College Physics: A Strategic Approach (3rd Edition)
3rd Edition
ISBN: 9780321879721
Author: Randall D. Knight (Professor Emeritus), Brian Jones, Stuart Field
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 8, Problem 37P
A mineshaft has an ore elevator hung from a single braided cable of diameter 2.5 cm. Young’s modulus of the cable is 10 × 1010 N/m2. When the cable is fully extended, the end of the cable is 800 m below the support. How much does the fully extended cable stretch when 1000 kg of ore is loaded into the elevator?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A mineshaft has an ore elevator hung from a single braided cable of diameter 2.5 cm. Young’s modulus of the cable is 10 x 1010 N/m2. When the cable is fully extended, the end of the cable is 800 m below the support. How much does the fully extended cable stretch when 1000 kg of ore is loaded?
A cable is 100 m long and has a cross-sectional area of 1.0 x 10-6 m2. A 1000 N force is applied to stretch the cable. The elastic modulus for the cable is 1.0 × 1011 N/m2. How far does it stretch?
A high-carbon steel wire, circular in cross-section, has a diameter of 14 mm. What is the force (in newtons) needed to break it? The ultimate tensile stress of high-carbon steel is 1.0 x 109 Pa.
Chapter 8 Solutions
College Physics: A Strategic Approach (3rd Edition)
Ch. 8 - An object is acted upon by two (and only two)...Ch. 8 - Prob. 2CQCh. 8 - Could a ladder on a level floor lean against a...Ch. 8 - If you are using a rope to raise a tall mast,...Ch. 8 - Prob. 5CQCh. 8 - Prob. 6CQCh. 8 - Prob. 7CQCh. 8 - A spring exerts a 10 N force after being stretched...Ch. 8 - The left end of a spring is attached to a wall....Ch. 8 - A spring is attached to the floor and pulled...
Ch. 8 - A typical mattress has a network of springs that...Ch. 8 - Take a spring and cut it in half to make two...Ch. 8 - A wire is stretched right to its breaking point by...Ch. 8 - Steel nails are rigid and unbending. Steel wool is...Ch. 8 - The rod in Figure Q8.15 pivots around an axle at...Ch. 8 - Two children hold opposite ends of a lightweight,...Ch. 8 - Prob. 17MCQCh. 8 - Prob. 18MCQCh. 8 - Prob. 19MCQCh. 8 - Prob. 20MCQCh. 8 - Prob. 21MCQCh. 8 - Prob. 22MCQCh. 8 - You have a heavy piece of equipment hanging from a...Ch. 8 - Prob. 24MCQCh. 8 - Prob. 1PCh. 8 - Prob. 2PCh. 8 - Prob. 3PCh. 8 - Prob. 4PCh. 8 - Youre carrying a 3.6-m-long, 25 kg pole to a...Ch. 8 - Prob. 6PCh. 8 - How much torque must the pin exert to keep the rod...Ch. 8 - Prob. 8PCh. 8 - Prob. 9PCh. 8 - Consider the procedure for measuring a womans...Ch. 8 - Prob. 11PCh. 8 - Prob. 12PCh. 8 - Prob. 13PCh. 8 - Prob. 14PCh. 8 - Prob. 15PCh. 8 - Prob. 16PCh. 8 - Prob. 17PCh. 8 - The stability of a vehicle is often rated by the...Ch. 8 - You want to slowly push a stiff board across a 20...Ch. 8 - Prob. 20PCh. 8 - A car manufacturer claims that you can drive its...Ch. 8 - Prob. 22PCh. 8 - One end of a spring is attached to a wall. A 25 N...Ch. 8 - An orthodontic spring, connected between the upper...Ch. 8 - Experiments using optical tweezers measure the...Ch. 8 - A spring has an unstretched length of 10 cm. It...Ch. 8 - One end of a 10-cm-long spring is attached to the...Ch. 8 - A spring stretches 5.0 cm when a 0.20 kg block is...Ch. 8 - A 1.2 kg block is hung from a vertical spring,...Ch. 8 - You need to make a spring scale to measure the...Ch. 8 - A force stretches a wire by 1.0 mm. a. A second...Ch. 8 - What hanging mass will stretch a 2.0-m-long,...Ch. 8 - How much force does it take to stretch a...Ch. 8 - An 80-cm-long, 1.0-mm-diameter steel guitar string...Ch. 8 - A student is testing a 1.0 m length of...Ch. 8 - A 1.2-m-long steel rod with a diameter of 0.50 cm...Ch. 8 - A mineshaft has an ore elevator hung from a single...Ch. 8 - The normal force of the ground on the foot can...Ch. 8 - A three-legged wooden bar stool made out of solid...Ch. 8 - Prob. 40PCh. 8 - A glass optical fiber in a communications system...Ch. 8 - The Achilles tendon connects the muscles in your...Ch. 8 - Prob. 43GPCh. 8 - Prob. 44GPCh. 8 - Using the information in Figure 8.2, calculate the...Ch. 8 - A woman weighing 580 N does a pushup from her...Ch. 8 - Prob. 47GPCh. 8 - Prob. 48GPCh. 8 - Prob. 49GPCh. 8 - The wheel of mass m in Figure P8.50 is pulled