Fox and McDonald's Introduction to Fluid Mechanics
9th Edition
ISBN: 9781118912652
Author: Philip J. Pritchard, John W. Mitchell
Publisher: WILEY
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 9, Problem 31P
Assume laminar boundary-layer flow to estimate the drag on the flat plate shown when it is placed parallel to a 15 ft/s air flow. The air is at 70°F and 1 atm.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
a smooth flat plate of length 5 m and width 2 m is moving with a velocity of 4 m/s in stationary air of density as 1.25 kg/m³ and kinematic viscosity 1.5 x 10-5 m²/s. determine thickness of the boundary layer at the trailing edge of the smooth plate. find the total drag on one side of the plate assuming that the boundary layer is turbulent from the very beginning.
A square flat plate with sides of length L 2m and a negligible
thickness (out of the page) is held stationary in a stream of air that
is moving steadily at standard conditions past the plate with a speed
U = 10 m/s that is uniform except for the boundary layers. Assume the
plate is oriented so that only friction drag is important. Determine the
drag coefficient for this plate.
Answer: CD, ≈ 0.003
=
U
L-
The drag polar equation of a light aircraft in clean configuration is:
CD=0.020+0.044C₁2. The aircraft has a wing area of 162.7 ft² and a
wing loading of 15.2 psf. It is flying at a velocity of 213 feet per second.
Assuming steady level flight and SSLC (p=0.002377 slug/ft³), determine
the drag force (in lb, nearest hundredths) being generated by the
aircraft.
Chapter 9 Solutions
Fox and McDonald's Introduction to Fluid Mechanics
Ch. 9 - The roof of a minivan is approximated as a...Ch. 9 - A model of a river towboat is to be tested at 1:18...Ch. 9 - For flow over a smooth plate, what approximately...Ch. 9 - A model of a thin streamlined body is placed in a...Ch. 9 - A student is to design an experiment involving...Ch. 9 - A 1 m 2 m sheet of plywood is attached to the...Ch. 9 - The extent of the laminar boundary layer on the...Ch. 9 - Velocity profiles in laminar boundary layers often...Ch. 9 - An approximation for the velocity profile in a...Ch. 9 - Evaluate / for each of the laminar boundary-layer...
Ch. 9 - Evaluate the displacement thickness and the...Ch. 9 - Evaluate the displacement thickness and the...Ch. 9 - A fluid, with density = 1.5 slug/ft3, flows at U...Ch. 9 - Solve Problem 9.13 with the velocity profile at...Ch. 9 - Air flows in a horizontal cylindrical duct of...Ch. 9 - Evaluate the displacement thickness and the...Ch. 9 - Evaluate the displacement thickness and the...Ch. 9 - A laboratory wind tunnel has a test section 25 cm...Ch. 9 - Air flows in the entrance region of a square duct,...Ch. 9 - A flow of 68F air develops in a flat horizontal...Ch. 9 - A flow of air develops in a horizontal cylindrical...Ch. 9 - Using numerical results for the Blasius exact...Ch. 9 - Using numerical results obtained by Blasius (Table...Ch. 9 - Using numerical results obtained by Blasius (Table...Ch. 9 - A smooth flat plate 2.4 m long and 0.6 m wide is...Ch. 9 - Consider flow of air over a flat plate. On one...Ch. 9 - A thin flat plate, L = 9 in. long and b = 3 ft...Ch. 9 - For a laminar boundary layer on a flat plate,...Ch. 9 - Air at atmospheric pressure and 20C flows over...Ch. 9 - A thin flat plate is installed in a water tunnel...Ch. 9 - Assume laminar boundary-layer flow to estimate the...Ch. 9 - Assume laminar boundary-layer flow to estimate the...Ch. 9 - Assume laminar boundary-layer flow to estimate the...Ch. 9 - Prob. 34PCh. 9 - Water at 10C flows over a flat plate at a speed of...Ch. 9 - Use the momentum integral equation to derive...Ch. 9 - A smooth flat plate 1.6 ft long is immersed in 68F...Ch. 9 - Prob. 38PCh. 9 - A developing boundary layer of standard air on a...Ch. 9 - Assume the flow conditions given in Example 9.3....Ch. 9 - A flat-bottomed barge having a 150 ft 20 ft...Ch. 9 - European InterCity Express trains operate at...Ch. 9 - Grumman Corp. has proposed to build a magnetic...Ch. 9 - Repeat Problem 9.32, for an air flow at 80 ft/s,...Ch. 9 - The velocity profile in a turbulent boundary-layer...Ch. 9 - The U.S. Navy has built the Sea Shadow, which is a...Ch. 9 - The two rectangular smooth flat plates are to have...Ch. 9 - Standard air flows over a horizontal smooth flat...Ch. 9 - Air at standard conditions flows over a flat...Ch. 9 - A uniform flow of standard air at 60 m/s enters a...Ch. 9 - A laboratory wind tunnel has a flexible upper wall...Ch. 