION 135 - (Exam Topic 3) Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) Refer to the exhibit. An engineer must configure a per VRF for TACACS+ for company A. Which configuration on RTG-1 accomplishes the task? A. Option A B. Option B C. Option C D. Option D Answer: D NEW QUESTION 139 - (Exam Topic 3) Refer to the exhibit. Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) An engineer must block access to the console ports for all corporate remote Cisco devices based on the recent corporate security policy but the security team stilt can connect through the console port. Which configuration on the console port resolves the issue? A. transport input telnet B. login and password C. no exec D. exec 0.0 Answer: C Explanation: “no exec” will disable access to a line. It is used if we want to allow only outgoing session (and disable incoming session) so this command will block all console port access. There is no “exec 0 0” command. We can only find the “exec prompt” command in IOS Version 15.4(2)T4. The most similar command is “exec-timeout 0 0” command, which is used to prevent Telnet/SSH sessions from timing out. NEW QUESTION 141 - (Exam Topic 3) Which control plane process allows the MPLS forwarding state to recover when a secondary RP takes over from a failed primary RP? A. MP-BGP uses control plane services for label prefix bindings in the MPLS forwarding table B. LSP uses NSF to recover from disruption *i control plane service C. FEC uses a control plane service to distribute information between primary and secondary processors D. LDP uses SSO to recover from disruption in control plane service Answer: C NEW QUESTION 146 - (Exam Topic 3) An engineer configured VRF-Lite on a router for VRF blue and VRF red. OSPF must be enabled on each VRF to peer to a directly connected router in each VRF. Which configuration forms OSPF neighbors over the network 10.10.10.0/28 for VRF blue and 192.168.0.0/30 for VRF red? A. Option A B. Option B C. Option C D. Option D Answer: A Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) NEW QUESTION 150 - (Exam Topic 3) Refer to the exhibit. The network administrator configured the network to establish connectivity between all devices and notices that the ASBRs do not have routes for each other. Which set of configurations resolves this issue? A. Option A B. Option B C. Option C D. Option D Answer: D NEW QUESTION 152 - (Exam Topic 3) A network administrator is trying to access a branch router using TACACS+ username and password credentials, but the administrator cannot log in to the router because the WAN connectivity is down. The branch router has following AAA configuration: Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) Which command will resolve this problem when WAN connectivity is down? A. aaa authentication login default group tacacs+ local B. aaa authentication login default group tacacs+ enable C. aaa authentication login default group tacacs+ console D. aaa authentication login console group tacacs+ enable Answer: A Explanation: With the “aaa authentication login default group tacacs+ local ” command configured, when logging in, the password supplied will be attempted to be verified by the TACACS+ server before access is granted. If the server is unavailable/unreachable, then the switch will fall back to using the local authentication database. NEW QUESTION 156 - (Exam Topic 3) Refer to the exhibit. R1 is configured with IP SLA to check the availability of the server behind R6 but it kept failing. Which configuration resolves the issue? A. R1(config)# ip sla 700R1(config-track)# delay down 30 up 20 B. R1(config)# ip sla 700R1(config-track)# delay down 20 up 30 C. R1(config)# track 700 ip sla 700 R1(config-track)# delay down 30 up 20 D. R1(config)# track 700 ip sla 700 R1(config-track)# delay down 20 up 30 Answer: C NEW QUESTION 158 - (Exam Topic 3) Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) Refer to the exhibit A company builds WAN infrastructure between the head office and POPs using DMVPN hub-and-spoke topology to provide end-to-end communication All POPs must maintain point-to-point connectivity with the head office Which configuration meets the requirement at routers R12 and R13? A. Option A B. Option B C. Option C D. Option D Answer: D NEW QUESTION 159 - (Exam Topic 3) Refer to the exhibit. Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) An engineer must advertise routes into IPv6 MP-BGP and failed. Which configuration resolves the issue on R1? A. router bgp 65000no bgp default ipv4-unicast address-family ipv6 multicast network 2001:DB8::/64 B. router bgp 65000no bgp default ipv4-unicast address-family ipv6 unicast network 2001:DB8::/64 C. router bgp 64900no bgp default ipv4-unicast address-family ipv6 unicast network 2001:DB8::/64 D. router bgp 64900no bgp default ipv4-unicast address-family ipv6 multicastneighbor 2001:DB8:7000::2 translate-update ipv6 multicast Answer: B NEW QUESTION 164 - (Exam Topic 3) A DMVPN network is preconfigured with tunnel 0 IP address 192.168.1.254 on the HUB, IP connectivity, crypto policies, profiles, and EIGRP AS 100. The NHRP password is ccnp123, and the network ID and tunnel key is EIGRP ASN Do not introduce a static route. Configure DMVPN connectivity between routers BR1 and BR2 to the HUB router using physical interface as the tunnel source to achieve these goals: Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) A. Mastered B. Not Mastered Answer: A Explanation: ON BR1 ON BR2 Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) NEW QUESTION 169 - (Exam Topic 3) Refer to the exhibit. An engineer is trying to connect to R1 via Telnet with no success. Which configuration resolves the issue? A. Option A B. Option B C. Option C D. Option D Answer: B Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) NEW QUESTION 171 - (Exam Topic 3) Refer to the exhibit. After reloading the router an administrator discovered that the interface utilization graphs displayed inconsistencies with their previous history in the NMS. Which action prevents this issue from occurring after another router reload in the future? A. Rediscover all the router interfaces through SNMP after the router is reloaded B. Save the router configuration to startup-config before reloading the router C. Configure SNMP to use static OlDs referring to individual router interfaces D. Configure SNMP interface index persistence on the router Answer: D NEW QUESTION 173 - (Exam Topic 3) Refer to the exhibit The route to 192 168 200 0 is flapping between R1 and R2 Which set of configuration changes resolves the flapping route? A. Option A B. Option B Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) C. Option C D. Option D Answer: D NEW QUESTION 178 - (Exam Topic 3) The network administrator is tasked to configure R1 to authenticate telnet connections based on Cisco ISE using RADIUS. ISE has been configured with an IP address of 192.168.1.5 and with a network device pointing towards R1 (192.168.1.1) with a shared secret password of Cisco123. If ISE is down, the administrator should be able to connect using the local database with a username and password combination of admin/cisco123. The administrator has configured the following on R1: ISE has gone down. The Network Administrator is not able to Telnet to R1 when ISE went down. Which two configuration changes will fix the issue? (Choose two.) A. Option A B. Option B C. Option C D. Option D E. Option E Answer: CE NEW QUESTION 182 - (Exam Topic 3) A network administrator is troubleshooting a failed AAA login issue on a Cisco Catalyst c3560 switch. When the network administrator tries to log in with SSH using TACACS+ username and password credentials, the switch is no longer authenticating and is failing back to the local account. Which action resolves this issue? A. Configure ip tacacs source-interface GigabitEthernet 1/1 B. Configure ip tacacs source-ip 192.168.100.55 C. Configure ip tacacs-server source-ip 192.168.100.55 D. Configure ip tacacs-server source-interface GigabitEthernet 1/1 Answer: A NEW QUESTION 183 - (Exam Topic 3) Refer to the exhibit. Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) An engineer configures SW101 to send OSPFv3 interfaces state change messages to the server. However, only some OSPFv3 errors are being recorded. which organization resolves the ..? A. snmp-server enable traps ospfv3 state-change if-state-change B. snmp-server-enable traps ospfv3 state-change restart-status-change C. snmp-server-enable traps ospfv3 state-change neighbor-state-change. D. snmp-server-enable traps ospfv3 state-change if-state-change neighbor-state-change Answer: D NEW QUESTION 188 - (Exam Topic 3) Refer to the exhibit. Spoke routers do not learn about each other's routes in the DMVPN Phase2 network. Which action resolves the issue? A. Remove default route from spoke routers to establish a spoke-to-spoke tunnel. B. Configure a static route in each spoke to establish a spoke-to-spoke tunnel. C. Rectify incorrect wildcard mask configured on the hub router network command. D. Disable EIGRP split horizon on the TunnelO interface of the hub router. Answer: D NEW QUESTION 192 - (Exam Topic 3) Refer to the exhibit. Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) An administrator configures a router to stop using a particular default route if the DNS server 8.8.8.8 is not reachable through that route. However, this configuration did not work as desired and the default route still works even if the DNS server 8.8.8 8 is unreachable. Which two configuration changes resolve the issue? (Choose two.) A. Configure two static routes for the 8.8.8.8/32 destination to match the IP SLA probe for each ISP. B. Associate every IP SLA probe with the proper WAN address of the router. C. Reference the proper exit interfaces along with the next hops in both static default routes. D. Use a separate track object to reference the existing IP SLA 1 probe for every static route. E. Use a separate IP SLA probe and track object for every static route Answer: AE NEW QUESTION 193 - (Exam Topic 3) Refer to the exhibit. A customer reports that user traffic of bank XYZ to the AAA server is not using the primary path via the R3-R2 link. The network team observes: No fiber is cut on links R2 and R3. As101 and AS 201 routers established BGP peering. Which configuration resolves the issue? Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) A. Option A B. Option B C. Option C D. Option D Answer: A NEW QUESTION 194 - (Exam Topic 3) Refer to the exhibit. An engineer configured SNMP communities on the Core_SW1, but the SNMP server cannot obtain information from Core_SW1. Which configuration resolves this issue? A. snmp-server group NETVIEW v2c priv read NETVIEW access 20 B. access-list 20 permit 10.221.10.11 C. access-list 20 permit 10.221.10.12 D. snmp-server group NETADMIN v3 priv read NETVIEW write NETADMIN access 22 Answer: B NEW QUESTION 196 - (Exam Topic 3) What are the two reasons for RD and VPNv4 addresses in an MPLS Layer 3 VPN? (Choose two.) A. RD is prepended to each prefix to make routes unique. B. VPN RT communities are used to identify customer unique routes. C. When the PE redistributes customer routes into MP-BGP, they must be unique. D. They are on a CE device to use for static configuration. Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) E. They are used for a BGP session with the CE device. Answer: AC NEW QUESTION 201 - (Exam Topic 3) Refer to the exhibit. After a new regional office is set up,not all guests can access the internet via guest WiFi. Clients are getting the correct IP address from guest Wi-Fi VLAN 364. which action resolves the issue ? A. Allow 10.66.46.0/23 in the outbound ACL B. Allow DNS traffic through the outbound ACL C. Allow DNS traffic through the inbound ACL D. Allow 10.66.46.0/23 in the inbound ACL Answer: C NEW QUESTION 206 - (Exam Topic 3) Refer to the exhibit. The connected routers do not show up as OSPF neighbors. Which action resolves the issue? A. Change the R1 dead timer to 20. B. Change the R2 dead timer to 20. Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) C. Change the R2 hello timer to 20. D. Change the R1 hello timer to 20. Answer: A NEW QUESTION 209 - (Exam Topic 3) An engineer is implementing a coordinated change with a server team. As part of the change, the engineer must configure interlace GigabitEthernet2 in an existing VRF "RED" then move the interface to an existing VRF "BLUE" when the server team is ready. The engineer configured interface GigabitEthemet2 in VRF "RED" Which configuration completes the change? A. interface GigabitEthernet2 no ip addressvrf forwarding BLUE B. interface GigabitEthernet2 no vrf forwarding RED vrf forwarding BLUEip address 10.0.0.0 255.255.255.254 C. interface GigabitEthernet2 no vrf forwarding RED vrf forwarding BLUE D. interface GigabitEthernet2 no ip addressip address 10.0.0.0 255.255.255.254vrf forwarding BLUE Answer: B Explanation: When assigning an interface to a VRF, the IP address will be removed so we have to reassign the IP address to that interface. NEW QUESTION 212 - (Exam Topic 3) What action is performed for untagged outgoing labels in an MPLS router? A. Convert the incoming MPLS packet to an untagged packet and then do a FIB lookup B. Convert the incoming MPLS packet to an untagged packet and then do a RIB lookup. C. Convert the untagged packet to a labeled packet and forward it to the next router D. Convert the incoming MPLS packet to an IP packet and forward it to the next router. Answer: C NEW QUESTION 214 - (Exam Topic 3) A network administrator opens a telnet connection to the router and gets the message: R1#telnet 10.1.1.2 Trying 10 1.1 2 Open (Connection to 10.1.1.2 closed by foreign host) Router R2 is configured with enable secret and password commands. Which action resolves the issue? A. Configure the logging synchronous command on line vty. B. Configure the exec command on line vty. C. Configure the login local command on line vty D. Configure the enable password command on line vty. Answer: C NEW QUESTION 216 - (Exam Topic 3) Refer to the exhibit. The security department recently installed a monitoring device between routers R3 and R5, which a loss of network connectivity for users connected to R5. Troubleshooting revealed that the monitoring device cannot forward multicast packets. The team already updated R5 with the correct configuration. Which configuration must be implemented on R3 to resolve the problem by ensuring R3 as the DR for the R3-R5 segment? A) Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) B) C) D) Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) A. Option A B. Option B C. Option C D. Option D Answer: C NEW QUESTION 217 - (Exam Topic 3) A network is configured with CoPP to protect the CORE router route processor for stability and DDoS protection. As a company policy, a class named class-default is preconfigured and must not be modified or deleted. Troubleshoot CoPP to resolve the issues introduced during the maintenance window to ensure that: WAN Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) CORE Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) MGMT Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) A. Mastered B. Not Mastered Answer: A Explanation: CORE policy-mao CoPP class CoPP-CRITICAL police 1000000 50000 50000 conform-action transmit exceed-action transmit Text Description automatically generated with medium confidence CORE# Copy run start TESTING: CORE Graphical user interface Description automatically generated with medium confidence MGMT Graphical user interface, text Description automatically generated Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) NEW QUESTION 222 - (Exam Topic 3) An engineer creates a default static route on a router with a hop of 10.1.1.1. On inspection, the engineer finds the router has two VRFs, Red and Blue. The next hop is valid for both VRFs and exists in each assigned VRF. Which configuration achieves connectivity? A. Option A B. Option B C. Option C D. Option D Answer: A NEW QUESTION 223 - (Exam Topic 3) Refer to the exhibit. Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) AS111 is receiving its own routes from AS200 causing a loop in the network. Which configuration provides loop prevention? A) B) C) D) A. Option A B. Option B C. Option C D. Option D Answer: C Explanation: A router discards BGP network prefixes if it sees its ASN in AS-Path as a loop prevention mechanism. The “allowas-in” feature allows routes to be received and processed even if router detects its own ASN in AS-Path. NEW QUESTION 228 - (Exam Topic 3) Refer to the exhibit. TCP traffic should be reaching host 10.10.10.10/24 via R2. Which action resolves the issue? A. TCP traffic will reach the destination via R2 without any changes B. Add a permit 20 statement in the route map to allow TCP traffic C. Allow TCP in the access list with no changes to the route map D. Set IP next-hop to 10.10.12.2 under the route-map permit 10 to allow TCP traffic. Answer: C Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) NEW QUESTION 229 - (Exam Topic 3) Refer to the exhibit. An engineer must configure OSPF with R9 and R10 and configure redistribution between OSPF and RIP causing a routing loop Which configuration on R9 and R10 meets this objective? A) B) C) D) A. Option A B. Option B C. Option C D. Option D Answer: A Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) NEW QUESTION 234 - (Exam Topic 3) Refer to the exhibit. A customer finds that traffic from the application server (192.168.1.1) to the HUB site passes through a congested path that causes random packet drops. The NOC team influences the BGP path with MED on RB. but RD still sees that traffic coming from RA is not taking an alternate route. Which configuration resolves the issue? A) B) C) D) A. Option A B. Option B C. Option C D. Option D Answer: D NEW QUESTION 237 - (Exam Topic 3) Which protocol must be secured with MD-5 authentication across the MPLS cloud to prevent hackers from introducing bogus routers? A. MP-BGP Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) B. LSP C. RSVP D. LDP Answer: A NEW QUESTION 238 - (Exam Topic 3) A network administrator added a new spoke site with dynamic IP on the DMVPN network. Which configuration command passes traffic on the DMVPN tunnel from the spoke router? A. ip nhrp registration ignore B. ip nhrp registration no-registration C. ip nhrp registration dynamic D. ip nhrp registration no-unique Answer: D NEW QUESTION 240 - (Exam Topic 3) How is VPN routing information distributed in an MPLS network? A. The top level of the customer data packet directs it to the correct CE device B. It is established using VPN IPsec peers. C. It is controlled using of VPN target communities. D. It is controlled through the use of RD. Answer: C Explanation: The distribution of virtual private network (VPN) routing information is controlled through the use of VPN route target communities, implemented by Border Gateway Protocol (BGP) extended communities. Reference: https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/mp_l3_vpns/configuration/15-mt/mp-l3-vpns-15-mt-book/m NEW QUESTION 241 - (Exam Topic 3) Refer to the exhibit. An engineer is trying to log in to R1 via R3 loopback address. Which action resolves the issue? A. Add transport input SCP B. Add transport input none C. Remove the IPv6 traffic filter from R1, which is blocking the Telnet. D. Remove the IPv6 traffic from R1, which is blocking the SSH Answer: C NEW QUESTION 242 - (Exam Topic 3) Which function does LDP provide in an MPLS topology? A. It enables a MPLS topology to connect multiple VPNs to P routers. B. It provides hop-by-hop forwarding in an MPLS topology for LSRs. C. It exchanges routes for MPLS VPNs across different VRFs. D. It provides a means for LSRs to exchange IP routes. Answer: B Explanation: LDP provides a standard methodology for hop-by-hop, or dynamic label, distribution in an MPLS network by assigning labels to routes that have been chosen by the underlying Interior Gateway Protocol (IGP) routing protocols. The resulting labeled paths, called label switch paths (LSPs), forward label traffic across an MPLS backbone to particular destinations. Reference: https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/mp_ldp/configuration/12-4t/mp-ldp- 12-4t-book.pdf NEW QUESTION 245 - (Exam Topic 3) Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) Refer to the exhibit. An administrator can log in to the device using Telnet but the attempts to log in to the same device using SSH with the same credentials fail Which action resolves this issue? A. Configure SSH service on the router B. Configure transport input all on the VTY lines to allow SSH C. Configure to use the Telnet user database for SSH as well D. Configure the VTY lines with login local Answer: A NEW QUESTION 246 - (Exam Topic 3) Refer to the exhibits. Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) London must reach Rome using a faster path via EIGRP if all the links are up but it failed to take this path Which action resolves the issue? A. Increase the bandwidth of the link between London and Barcelona B. Use the network statement on London to inject the 172 16 X 0/24 networks into EIGRP. C. Change the administrative distance of RIP to 150 D. Use the network statement on Rome to inject the 172 16 X 0/24 networks into EIGRP Answer: D NEW QUESTION 250 - (Exam Topic 3) Which 0S1 model is used to insert an MPLS label? A. between Layer 5 and Layer 6 B. between Layer 1 and Layer 2 C. between Layer 3 and Layer 4 D. between Layer 2 and Layer 3 Answer: D NEW QUESTION 255 - (Exam Topic 3) An engineer configured routing between multiple OSPF domains and introduced a routing loop that caused network instability. Which action resolves the problem? A. Set a tag using the redistribute command toward a domain and deny inbound m the other domain by a matching tag B. Set a tag using the redistribute command toward a different domain and deny the matching tag when exiting from that domain C. Set a tag using the network command in a domain and use the route-map command to deny the matching lag when exiting toward a different domain D. Set a tag using the network command in a domain and use the route-map command to deny the matching tag when entering into a different domain Answer: A NEW QUESTION 257 - (Exam Topic 3) Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) Refer to the exhibit. An engineer applied filter on R1 The interface flapped between R1 and R2 and cleaning the BGP session did not restore the BGP session and failed Which action must the engineer take to restore the BGP session from R2 to R1? A. Apply the IPv6 traffic filter in the outbound direction on the interface B. ICMPv6 must be permitted by the IPv6 traffic filter C. Enable the BGP session, which went down when the session was cleared. D. Swap the source and destination IP addresses in the IPv6 traffic filter Answer: B NEW QUESTION 260 - (Exam Topic 3) Refer to the exhibit. An engineer noticed that the router log messages do not have any information about when the event occurred. Which action should the engineer take when Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) enabling service time stamps to improve the logging functionality at a granular level? A. Replace OSPF process 10 on the interfaces with OSPF process 1 and configure an additional router IO with IPv6 address B. Replace OSPF process 10 on the interfaces with OSPF process 1. and remove process 10 from the global configuration C. Replace OSPF process 10 on the interfaces with OSPF process 1 for the IPv6 address and remove process 10 from the global configuration D. Replace OSPF process 10 on the interfaces with OSPF process 1 for the IPv4 address and remove process 10 from the global configuration Answer: D NEW QUESTION 265 - (Exam Topic 3) Refer to the exhibit. An engineer must establish a point-to-point GRE VPN between R1 and the remote site. Which configuration accomplishes the task for the remote site? A. Interface Tunnel1 tunnel source 199.1.1.1tunnel destination 200.1.1.3ip address 192.168.1.3 255.255.255.0 B. Interface Tunnel1 tunnel source 200.1.1.3tunnel destination 199.1.1.1ip address 192.168.1.1.255.255.255.0 C. Interface Tunnel1 tunnel source 200.1.1.3tunnel destination 199.1.1.1ip address 192.168.1.3.255.255.255.0 D. Interface Tunnel lunnel source 199.1.1.1tunnel destination 200.1.1.3ip address 192.168.1.1.255.255.255.0 Answer: C NEW QUESTION 270 - (Exam Topic 3) What is a MPLS PHP label operation? A. Downstream node signals to remove the label. B. It improves P router performance by not performing multiple label lookup. C. It uses implicit-NULL for traffic congestion from source to destination forwarding D. PE removes the outer label before sending to the P router. Answer: A NEW QUESTION 273 - (Exam Topic 3) What is a characteristic of Layer 3 MPLS VPNs? A. LSP signaling requires the use of unnumbered IP links for traffic engineering. B. Traffic engineering supports multiple IGP instances C. Traffic engineering capabilities provide QoS and SLAs. D. Authentication is performed by using digital certificates or preshared keys. Answer: C Explanation: Reference: https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/mp_te_diffserv/configuration/15-mt/mp-te-diffserv-15-mt-bo MPLS traffic engineering supports only a single IGP process/instance The MPLS traffic engineering feature does not support routing and signaling of LSPs over unnumbered IP links. Reference: https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/mp_te_path_setup/configuration/xe- 3s/mp-te-path-setup-xe-3s-book/mp-te-enhance-xe.html NEW QUESTION 277 - (Exam Topic 3) Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) Refer to the exhibit Which command must be configured to make VRF CCNP work? A. Option A B. Option B C. Option C D. Option D Answer: B NEW QUESTION 279 - (Exam Topic 3) A company Is redesigning WAN infrastructure so that all branch sites must communicate via the head office and the head office can directly communicate with each site independently. The network engineer must configure the head office router by considering zero-touch technology when adding new sites in the same WAN infrastructure. Which configuration must be applied to the head office router to meet this requirement? A. Option A B. Option B C. Option C D. Option D Answer: D NEW QUESTION 281 - (Exam Topic 3) Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) Refer to the exhibit. An engineer configured router R3 to redistribute the prefix 10.10.10.0/24 from OSPF into EIGRP R1 has no connectivity to the prefix. Which action enables receipt of prefixes on R1? A. R3 is advertising the 10.20.20 0'24 prefix with a TTL of 1, R3 must set the TTL to 2 for this prefix. B. R1 docs not have a neighbor relationship with R2. The EIGRP process should be cleared on R1. C. Duplicate router IDs on R1 and R3, R1 should modify its router ID. D. R1 is not receiving the next-hop IP address of R3. R2 must enable the network 10 20.20.0V24 within EIGRP. Answer: B NEW QUESTION 282 - (Exam Topic 3) The network administrator configured the router for Control Plane Policing to limit OSPF traffic to be policed to 1 Mbps. Any traffic that exceeds this limit must also be allowed at this point for traffic analysis. The router configuration is: access-list 100 permit ospf any any ! class-map CM-OSPF match access-group 100 ! policy-map PM-COPP class CM-OSPF police 1000000 conform-action transmit ! control-plane service-policy output PM-COPP The Control Plane Policing failed to monitor and police OSPF traffic. Which configuration resolves this issue? A. Option A B. Option B C. Option C D. Option D Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) Answer: A NEW QUESTION 285 - (Exam Topic 3) A newly installed spoke router is configured for DMVPN with the ip mtu 1400 command. Which configuration allows the spoke to use fragmentation with the maximum negotiated TCP MTU over GRE? A. ip tcp adjust-mss 1360crypto ipsec fragmentation after-encryption B. ip tcp adjust-mtu 1360crypto ipsec fragmentation after-encryption C. ip tcp adjust-mss 1360crypto ipsec fragmentation mtu-discovery D. ip tcp adjust-mtu 1360crypto ipsec fragmentation mtu-discovery Answer: A Explanation: https://www.cisco.com/c/en/us/support/docs/security/dynamic-multipoint-vpn-dmvpn/111976-dmvpn-troublesh NEW QUESTION 288 - (Exam Topic 3) Refer to lhe exhibit After an engineer configured a new Cisco rouler as a DHCP server, users reponed iwo primary issues: Devices in the HR subnet have intermittent connectivity problems. Workstations in the LEGAL subnet cannot obtain IP addresses. Which configurations must the engineer apply to ROUTER_1 to restore connectivity for the affected devices? Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) A. Option A B. Option B C. Option C D. Option D Answer: A NEW QUESTION 293 - (Exam Topic 3) Refer to the exhibit. Which two commands provide the administrator with the information needed to resolve the issue? (Choose two.) A. Show snmp user B. debug snmp engine-id C. debug snmpv3 engine-id D. debug snmp packet E. showsnmpv3 user Answer: AD Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) Explanation: There are 3 values in the SNMPv3 header that must match for the communication to take place: snmpEngineID, snmpEngineTime, snmpEngineBoots. The error received indicates a problem with the EngineID value: “authentication failure, Unknown Engine ID” To specify the Engine ID, we can use the command “show snmp user”. The following example specifies the username as abcd with Engine ID: 00000009020000000C025808: The “debug snmp packet” command displays all SNMP packets that are arriving and being replied to. NEW QUESTION 294 - (Exam Topic 3) Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) Refer to the exhibit. Site1 must perform unequal cost load balancing toward the segments behind Site2 and Site3. Some of the routes are getting load balanced but others are not. Which configuration allows Site1 to load balance toward all the LAN segments of the remote routers? A. Option A B. Option B C. Option C D. Option D Answer: D NEW QUESTION 295 - (Exam Topic 3) Which technique removes the outermost label of an MPLS-tagged packet before the packet is forwarded to an adjacent LER? A. label swap B. explicit-null C. label imposition D. PHP Answer: D NEW QUESTION 299 - (Exam Topic 3) Refer to the exhibit. An engineer must configure PBR on R1 to reach to 10.2.2.0/24 via R3 AS64513 as the primary path and a backup route through default route via R2 AS64513. All BGP routes are in the routing table of R1. but a static default route overrides BGP routes. Which PBR configuration achieves the objective? Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) A. Option A B. Option B C. Option C D. Option D Answer: B NEW QUESTION 301 - (Exam Topic 3) Refer to the exhibit. R1 has a route map configured, which results in a loss of partial IPv6 prefixes for the BGP neighbor, resulting in service degradation. How can the full service be restored? A. The neighbor requires a soft reconfiguration, and this will clear the policy without resetting the BGP TCP connection. B. The prefix lit requires all prefixes that R1 is advertising to be added to it, and this will allow additional prefixes to be advertised. C. The route map requires a deny 20 statement without set conditions, and this will allow additional prefixes to be advertised. D. The route map requires a permit 20 statement without set conditions, and this will allow additional prefixes to be advertised. Answer: D NEW QUESTION 306 - (Exam Topic 3) Refer to the exhibit An engineer must connect the Reno and Detroit spokes using DMVPN phase 2 Hub tunnel configuration is Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) Which configuration accomplishes the task? Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) A. Option A B. Option B C. Option C D. Option D Answer: C NEW QUESTION 308 - (Exam Topic 3) A network administrator cannot connect to a device via SSH. The line vty configuration is as follows: Which action resolves this issue? A. Increase the session timeout B. Change the stopbits to 10. C. Configure the transport input SSH D. initialize the SSH key Answer: D NEW QUESTION 311 - (Exam Topic 3) Refer to the exhibit. An engineer notices a connectivity problem between routers R1 and R2. The frequency of this problem is high during peak business hours. Which action resolves the issue? A. Increase the MTU on the interfaces that connect R1 and R2. B. Increase the available bandwidth between R1 and R2. C. Decrease the EIGRP keepallve and hold down timers on R1 and R2. D. Set static EIGRP neighborship between R1 and R2. Answer: B Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) NEW QUESTION 315 - (Exam Topic 3) The network administrator configured CoPP so that all routing protocol traffic toward the router CPU is limited to 1 mbps. All traffic that exceeds this limit must be dropped. The router is running BGP and OSPF Management traffic for Telnet and SSH must be limited to 500kbps. access-list 100 permit tcp any any eq 179 access-list 100 permit tcp any any range 22 23 access-list 100 permit ospf any any ! class-map CM-ROUTING match access-group 100 class-map CM-MGMT match access-group 100 ! policy-map PM-COPP class CM-ROUTING police 1000000 conform-action transmit class CM-MGMT police 500000 conform-action transmit ! control-plane service-policy output PM-COPP No traffic is filtering through CoPP,which is resulting in high CPU utilization,which configuration resolves the issue ? A. no access-list 100access-list 100 permit tcp any any eq 179 access-list 100 permit ospf any anyaccess-list 101 Permit tcp any any range 22 23!class-map CM- MGMTno match access-group 100 match access-group 101 B. control-planeno service-policy output PM-COPP service-policy input PM-COPP C. No access-list 100access-list 100 permit tcp any any eq 179access-list 100 permit tcp any any range eq 22 access-list 