on...Ch. 8 - A 5.0 kg mass hanging from a spring scale is...Ch. 8 - Two identical, side-by-side springs with spring...Ch. 8 - Two springs have the same equilibrium length but...Ch. 8 - Figure P8.54 shows two springs attached to a block...Ch. 8 - A 60 kg student is standing atop a spring in an...Ch. 8 - A 25 kg child bounces on a pogo stick. The pogo...Ch. 8 - Figure P8.57 shows a lightweight plank supported...Ch. 8 - In the hammer throw, an athlete spins a heavy mass...Ch. 8 - There is a disk of cartilage between each pair of...Ch. 8 - In Example 8.1, the tension in the biceps tendon...Ch. 8 - Larger animals have sturdier bones than smaller...Ch. 8 - Orb spiders make silk with a typical diameter of...Ch. 8 - Prob. 63MSPPCh. 8 - Prob. 64MSPPCh. 8 - Prob. 65MSPP
Additional Science Textbook Solutions
Find more solutions based on key concepts
A suspension bridge oscillates with an effective force constant of 1.00108 N/m . (a) How much energy is needed ...
University Physics Volume 1
Particles of light have no mass. Does the Sun’s mass change as a result of all the light it emits? Explain.
Modern Physics
34.106 An Object at an Angle. A 16.0-cm-long pencil is placed at a 45.0° angle, with its center 15.0 cm above t...
University Physics with Modern Physics (14th Edition)
Write each number in scientific notation.
4. 14,500
Applied Physics (11th Edition)
The pV-diagram of the Carnot cycle.
Sears And Zemansky's University Physics With Modern Physics
1. A 150-kg football player collides head-on with a 75-kg running back. During the collision, the heavier playe...
Physics: Principles with Applications
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.Similar questions
- A uniform wire (Y = 2.0 1011 N/m2) is subjected to a longitudinal tensile stress of 4.0 107 N/m2. What is the fractional change in the length of the wire?arrow_forwardAn aluminium (=2.7g/cm3) wire is suspended from the ceiling and hangs vertically. How long must the wire be before the stress at its upper end reaches the proportionality limit, which is 8.0107N/m2 ?arrow_forwardIn Example 14.3, we found that one of the steel cables supporting an airplane at the Udvar-Hazy Center was under a tension of 9.30 103 N. Assume the cable has a diameter of 2.30 era and an initial length of 8.00 m before the plane is suspended on the cable. How much longer is the cable when the plane is suspended on it?arrow_forward
- Assume Youngs modulus for bone is 1.50 1010 N/m2. The bone breaks if stress greater than 1.50 108 N/m2 is imposed on it. (a) What is the maximum force that can be exerted on the femur bone in the leg if it has a minimum effective diameter of 2.50 cm? (b) If this much force is applied compressively, by how much does the 25.0-cm-long bone shorten?arrow_forwardA 5.45-N beam of uniform density is 1.60 m long. The beam is supported at an angle of 35.0 by a cable attached to one end. There is a pin through the other end of the beam (Fig. P14.30). Use the values given in the figure to find the tension in the cable. FIGURE P14.30arrow_forwardWhat Is Static Equilibrium? Problems 13 are grouped. 1. C A ball is attached to a strong, lightweight rod (Fig. P14.1). The rod is supported by a horizontal pin near the top. The ball is at rest. Is the ball in static equilibrium? If not, why not? If so, which type of equilibrium is itstable, unstable, or neutral? Hint: What would happen if you displaced the ball slightly? FIGURE P14.1arrow_forward
- A brass wire and a steel wire, both of the same length, are extended by 1.0 mm under the same force. Is the cross-sectional radius of the brass wire more, less, or equal to the cross-sectional radius of the steel wire? Explain. Youngs moduli for brass and steel are 1.0 1010 N/m2 and 2.0 1011 N/m2, respectively.arrow_forwardA steel cable 2.00 m in length and with cross-sectional radius 0.350 mm is used to suspend from the ceiling a 10.0-kg model aircraft that is flying in a horizontal circle with an angular speed of 6.00 rad/s. What is the strain produced in the cable?arrow_forwardA horizontal, rigid bar of negligible weight is fixed against a vertical wall at one end and supported by a vertical string at the other end. The bar has a length of 50.0 cm and is used to support a hanging block of weight 400.0 N from a point 30.0 cm from the wall as shown in Figure P14.81. The string is made from a material with a tensile strength of 1.2 108 N/m2. Determine the largest diameter of the string for which it would still break. FIGURE P14.81arrow_forward
