Degarmo's Materials And Processes In Manufacturing
13th Edition
ISBN: 9781119492825
Author: Black, J. Temple, Kohser, Ronald A., Author.
Publisher: Wiley,
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 30, Problem 7RQ
A drawing calls for making a groove 23 mm wide and 3 mm deep by chemical machining. What should be the width of the opening in the maskant?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
The tailstock has two major parts a bottom casting and a top casting is machined very accurately to fit the ways of the lathe [(a dogs (b) bed (c) carriage (d) mandrel
What would a .010 - .020 cutback of a 14.500 Diameter be?
Sketch and explain any four Shaper operations?
Chapter 30 Solutions
Degarmo's Materials And Processes In Manufacturing
Ch. 30 - How do the MRRs for most NTM processes compare to...Ch. 30 - What are the steps in chemical machining using...Ch. 30 - In chemical machining, should the etchant be...Ch. 30 - What are the advantages of chemical blanking over...Ch. 30 - How are multiple depths of cut (steps) produced by...Ch. 30 - Would it be feasible to produce a groove 2 mm wide...Ch. 30 - A drawing calls for making a groove 23 mm wide and...Ch. 30 - Could an ordinary steel weldment be chemically...Ch. 30 - How could you produce a tapered section by...Ch. 30 - What is the principal application of...
Ch. 30 - How is ECM related to chemical machining?Ch. 30 - What effect does work material hardness have on...Ch. 30 - What is the principal cause of tool wear in ECM?Ch. 30 - Would electrochemical grinding be a suitable...Ch. 30 - Upon what factors does the metal removal rate...Ch. 30 - Why is the tool insulated in the ECM schematic?Ch. 30 - What is the nature of the surface obtained by...Ch. 30 - What is the principal advantage of using a moving...Ch. 30 - What effect would increasing the voltage have on...Ch. 30 - If a metal part is quite brittle and the part will...Ch. 30 - If you had to make several holes in a large number...Ch. 30 - Prob. 22RQCh. 30 - Explain (using a little physics and metallurgy)...Ch. 30 - Prob. 24RQCh. 30 - What are some possible defects that can result...Ch. 30 - What are some other uses for the laser other than...Ch. 30 - How does the laser produce coherent light...Ch. 30 - What is ablation?Ch. 30 - What is an excimer?Ch. 30 - In Figure 30.16, what is the protective tape...Ch. 30 - Why is the EBM process done in a vacuum?Ch. 30 - What is the major problem with the redesigned cap...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Broaching is an example of. joining process primary shaping process surface finishing process secondary machining processarrow_forwardwing (3) You are to produce a machine part (a shaft) with different diameters S0mm.35mm and 30mm with thread and keyway at the end of the shaft (a) How many machines and cutting tools will you use to produce this part 1arrow_forwardQuestion 3. a. A cast iron component for motorcycle is to be turned with machine settings of feed = 0.22 mm/rev, and speed = 100 m/min. The cutting tool is a carbide tip with a nose radius of 1.2 mm and the rai for the material at a cutting speed of 100 m/min is 1.3. Calculate the surface roughness for this cut. [6 marks]arrow_forward
- How many parts per hour will a jig produce if the machining time is 30 seconds and it takes 2 seconds to load the part and 2 seconds to unload the part?arrow_forward9) Which type of edge preparations are easier to make/prepare? Bevel grooves OJ grooves OU grooves O None of thesearrow_forwardTandem drawing of wires and tubes is necessary because; Surface finish improves after every drawing stage OIt is not possible to reduce at one stage O Annealing is needed between stages Accuracy in dimensions is not possible otherwise Which of the following abrasive materials is most appropriate for grinding nonferrous metals? Silicon carbide O Aluminum oxide Cubic boron nitride Diamondarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Precision Machining Technology (MindTap Course Li...Mechanical EngineeringISBN:9781285444543Author:Peter J. Hoffman, Eric S. Hopewell, Brian JanesPublisher:Cengage LearningWelding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Precision Machining Technology (MindTap Course Li...
Mechanical Engineering
ISBN:9781285444543
Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes
Publisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Types of Manufacturing Process | Manufacturing Processes; Author: Magic Marks;https://www.youtube.com/watch?v=koULXptaBTs;License: Standard Youtube License