100 permit tcp any any range eq 23 access-list 100 permit ospf any any D. no access-list 100access-list 100 permit tcp any any eq 179 access-list 100 permit ospf any anyaccess-list 101 Permit tcp any any range 22 23!class-map CM- MGMTno match access-group 100 match access-group 101!control-planeno service-policy output PM-COPP service-policy input PM-COPP Answer: D NEW QUESTION 319 - (Exam Topic 3) Refer to the exhibit. Router R1 peers with two ISPs using static routes to get to the internet. The requirement is that R1 must prefer ISP-A under normal circumstances and failover to ISP-B if the connectivity to ISP-A is lost. The engineer observes that R1 is load balancing traffic across the two ISPs Which action resolves the issue by sending traffic to ISP-A only with failover to ISP-B? A. Configure OSPF between R1. ISP- B. and ISP-B for dynamic failover if any ISP link to R1 fails C. Configure two static routes on R1. one pointing to ISP-A and another pointing to ISP- B with 222 admin distance D. Change the bandwidth of the interface on R1 so that interface to ISP-A has a higher value than the interface to ISP-B E. Configure two static routes on R1. one pointing to ISP-B with more specific routes and another pointing to ISP-A with summary routes Answer: D NEW QUESTION 322 - (Exam Topic 3) What does the MP-BGP OPEN message contain? A. MPLS labels and the IP address of the router that receives the message B. the version number and the AS number to which the router belongs C. IP routing information and the AS number to which the router belongs D. NLRI, path attributes, and IP addresses of the sending and receiving routers Answer: B NEW QUESTION 324 - (Exam Topic 3) Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) Refer to the exhibit. An administrator must harden a router, but the administrator failed to test the SSH access successfully to the router. Which action resolves the issue? A. Configure SSH on the remote device to log m using SSH B. SSH syntax must be ssh -I user ip to log in to the remote device C. Configure enable secret to log in to the device D. SSH must be allowed with the transport output ssh command Answer: B NEW QUESTION 326 - (Exam Topic 3) Refer to the exhibit. The administrator noticed that the connection was flapping between the two ISPs instead of switching to ISP2 when the ISP1 failed. Which action resolves the issue? A. Include a valid source-interface keyword in the icmp-echo statement. B. Reference the track object 1 on the default route through ISP2 instead of ISP1. C. Modify the static routes to refer both to the next hop and the outgoing intertace. D. Modify the threshold to match the administrative distance of the ISP2 route. Answer: A Explanation: https://www.cisco.com/c/en/us/support/docs/ip/ip-routing/200785-ISP-Failover-withdefault- routes-using-I.html NEW QUESTION 329 - (Exam Topic 3) Refer to the exhibit. Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) The static route is not present in the routing table of an adjacent OSPF neighbor router. Which action resolves the issue? A. Configure the next hop of 10.20.20.1 in the prefix list DMZ-STATIC B. Configure the next-hop interface at the end of the static router for it to get redistributed C. Configure a permit 20 statement to the route map to redistribute the static route D. Configure the subnets keyword in the redistribution command Answer: D NEW QUESTION 332 - (Exam Topic 3) Refer to the exhibit. A network engineer finds that PC1 is accessing the hotel website to do the booking but fails to make payment. Which action resolves the issue? A. Allow stub network 10.10.202.168/30 on router R3 OSPF. B. Decrease the AD to 5 OSPF route 192.168.94.0 on R1. C. Increase the AD to 200 of static route 192.168.94.0 on R3. D. Configure a reverse route on R1 for PC1 172.16.1.0/24. Answer: A NEW QUESTION 333 - (Exam Topic 3) A network administrator is troubleshooting a high utilization issue on the route processor of a router that was reported by NMS The administrator logged into the router to check the control plane policing and observed that the BGP process is dropping a high number of routing packets and causing thousands of routes to recalculate frequently. Which solution resolves this issue? A. Police the cir for BGP, conform-action transmit, and exceed action transmit. B. Shape the pir for BGP, conform-action set-prec-transmit, and exceed action set-frde-transmit. C. Shape the cir for BG D. conform-action transmit, and exceed action transmit. E. Police the pir for BGP, conform-action set-prec-transmit, and exceed action set-clp-transmit. Answer: D Explanation: CIR (Committed Information Rate) is the minimum guaranteed traffic delivered in the network. Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) PIR (Peak Information Rate) is the top bandwidth point of allowed traffic in a non busy times without any guarantee. + Policing: is used to control the rate of traffic flowing across an interface. During a bandwidth exceed (crossed the maximum configured rate), the excess traffic is generally dropped or remarked. The result of traffic policing is an output rate that appears as a saw-tooth with crests and troughs. Traffic policing can be applied to inbound and outbound interfaces. Unlike traffic shaping, QoS policing avoids delays due to queuing. Policing is configured in bytes. + Shaping: retains excess packets in a queue and then schedules the excess for later transmission over increments of time. When traffic reaches the maximum configured rate, additional packets are queued instead of being dropped to proceed later. Traffic shaping is applicable only on outbound interfaces as buffering and queuing happens only on outbound interfaces. Shaping is configured in bits per second. Therefore in this case we can only policing, not shaping as traffic shaping is applicable only on outbound interfaces as buffering and queuing happens only on outbound interfaces. Moreover, BGP traffic is not important so we can drop the excess packets without any problems. And we only policing the PIR traffic so that the route processor is not overwhelmed by BGP calculation. Note: The “set-prec-transmit” is the same as “transmit” command except it sets the IP Precedence level as well. The “set-clp-transmit” sets the ATM Cell Loss Priority (CLP) bit from 0 to 1 on the ATM cell and transmits the packet. NEW QUESTION 337 - (Exam Topic 3) Refer to the exhibit. An engineer is trying to add an encrypted user password that should not be visible in the router configuration. Which two configuration commands resolve the issue? (Choose two) A. password encryption aes B. username Admin password Cisco@maedeh motamedi C. username Admin password 5 Cisco@maedeh motamedi D. username Admin secret Cisco@maedeh motamedi E. no service password-encryption F. service password-encryption Answer: DF NEW QUESTION 340 - (Exam Topic 3) Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) The network administrator configured the router for Control Plane Policrg so that inbound SSH traffic is policed to 500 kbps This policy must apply to traffic coming in from 101010 0<24 and 192 168 10.0/24 networks The Control Rane Policing is not applied to SSH traffic and SSH is open to use any bandwidth available. Which configuration resolves this issue? A) B) C) D) A. Option B. Option C. Option Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) D. Option Answer: C NEW QUESTION 345 - (Exam Topic 3) Refer to the exhibit. A network engineer receives a fault ticket about traffic drops from BANK SITE to BANK Users can reach BANK SITE Y from router RA as a source. Routers RB and RD are acting as route reflectors. Which configuration resolves the issue? A. RC(config)#router bgp 65201RC(config-router)#neighbor 10.10.10.4 route-reflector-client B. RF(config)#router bgp 65201RF(config-router)#neighbor 10.10.10.6 route-reflector-client C. RC(config)#router bgp 65201RC(config-router)#neighbor 10.10.10.2 route-reflector-client D. RB(config)router bgp 65201RB(config-router)#neighbor 10.10.10.3 route-reflector-client Answer: A NEW QUESTION 350 - (Exam Topic 3) An engineer creates a Cisco DNA Center cluster with three nodes, but all the services are running on one host node. Which action resolves this issue? A. Restore the link on the switch interface that is connected to a cluster link on the Cisco DNA Center B. Click the master host node with all the services and select services to be moved to other hosts C. Enable service distribution from the Systems 360 