9 - Air flows in a cylindrical duct of diameter D = 6...Ch. 9 - Perform a cost-effectiveness analysis on a typical...Ch. 9 - Table 9.1 (on the web) shows the numerical results...Ch. 9 - A fluid flow enters the plane-wall diffuser that...Ch. 9 - For flow over a flat plate with zero pressure...Ch. 9 - A flat-bottomed barge, 80 ft long and 35 ft wide,...Ch. 9 - A towboat for river barges is tested in a towing...Ch. 9 - Plot the local friction coefficient cf, the...Ch. 9 - A smooth plate 3 m long and 0.9 m wide moves...Ch. 9 - Resistance of a barge is to be determined from...Ch. 9 - A nuclear submarine cruises fully submerged at 27...Ch. 9 - You are asked by your college crew to estimate the...Ch. 9 - The drag coefficient of a circular disk when...Ch. 9 - A steel sphere of 0.25 in. diameter has a velocity...Ch. 9 - A steel sphere (SG = 7.8) of 13 mm diameter falls...Ch. 9 - A sheet of plastic material 0.5 in. thick, with...Ch. 9 - As part of the 1976 bicentennial celebration, an...Ch. 9 - What constant speed will be attained by a lead (SG...Ch. 9 - Assuming a critical Reynolds number of 0.1,...Ch. 9 - Glass spheres of 0.1 in. diameter fall at constant...Ch. 9 - A rotary mixer is constructed from two circular...Ch. 9 - Calculate the drag of a smooth sphere of 0.3 m...Ch. 9 - Calculate the drag of a smooth sphere of 0.5 m...Ch. 9 - A cylindrical chimney 0.9 m in diameter and 22.5 m...Ch. 9 - The resistance to motion of a good bicycle on...Ch. 9 - Ballistic data obtained on a firing range show...Ch. 9 - A standard marine torpedo is 0.533 m in diameter...Ch. 9 - A large truck has an essentially boxlike body that...Ch. 9 - At a surprise party for a friend youve tied a...Ch. 9 - A 0.5-m-diameter hollow plastic sphere containing...Ch. 9 - A simple but effective anemometer to measure wind...Ch. 9 - The Willis Tower (formerly the Sears Tower) in...Ch. 9 - It is proposed to build a pyramidal building with...Ch. 9 - Calculate the drag forces on a 1/200 scale model...Ch. 9 - A circular disk is hung in an air stream from a...Ch. 9 - A vehicle is built to try for the land-speed...Ch. 9 - An F-4 aircraft is slowed after landing by dual...Ch. 9 - A tractor-trailer rig has frontal area A = 102 ft2...Ch. 9 - A 180hp sports car of frontal area 1.72 m2, with a...Ch. 9 - An object falls in air down a long vertical chute....Ch. 9 - Prob. 99PCh. 9 - A light plane tows an advertising banner over a...Ch. 9 - The antenna on a car is 10 mm in diameter and 1.8...Ch. 9 - Consider small oil droplets (SG = 0.85) rising in...Ch. 9 - Standard air is drawn into a low-speed wind...Ch. 9 - A small sphere with D = 6 mm is observed to fall...Ch. 9 - A tennis ball with a mass of 57 g and diameter of...Ch. 9 - A water tower consists of a 12-m-diameter sphere...Ch. 9 - A cast-iron 12-pounder cannonball rolls off the...Ch. 9 - A rectangular airfoil of 40 ft span and 6 ft chord...Ch. 9 - A rectangular airfoil of 9 m span and 1.8 m chord...Ch. 9 - Why is it possible to kick a football farther in a...Ch. 9 - If CL = 1.0 and CD = 0.05 for an airfoil, then...Ch. 9 - A wing model of 5 in. chord and 2.5 ft span is...Ch. 9 - A barge weighing 8820 kN that is 10 m wide, 30 m...Ch. 9 - A spherical sonar transducer with 15 in. diameter...Ch. 9 - While walking across campus one windy day, an...Ch. 9 - If the mean velocity adjacent to the top of a wing...Ch. 9 - The NACA 23015 airfoil is to move at 180 mph...Ch. 9 - A human-powered aircraft has a gross weight of 240...Ch. 9 - WiffleTM balls made from light plastic with...Ch. 9 - A model airfoil of chord 6 in. and span 30 in. is...Ch. 9 - An antique airplane carries 50 m of external guy...Ch. 9 - How do cab-mounted wind deflectors for...Ch. 9 - An airplane with an effective lift area of 25 m2...Ch. 9 - The U.S. Air Force F-16 fighter aircraft has wing...Ch. 9 - A light airplane, with mass M = 1000 kg, has a...Ch. 9 - A light airplane has 35-ft effective wingspan and...Ch. 9 - Assume the Boeing 727 aircraft has wings with NACA...Ch. 9 - Jim Halls Chaparral 2F sports-racing cars in the...Ch. 9 - Some cars come with a spoiler, a wing section...Ch. 9 - Roadside signs tend to oscillate in a twisting...Ch. 9 - Air moving over an automobile is accelerated to...Ch. 9 - A class demonstration showed that lift is present...Ch. 9 - Rotating cylinders were proposed as a means of...Ch. 9 - A baseball pitcher throws a ball at 80 mph. Home...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
Why are inertia welds of more consistent quality than friction welds?