- Consider the sketch of a portion of a roller-coaster track seen in Figure P14.5. Identify places on the track that could be considered possible locations of static equilibrium for a rollercoaster car were the car to be placed at any spot on the track.Which places are candidate locations for stable, unstable, andneutral static equilibrium? FIGURE P14.5arrow_forwardAt a museum, a 1300-kg model aircraft is hung from a lightweight beam of length 12.0 m that is free to pivot about its base and is supported by a massless cable (Fig. P14.38). Ignore the mass of the beam. a. What is the tension in the section of the cable between the beam and the wall? b. What are the horizontal and vertical forces that the pivot exerts on the beam? FIGURE P14.38 (a) From the free-body diagram, the angle that the string tension makes with the beam is = 55.0 + 18.0 = 73.0, and the perpendicular component of the string tension is FT sin73.0. Summing torques around the base of the rod gives (Eq. 14.2): =0:(12.0m)(1300kg)(9.81m/s2)cos55.0+FT(12.0m)sin73.0=0FT=(12.0m)(1300kg)(9.81m/s2)cos55.0(12.0m)sin73.0FT=7.65103N Figure P14.38ANS (b) Using force balance (Eq. 14.1): Fx=0:FHFTcos18.0=0FH=FTcos18.0=[(12.0m)(1300kg)(9.81m/s2)cos55.0(12.0m)sin73.0]cos18.0=7.27103NFy=0:FVFTsin18.0(1300kg)(9.81m/s2)=0 FV=FTsin18.0+(1300kg)gFV=[(12.0m)(1300kg)(9.81m/s2)cos55.0(12.0m)sin73.0]sin18.0+(1300kg)(9.81m/s2)FV=1.51104Narrow_forwardThe lintel of prestressed reinforced concrete in Figure P12.27 is 1.50 m long. The concrete encloses one steel reinforcing rod with cross-sectional area 1.50 cm2. The rod joins two strong end plates. The cross-sectional area of the concrete perpendicular to the rod is 50.0 cm2. Youngs modulus for the concrete is 30.0 109 N/m2. After the concrete cures and the original tension T1 in the rod is released, the concrete is to be under compressive stress 8.00 106 N/m2. (a) By what distance will the rod compress the concrete when the original tension in the rod is released? (b) What is the new tension T2 in the rod? (c) The rod will then be how much longer than its unstressed length? (d) When the concrete was poured, the rod should have been stretched by what extension distance from its unstressed length? (e) Find the required original tension T1 in the rod. Figure P12.27arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Physics for Scientists and Engineers: Foundations...PhysicsISBN:9781133939146Author:Katz, Debora M.Publisher:Cengage Learning
University Physics Volume 1PhysicsISBN:9781938168277Author:William Moebs, Samuel J. Ling, Jeff SannyPublisher:OpenStax - Rice University
Physics for Scientists and EngineersPhysicsISBN:9781337553278Author:Raymond A. Serway, John W. JewettPublisher:Cengage Learning
Physics for Scientists and Engineers with Modern ...PhysicsISBN:9781337553292Author:Raymond A. Serway, John W. JewettPublisher:Cengage Learning
Physics for Scientists and Engineers, Technology ...PhysicsISBN:9781305116399Author:Raymond A. Serway, John W. JewettPublisher:Cengage Learning
College PhysicsPhysicsISBN:9781285737027Author:Raymond A. Serway, Chris VuillePublisher:Cengage Learning
Physics for Scientists and Engineers: Foundations...
Physics
ISBN:9781133939146
Author:Katz, Debora M.
Publisher:Cengage Learning
University Physics Volume 1
Physics
ISBN:9781938168277
Author:William Moebs, Samuel J. Ling, Jeff Sanny
Publisher:OpenStax - Rice University
Physics for Scientists and Engineers
Physics
ISBN:9781337553278
Author:Raymond A. Serway, John W. Jewett
Publisher:Cengage Learning
Physics for Scientists and Engineers with Modern ...
Physics
ISBN:9781337553292
Author:Raymond A. Serway, John W. Jewett
Publisher:Cengage Learning
Physics for Scientists and Engineers, Technology ...
Physics
ISBN:9781305116399
Author:Raymond A. Serway, John W. Jewett
Publisher:Cengage Learning
College Physics
Physics
ISBN:9781285737027
Author:Raymond A. Serway, Chris Vuille
Publisher:Cengage Learning
An Introduction to Stress and Strain; Author: The Efficient Engineer;https://www.youtube.com/watch?v=aQf6Q8t1FQE;License: Standard YouTube License, CC-BY