page. D. Click system updates, and upgrade to the latest version of Cisco DNA Center. Answer: C Explanation: To deploy Cisco DNA Center on a three-node cluster with High Availability (HA) enabled, complete the following procedure: Step 1: Configure Cisco DNA Center on the first node in your cluster… Step 2: Configure Cisco DNA Center on the second node in your cluster… Step 3: Configure Cisco DNA Center on the third node in your cluster… Step 4: Enable high availability on your cluster: * a. In the Cisco DNA Center GUI, click and choose System Settings. The System 360 tab is displayed by default. * b. In the Hosts area, click Enable Service Distribution. After you click Enable Service Distribution, Cisco DNA Center enters into maintenance mode. In this mode, Cisco DNA Center is unavailable until the redistribution of services is completed. You should take this into account when scheduling an HA deployment. Reference: https://www.cisco.com/c/en/us/td/docs/cloud-systems-management/network-automationand- management/dna- center/1-3-3-0/ha_guide/b_cisco_dna_center_ha_guide_1_3_3_0.html Therefore we can choose “Enable Service Distribution” to distribute services to other host nodes. NEW QUESTION 355 - (Exam Topic 3) What is an MPLS LDP targeted session? A. session between neighbors that are connected no more than one hop away B. LDP session established between LSRs by exchanging TCP hello packets C. label distribution session between non-directly connected neighbors D. LDP session established by exchanging multicast hello packets Answer: C NEW QUESTION 360 - (Exam Topic 3) Refer to the exhibit. Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) A network administrator configured name resolution for IPv6 traffic to be allowed through an inbound access list. After the access list is applied to resolve the issue, name resolution still did not work. Which action does the network administrator take to resolve the name resolution problem? A. Remove ipv6 inspect ipv6-firewall in from interface gi0/1 B. Add permit udp any eq domain any log in the access list. C. inspect ipv6 inspect name ipv6-firewall udp 53 in global config. D. Add permit any eq domain 53 any log in the access list. Answer: A NEW QUESTION 362 - (Exam Topic 3) A. access-list 20 permit 10.221.10.12 B. snmp-server group NETVIEW v2c priv read NETVIEW access 20 C. snmp-server group NETADMIN v3 priv read NETVIEW write NETADMIN access 22 D. access-list 20 permit 10.221.10.11 Answer: D NEW QUESTION 367 - (Exam Topic 3) What is the purpose of the DHCPv6 Guard? A. It messages between a DHCPv6 server and a DHCPv6 client ( or relay agent). B. It shows that clients of a DHCPv5 server are affected. C. It block DHCPv6 messages from relay agents to a DHCPv6 server. D. It allows DHCPv6 replay and advertisements from (rouge) DHCPv6 servers. Answer: A Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) Explanation: https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/ipv6_fhsec/configuration/xe-16/ip6fxe- 16-book/ip6-dhcpv6-guard.html NEW QUESTION 372 - (Exam Topic 3) Configure individual VRFs for each customer according to the topology to achieve these goals : R1 Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) R2 Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) SW1 Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) SW2 Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) SW3 Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) A. Mastered B. Not Mastered Answer: A Explanation: Solution: Use cu-red under interfaces facing SW1 & SW3: On R1: interface Ethernet0/0 ip vrf forwarding cu-red ip address 192.168.1.254 255.255.255.0 Check reachability to SW1: R1#ping vrf cu-red 192.168.1.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.2.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms On R2: interface Ethernet0/0 ip vrf forwarding cu-red ip address 192.168.2.254 255.255.255.0 Check reachability to SW3: R2#ping vrf cu-red 192.168.2.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.1.1, timeout is 2 seconds: !!!!! Use vrf cu-green for SW2 & SW4: On R1: interface Ethernet0/1 ip vrf forwarding cu-green Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) ip address 192.168.20.254 255.255.255.0 Test reachability to SW2: R1#ping vrf cu-green 192.168.20.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.22.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms On R2: interface Ethernet0/1 ip vrf forwarding cu-green ip address 192.168.22.254 255.255.255.0 Test reachability to SW4: R2#ping vrf cu-green 192.168.22.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.20.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms On R1: interface Ethernet0/2.100 mpls ip ! interface Ethernet0/2.200 mpls ip ! Configure BGP: router bgp 65000 neighbor 10.10.10.2 remote-as 65000 neighbor 10.10.20.2 remote-as 65000 ! address-family vpnv4 neighbor 10.10.10.2 activate neighbor 10.10.20.2 activate exit-address-family ! address-family ipv4 vrf cu-green redistribute connected exit-address-family ! address-family ipv4 vrf cu-red redistribute connected exit-address-family ! R1(config)#ip vrf cu-red R1(config-vrf)#route-target both 65000:100 ! R1(config)#ip vrf cu-green R1(config-vrf)#route-target both 65000:200 On R2: interface Ethernet0/2.100 mpls ip ! interface Ethernet0/2.200 mpls ip ! router bgp 65000 neighbor 10.10.10.1 remote-as 65000 neighbor 10.10.20.1 remote-as 65000 ! address-family vpnv4 neighbor 10.10.10.1 activate neighbor 10.10.20.1 activate exit-address-family ! address-family ipv4 vrf cu-green redistribute connected exit-address-family ! address-family ipv4 vrf cu-red redistribute connected exit-address-family R2(config)#ip vrf cu-red R2(config-vrf)#route-target both 65000:100 ! R2(config)#ip vrf cu-green R2(config-vrf)#route-target both 65000:200 Verification: From SW1 to SW3: SW1#ping 192.168.1.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.1.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms But can’t Reach SW2 or SW4 in VRF cu-green: SW1#ping 192.168.22.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.22.1, timeout is 2 seconds: U.U.U Success rate is 0 percent (0/5) SW1#ping 192.168.20.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.20.1, timeout is 2 seconds: U.U.U Success rate is 0 percent (0/5) Same Test for SW2: From SW2 to SW4: SW2#ping 192.168.20.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.20.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms But can’t Reach SW3 or SW1 in VRF cu-red: SW2#ping 192.168.1.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.1.1, timeout is 2 seconds: U.U.U Success rate is 0 percent (0/5) Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) SW2#ping 192.168.2.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.2.1, timeout is 2 seconds: U.U.U Success rate is 0 percent (0/5) Both R1 & R2 has separate tables for VRFs cu-red and cu-green. NEW QUESTION 374 - (Exam Topic 3) Refer to the exhibit. The default route is not advertised to the neighboring router. Which action resolves the issue? A. Configure the redistribute static metric 200 subnets command under OSPF. B. Configure OSPF on the Dialer0 interface. C. Configure the network 0.0.0.0 255.255.255.255 area 0 command under OSPF. D. Configure the default-information originate command under OSPF. Answer: D NEW QUESTION 377 - (Exam Topic 3) Refer to the exhibit. An engineer must configure EIGRP between R1 and R2 with no summary route. Which configuration resolves the issue? A) B) Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) C) D) A. Option A B. Option B C. Option C D. Option D Answer: B NEW QUESTION 380 - (Exam Topic 3) Refer to the exhibit. Which policy configuration on R1 forwards any traffic that is sourced from the 192 168 130 0'24 network to R2? A) B) C) D) Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) A. Option A B. Option B C. Option C D. Option D Answer: B NEW QUESTION 383 - (Exam Topic 3) Refer to the exhibit. A prefix list is created to filter routes inbound to an EIGRP process except for network 10 prefixes After the prefix list is applied no network 10 prefixes are visible in the routing table from EIGRP. Which configuration resolves the issue? A. ip prefix-list EIGRP seq 20 permit 10.0.0.0/8 ge 9. B. ip prefix-list EIGRP seq 10 permit 0.0.0.0/0 le 32 C. ip prefix-list EIGRP seq 5 permit 10.0.0.0/8 ge 9 no ip prefix-list EIGRP seq 20 permit 10.0.0.0/8 D. ip prefix-list EIGRP seq 20 permit 10.0.0.0/8 ge 9 ip prefix-list EIGRP seq 10 permit 0.0.0.0/0 le 32 Answer: C NEW QUESTION 388 - (Exam Topic 2) Refer to the exhibit. Which action resolves the adjacency issue? A. Match the hello interval timers. B. Configure the same EIGRP process IDs. C. Match the authentication keys. D. Configure the same autonomous system numbers. Answer: D Explanation: EIGRP does not have process ID as it uses Autonomous System (AS) numbers only. This is not an authentication problem or we would see this error from the debug: EIGRP: Ethernet0/0: ignored packet from 10.1.1.3, opcode = 1 (missing authentication or key-chain missing) If the AS numbers between two routers are different then the neighbor relationship cannot be formed. Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) NEW QUESTION 391 - (Exam Topic 3) Refer to the exhibit. A customer reports that networks in the 10.0.1.0/24 space do not appear in the RIP database. What action resolves the issue? A. Remove summarization of 10.0.0.078. B. Permit 10.0.1.0/24 address in the ACL. C. Remove ACL on R1 blocking 10.0.1.0/24 network. D. Configure 10.0.1.0/24 network under RIP. Answer: A NEW QUESTION 394 - (Exam Topic 3) A customer is running an mGRE DMVPN tunnel over WAN infrastructure between hub and spoke sites. The existing configuration allows NHRP to add spoke routers automatically to the multicast NHRP mappings. The customer is migrated the network from IPv4 to the IPv6 addressing scheme for those spokes’ routers that support IPv6 and can run DMVPN tunnel over the IPv6 network. Which configuration must be applied to support IPv4 and IPv6 DMVPN tunnel on spoke routers? A. Tunnel mode ipv6ip 6to4 B. Tunnel mode ipv6ip isatap C. Tunnel mode ipv6ip auto-tunnel D. Tunnel mode ipv6ip 6rd Answer: C NEW QUESTION 398 - (Exam Topic 2) Refer to the exhibit. The administrator configured route advertisement to a remote low resources router to use only the default route to reach any network but failed. Which action resolves this issue? A. Change the direction of the distribute-list command from out to in. B. Remove the line with the sequence number 5 from the prefix list. C. Remove the prefix keyword from the distribute-list command. D. Remove the line with the sequence number 10 from the prefix list. Answer: B NEW QUESTION 403 - (Exam Topic 2) Refer to the exhibit. Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) An IT staff member comes into the office during normal office hours and cannot access devices through SSH Which action should be taken to resolve this issue? A. Modify the access list to use the correct IP address. B. Configure the correct time range. C. Modify the access list to correct the subnet mask D. Configure the access list in the outbound direction. Answer: A Explanation: To ACL should be permit tcp 101 10.1.1.1 0.0.0.0 NEW QUESTION 404 - (Exam Topic 2) Drag and drop the MPLS concepts from the left onto the descriptions on the right. A. Mastered B. Not Mastered Answer: A Explanation: A label edge router (LER, also known as edge LSR) is a router that operates at the edge of an MPLS network and acts as the entry and exit points for the network. LERspush an MPLS label onto an incoming packet and pop it off an outgoing packet. A forwarding equivalence class (FEC) is a term NEW QUESTION 405 - (Exam Topic 2) Refer to the exhibit. A network administrator redistributed the default static route into OSPF toward all internal routers to reach to Internet. Which set of commands restores reachability to the Internet by internal routers? A. router ospf 1default-information originate B. router ospf 1network 0.0.0.0 0.0.0.0 area 0 C. router ospf 1redistribute connected 0.0.0.0 D. router ospf 1redistribute static subnets Answer: A NEW QUESTION 406 Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) - (Exam Topic 2) Refer to the exhibit. A user has set up an IP SLA probe to test if a non-SLA host web server on IP address 10.1.1.1 accepts HTTP sessions prior to deployment. The probe is failing. Which action should the network administrator recommend for the probe to succeed? A. Re-issue the ip sla schedule command. B. Add icmp-echo command for the host. C. Add the control disable option to the tcp connect. D. Modify the ip sla schedule frequency to forever. Answer: C NEW QUESTION 409 - (Exam Topic 2) Refer to the exhibit. A client is concerned that passwords are visible when running this show archive log config all. Which router configuration is needed to resolve this issue? A. MASS-RTR(config-archive-log-cfg)#password encryption aes B. MASS-RTR(config)#aaa authentication arap Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) C. MASS-RTR(config)#service password-encryption D. MASS-RTR(config-archive-log-cfg)#hidekeys Answer: D Explanation: NEW QUESTION 411 - (Exam Topic 2) Refer to the exhibit. The OSPF routing protocol is redistributed into the BGP routing protocol, but not all the OSPF routes are distributed into BGP Which action resolves the issue? A. Include the word external in the redistribute command B. Use a route-map command to redistribute OSPF external routes defined in an access list C. Include the word internal external in the redistribute command D. Use a route-map command to redistribute OSPF external routes defined in a prefix list. Answer: C Explanation: If you configure the redistribution of OSPF into BGP without keywords, only OSPF intra-area and inter-area routes are redistributed into BGP, by default. You can use the internal keyword along with the redistribute command under router bgp to redistribute OSPF intra- and inter-area routes. Use the external keyword along with the redistribute command under router bgp to redistribute OSPF external routes into BGP. -> In order to redistribute all OSPF routes into BGP, we must use both internal and external keywords. The full command would be (suppose we are using OSPF 1): redistribute ospf 1 match internal external Note: The configuration shows match internal external 1 external 2. This is normal because OSPF automatically appends “external 1 external 2” in the configuration. In other words, keyword external = external 1 external 2. External 1 = O E1 and External 2 = O E2. Reference: https://www.cisco.com/c/en/us/support/docs/ip/border-gateway-protocol-bgp/5242-bgp-ospf-redi s.html NEW QUESTION 413 - (Exam Topic 2) Refer to the exhibit. When monitoring an IPv6 access list, an engineer notices that the ACL does not have any hits and is causing unnecessary traffic to pass through the interface Which command must be configured to resolve the issue? A. access-class INTERNET in Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) B. ipv6 traffic-filter INTERNET in C. ipv6 access-class INTERNET in D. ip access-group INTERNET in Answer: C NEW QUESTION 417 - (Exam Topic 2) Refer to the exhibit. The network administrator configured redistribution on an ASBR to reach to all WAN networks but failed Which action resolves the issue? A. The route map must have the keyword prefix-list to evaluate the prefix list entries B. The OSPF process must have a metric when redistributing prefixes from EIGRP. C. The route map EIGRP->OSPF must have the 10.0.106.0/24 entry to exist in one of the three prefix lists to pass D. EIGRP must redistribute the 10.0.106.0/24 route instead of using the network statement Answer: A Explanation: In order to use a prefix-list in a route-map, we must use the keyword “prefix-list” in the “match” statement. . For example: match ip address prefix-list WAN_PREFIXES Without this keyword, the router will try to find an access-list with the same name instead. NEW QUESTION 421 - (Exam Topic 2) Refer to the exhibit. SanFrancisco and Boston routers are choosing slower links to reach each other despite the direct links being up Which configuration fixes the issue? Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) A. Option A B. Option B C. Option C D. Option D Answer: D NEW QUESTION 426 - (Exam Topic 2) When configuring Control Plane Policing on a router to protect it from malicious traffic, an engineer observes that the configured routing protocols start flapping on that device. Which action in the Control Plane Policy prevents this problem in a production environment while achieving the security objective? A. Set the conform-action and exceed-action to transmit initially to test the ACLs and transmit rates and apply the Control Plane Policy in the output direction B. Set the conform-action and exceed-action to transmit initially to test the ACLs and transmit rates and apply the Control Plane Policy in the input direction C. Set the conform-action to transmit and exceed-action to drop to test the ACLs and transmit rates and apply the Control Plane Policy m the input direction D. Set the conform-action to transmit and exceed-action to drop to test the ACLs and transmit rates and apply the Control Plane Policy m the output direction Answer: B NEW QUESTION 429 - (Exam Topic 2) Refer to the exhibit. Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) All the serial between R1, R2, and R3 have the Same bandwidth. User on the 192.168.1.0/24 network report slow response times while they access resource on network 192.168.3.0/24. When a traceroute is run on the path. It shows that the packet is getting forwarded via R2 to R3 although the link between R1 and R3 is still up. What must the network administrator to fix the slowness? A. Change the Administrative Distance of EIGRP to 5. B. Add a static route on R1 using the next hop of R3. C. Remove the static route on R1. D. Redistribute theR1 route to EIGRP Answer: C NEW QUESTION 432 - (Exam Topic 2) Exhibit: Which action resolves the authentication problem? A. Configure the user name on the TACACS+ server B. Configure the UDP port 1812 to be allowed on the TACACS+ server C. Configure the TCP port 49 to be reachable by the router D. Configure the same password between the TACACS+ server and router. Answer: D Explanation: From the last line of the output, we notice that the result was “Invalid AUTHEN packet”. Therefore something went wrong with the username or password. Reference: https://www.cisco.com/c/en/us/support/docs/security-vpn/terminal-access-controller-access-control-system-taca NEW QUESTION 434 - (Exam Topic 2) Drag and drop the MPLS VPN device types from the left onto the definitions on the right. Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) A. Mastered B. Not Mastered Answer: A Explanation: Graphical user interface, application Description automatically generated NEW QUESTION 435 - (Exam Topic 2) Refer to the exhibit. An engineer wanted to set a tag of 30 to route 10 1.80.65/32 but it failed How is the issue fixed? A. Modify route-map ospf-to-eigrp permit 30 and match prefix-list ccnp2. B. Modify route-map ospf-to-eigrp permit 10 and match prefix-list ccnp2. C. Modify prefix-list ccnp3 to add 10.1.64.0/20 le 24 D. Modify prefix-list ccnp3 to add 10.1.64.0/20 ge 32 Answer: B NEW QUESTION 436 - (Exam Topic 2) Refer to the exhibit. Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) An engineer receives this error message when trying to access another router in-band from the serial interface connected to the console of R1. Which configuration is needed on R1 to resolve this issue? A. Option A B. Option B C. Option C D. Option D Answer: D Explanation: https://community.cisco.com/t5/other-network-architecture/out-of-band-router-access/td-p/333295 The “transport output none” command prevents any protocol connection made from R1. Therefore our SSH connection to 192.168.12.2 was refused. In order to fix this problem we can configure “transport output ssh” under “line console 0” of R1. Note: The parameter “-l” specifies the username to log in as on the remote machine. NEW QUESTION 439 - (Exam Topic 2) Refer to the exhibit. Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) Which two actions should be taken to access the server? (Choose two.) A. Modify the access list to add a second line of permit ip any B. Modify the access list to deny the route to 192.168.2.2. C. Modify distribute list seq 10 to permit the route to 192.168.2.2. D. Add a sequence 20 in the route map to permit access list 1. E. Add a floating static route to reach to 192.168.2.2 with administrative distance higher than OSPF Answer: BE NEW QUESTION 444 - (Exam Topic 2) Refer to the exhibit. A network administrator reviews the branch router console log to troubleshoot the OSPF adjacency issue with the DR router. Which action resolves this issue? A. Advertise the branch WAN interface matching subnet for the DR site. B. Configure matching hello and dead intervals between sites. C. Configure the WAN interface for DR site in the related OSPF area. D. Stabilize the DR site flapping link to establish OSPF adjacency. Answer: A NEW QUESTION 447 - (Exam Topic 2) Refer to the exhibit. Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) Which action resolves the failed authentication attempt to the router? A. Configure aaa authorization login command on line vty 0 4 B. Configure aaa authorization login command on line console 0 C. Configure aaa authorization console global command D. Configure aaa authorization console command on line vty 0 4 Answer: C Explanation: In the debug output, we see that the Authorization (not Authentication) failed so we need to correct the authorization. In order to enable authorization, we must use the global command “aaa authorization console” first. Reference: https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/security/a1/sec-a1-cr-book/sec-cr-a1.html NEW QUESTION 452 - (Exam Topic 2) What is the minimum time gap required by the local system before putting a BFD control packet on the wire? A. Detect Mult B. Required Min Echo RX Interval C. Desired Min TX Interval D. Required Min RX Interval Answer: C Explanation: Desired Min TX Interval: This is the minimum interval, in microseconds, that the local system would like to use when transmitting BFD Control packets, less any jitterapplied. The value zero is reserved. Required Min Echo RX Interval: This is the minimum interval, in microseconds, between received BFD Echo packets that this system is capable of supporting, less anyjitter applied by the sender. If this value is zero, the transmitting system does not support the receipt of BFD Echo packets. Reference: https://tools.ietf.org/html/rfc5880 NEW QUESTION 453 - (Exam Topic 2) Refer to Exhibit. Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) Which two configurations allow clients to get dynamic ip addresses assigned? A. Configure access-list 100 permit udp any any eq 61 as the first line B. Configure access-list 100 permit udp any any eq 86 as the first line C. Configure access-list 100 permit udp any any eq 68 as the first line D. Configure access-list 100 permit udp any any eq 69 as the first line E. Configure access-list 100 permit udp any any eq 67 as the first line Answer: CE Explanation: A DHCP server that receives a DHCPDISCOVER message may respond with a DHCPOFFER message on UDP port 68 (BootP client). … In the event that the DHCP server is not on the local subnet, the DHCP server will send the DHCPOFFER, as a unicast packet, on UDP port 67, back to the DHCP/BootPRelay Agent from which the DHCPDISCOVER came. Reference: https://www.cisco.com/c/en/us/support/docs/ip/dynamic-address-allocation-resolution/27470-100.html NEW QUESTION 457 - (Exam Topic 2) Refer to the exhibit. The engineer configured and connected Router2 to Router1. The link came up but could not establish a Telnet connection to Router1 IPv6 address of 2001:DB8::1. Which configuration allows Router2 to establish a Telnet connection to Router1? A. jpv6 unicast-routing B. permit ICMPv6 on access list INGRESS for Router2 to obtain IPv6 address C. permit ip any any on access list EGRESS2 on Router1 D. IPv6 address on GigabitEthernet0/0 Answer: D Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) Explanation: --------------------------R1-------------------------------------------- interface Ethernet0/0 ip address 209.165.201.1 255.255.255.0 ip access-group EGRESS2 out ipv6 address 2001:DB8::1/64 end ----------------------R2------------------------------------------------- interface Ethernet0/0 ip address 209.165.201.25 255.255.255.0 ipv6 address 2001:DB8::2/64 ipv6 address autoconfig ipv6 nd autoconfig default-route ipv6 nd cache expire 60 ipv6 nd ra suppress ipv6 traffic-filter INGRESS in end IOU_Router2#telnet 2001:DB8::1 Trying 2001:DB8::1 ... Open IOU_Router1> ----------------------------------------------------------------------------- NEW QUESTION 458 ...... Your Partner of IT Exam visit - https://www.exambible.com

We recommend you to try the PREMIUM 300-410 Dumps From Exambible https://www.exambible.com/300-410-exam/ (530 Q&As) Relate Links 100% Pass Your 300-410 Exam with Exambible Prep Materials https://www.exambible.com/300-410-exam/ Contact us We are proud of our high-quality customer service, which serves you around the clock 24/7. Viste - https://www.exambible.com/ Powered by TCPDF (www.tcpdf.org) Your Partner of IT Exam visit - https://www.exambible.com