DeGarmo's Materials and Processes in Manufacturing
The quantity ms into s.
Engineering Mechanics: Statics & Dynamics (14th Edition)
Determine the slope of the simply supported beam at A. E = 200 GPa and I = 39.9(106) m4. F126
Mechanics of Materials (10th Edition)
3. The longest sea bridge, the Jiaozhou Bay Bridge in China, spans 26.4 miles [mi]. The longest sea bridge in t...
Thinking Like an Engineer: An Active Learning Approach (4th Edition)
If it is placed on the ground for which the coefficient of kinetic friction is c = 0.5, determine the time requ...
Engineering Mechanics: Dynamics (14th Edition)
Pressurized water at Tm,i=200C is pumped at m=2kg/s from a power plant to a nearby industrial user through a th...
Fundamentals of Heat and Mass Transfer
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- The answer is handwritten and step by steparrow_forwardAtmospheric air at 20°C flows at 10 m/s on both sides over a 2-m long by 4-m wide flat plate. Calculate the maximum boundary layer thickness and the drag force if the plate is smooth and if rough.arrow_forwardAnswer correctly. Here is the Translation. "A luxury sports car has an area of 2 m² and there is a drag coefficient of 0.29 at a speed of 90 km/h. Calculate the drag force exerted on the car at this speed"arrow_forward
- A cloud of coal particles is traveling through a system. The cloud diameter estimated to be 0.027 m and the individual particles are 50 um in diameter with the density of 1300 kg/m'. The total cloud is moving such that its drag coefficient is constant at 0.44. The individual particles in the cloud move much slower, such that the drag coefficient given by stock's law. The system has atmospheric air transporting and the cloud density is 190 kg/m3. Determine the ratio of internal velocity to cloud velocity. Atmospheric air density 1.2 kg/m'.arrow_forwardThe sphere of diameter of 5.0 cm is moving in still water at a velocity of 2.0 m/s. The drag coefficient is 0.44. Determine the hydrodynamic drag acting on the sphere if the density of water is 997 kg/m^3*arrow_forwardf6arrow_forward
- Nonearrow_forwardForce acting on a truck (frontal area of 2.01 m?) in the flow direction as shown is measured experimentally in a wind tunnel as (x + 100) N. For the truck at design conditions of 1 atm, 20°C and 95 km/h, (a) Determine the force coefficient of this car (b) What can this force coefficient be classified as, drag coefficient or lift coefficient? Why? Use x =190.6 U=95 hm/harrow_forwardFrom Table the drag coefficient of a wide plate normalto a stream is approximately 2.0. Let the stream conditionsbe U∞ and p∞. If the average pressure on the front of theplate is approximately equal to the free-stream stagnationpressure, what is the average pressure on the rear?arrow_forward
- I need the answer as soon as possiblearrow_forwardA car is moving at a speed of 70 km/h in air at 20°C. The frontal area of the car is 2.4 m2. If the drag force acting on the car in the flow direction is 205 N, the drag coefficient of the car is (a) 0.312 (b) 0.337 (c) 0.354 (d ) 0.375 (e) 0.391arrow_forwardAir flows parallel to the surface of a smooth flat plate 10 m long. The boundary thickness at the leading edge. The Reynolds number at the trailing edge of the plate is 107. Calculate the total drag force due to skin friction on one side of the plate per unit width. Assume that for laminar boundary layer, up to Re, = 5 x 105, the skin friction coefficient is Gr 1.328(Re)-1/2 and for turbulent boundary layer 0.078(Re)-1/5. Take the density of air as 1.2 kg/m³ and Its dynamic viscosity as 1.8 x 10-5 kg/msarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
Heat Transfer – Conduction, Convection and Radiation; Author: NG Science;https://www.youtube.com/watch?v=Me60Ti0E_rY;License: Standard youtube license